[PATCH v5 2/3] arm64: dts: imx: Add i.mx8mm nitrogen8mm basic dts support
Adrien Grassein
adrien.grassein at gmail.com
Thu Jan 28 12:23:34 EST 2021
Hi Marco,
Thanks for your time.
Le jeu. 28 janv. 2021 à 17:18, Marco Felsch <m.felsch at pengutronix.de> a écrit :
>
> Hi Adrien,
>
> thanks for the patch. I've made only a few comments inline.
>
> On 21-01-18 12:15, Adrien Grassein wrote:
> > Tested with a basic Build Root configuration booting from sdcard.
> >
> > Signed-off-by: Adrien Grassein <adrien.grassein at gmail.com>
> > Reviewed-by: Krzysztof Kozlowski <krzk at kernel.org>
> > ---
> > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > .../dts/freescale/imx8mm-nitrogen8mm_rev2.dts | 395 ++++++++++++++++++
> > 2 files changed, 396 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index 38559943c15d..398b5cb4f3e2 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -49,6 +49,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
> > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen8mm_rev2.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-thor96.dtb
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> > new file mode 100644
> > index 000000000000..755088387ea5
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> > @@ -0,0 +1,395 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Device Tree file for Boundary Devices i.MX8MMini Nitrogen8MM Rev2 board.
> > + * Adrien Grassein <adrien.grassein at gmail.com.com>
> > + */
> > +/dts-v1/;
> > +#include "imx8mm.dtsi"
> > +
> > +/ {
> > + model = "Boundary Devices i.MX8MMini Nitrogen8MM Rev2";
> > + compatible = "boundary,imx8mm-nitrogen8mm", "fsl,imx8mm";
> > +};
> > +
> > +&A53_0 {
> > + cpu-supply = <®_sw3>;
> > +};
> > +
> > +&A53_1 {
> > + cpu-supply = <®_sw3>;
> > +};
> > +
> > +&A53_2 {
> > + cpu-supply = <®_sw3>;
> > +};
> > +
> > +&A53_3 {
> > + cpu-supply = <®_sw3>;
> > +};
> > +
> > +&fec1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fec1>;
> > + phy-mode = "rgmii-id";
> > + phy-handle = <ðphy0>;
> > + fsl,magic-packet;
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ethphy0: ethernet-phy at 4 {
> > + compatible = "ethernet-phy-id004d.d072",
> ^
> Do we really need to add the id here?
Yes, I don't know why, but the chip it's not recognized via the mdio interface.
I will do further tests but I think it's needed.
> > + "ethernet-phy-ieee802.3-c22";
> > + reg = <4>;
> > + interrupts-extended = <&gpio3 16 IRQ_TYPE_LEVEL_LOW>;
> > + };
> > + };
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <400000>;
> ^
> Is the i2c errata fixed on the imx8?
I don't know. What is this errata?
Should I set a lower speed for the particular i2c?
>
> > + pinctrl-names = "default", "gpio";
> ^
> no pinctrl for gpio.
Yes, it's a bug, thanks
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + pmic at 8 {
> > + compatible = "nxp,pf8121a";
> > + reg = <0x8>;
> > +
> > + regulators {
> > + reg_ldo1: ldo1 {
> ^
> alignment
OK
> > + regulator-min-microvolt = <1500000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_ldo2: ldo2 {
> > + regulator-min-microvolt = <1500000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_ldo3: ldo3 {
> > + regulator-min-microvolt = <1500000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_ldo4: ldo4 {
> > + regulator-min-microvolt = <1500000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_buck1: buck1 {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_buck2: buck2 {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_sw3: buck3 {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_buck4: buck4 {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_buck5: buck5 {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_buck6: buck6 {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_buck7: buck7 {
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + reg_vsnvs: vsnvs {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
>
> Do we really need to have all regulators marked as always-on?
>
I used the definition present on the example.
I will remove this (for the one I don't use).
> > + };
> > + };
> > +};
> > +
> > +&i2c3 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default", "gpio";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + i2cmux at 70 {
> > + compatible = "nxp,pca9540";
> > + reg = <0x70>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + i2c3 {
> > + reg = <0>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + rtc at 68 {
> > + compatible = "microcrystal,rv4162";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3a_rv4162>;
> > + reg = <0x68>;
>
> reg should be the 2nd property, after the compatible.
>
OK.
> > + interrupts-extended = <&gpio4 22 IRQ_TYPE_LEVEL_LOW>;
> > + wakeup-source;
> > + };
> > + };
> > + };
> > +};
> > +
> > +/* console */
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > + assigned-clocks = <&clk IMX8MM_CLK_UART2>;
> > + assigned-clock-parents = <&clk IMX8MM_CLK_24M>;
> > + status = "okay";
> > +};
> > +
> > +/* eMMC */
> > +&usdhc1 {
> > + bus-width = <8>;
> > + sdhci-caps-mask = <0x80000000 0x0>;
> ^
> This is a SD host controller property according the doc.
>
Yes, I don't understand the point, sorry.
This property is read by the host driver, but should be present here
(like in some other dts).
> > + non-removable;
> > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> > + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> > + status = "okay";
> > +};
> > +
> > +/* sdcard */
> > +&usdhc2 {
> > + bus-width = <4>;
> > + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > + pinctrl-0 = <&pinctrl_usdhc2>;
> > + pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> > + pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> > + vqmmc-supply = <®_ldo2>;
> > + status = "okay";
> > +};
> > +
> > +&wdog1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wdog>;
> > + fsl,ext-reset-output;
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog>;
>
> It would be nice to avoid such hog's. Instead those gpios should get
> configured by the device(s) using those.
>
Once again (sorry), I don't understand the point.
I did this like any other imx8 board (imx8mq-nitrogem for example).
> Regards,
> Marco
>
> > +
> > + pinctrl_fec1: fec1grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
> > + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
> > + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
> > + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
> > + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
> > + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
> > + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
> > + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
> > + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
> > + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
> > + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
> > + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
> > + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
> > + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
> > + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x159
> > + >;
> > + };
> > +
> > + pinctrl_hog: hoggrp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x09
> > + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x09
> > + >;
> > + };
> > +
> > + pinctrl_i2c1: i2c1grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
> > + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
> > + >;
> > + };
> > +
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
> > + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
> > + >;
> > + };
> > +
> > + pinctrl_i2c3a_rv4162: i2c3a-rv4162grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1c0
> > + >;
> > + };
> > +
> > + pinctrl_uart2: uart2grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
> > + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
> > + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0
> > + MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x141
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
> > + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
> > + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
> > + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
> > + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
> > + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
> > + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
> > + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
> > + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
> > + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> > + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> > + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> > + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> > + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
> > + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
> > + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
> > + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
> > + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
> > + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3: usdhc3grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
> > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
> > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
> > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
> > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
> > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
> > + MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x03
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
> > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
> > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
> > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
> > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
> > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
> > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
> > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
> > + >;
> > + };
> > +
> > + pinctrl_wdog: wdoggrp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x140
> > + >;
> > + };
> > +};
> > --
> > 2.25.1
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> >
>
> --
> Pengutronix e.K. | |
> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Thanks,
More information about the linux-arm-kernel
mailing list