[PATCH v2 2/4] arm64: dts: ti: k3: squelch warnings regarding no #address-cells for interrupt-controller

[Rob Herring]

On Thu, Nov 19, 2020 at 01:17:36PM +0200, Grygorii Strashko wrote:
> 
> 
> On 18/11/2020 17:12, Nishanth Menon wrote:
> > On 13:38-20201118, Grygorii Strashko wrote:
> > > Hi Rob,
> > > 
> > > On 17/11/2020 18:19, Sekhar Nori wrote:
> > > > With dtc 1.6.0, building TI device-tree files with W=2 results in warnings
> > > > like below for all interrupt controllers.
> > > > 
> > > > /bus at 100000/bus at 30000000/interrupt-controller1: Missing #address-cells in interrupt provider
> > > > 
> > > > Fix these by adding #address-cells = <0>; for all interrupt controllers in
> > > > TI device-tree files. Any other #address-cells value is really only needed
> > > > if interrupt-map property is being used (which is not the case for existing
> > > > TI device-tree files)
> > > > 
> > > > Signed-off-by: Sekhar Nori <nsekhar at ti.com>
> > > > ---
> > > >    arch/arm64/boot/dts/ti/k3-am65-main.dtsi              |  5 +++++
> > > >    arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi            |  2 ++
> > > >    arch/arm64/boot/dts/ti/k3-am654-base-board.dts        |  1 +
> > > >    arch/arm64/boot/dts/ti/k3-j7200-main.dtsi             |  3 +++
> > > >    arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi       |  1 +
> > > >    arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts |  1 +
> > > >    arch/arm64/boot/dts/ti/k3-j721e-main.dtsi             | 11 +++++++++++
> > > >    arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi       |  3 +++
> > > >    8 files changed, 27 insertions(+)
> > > > 
> > > > diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > > > index aa8725db0187..55aaa1404d7d 100644
> > > > --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > > > +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > > > @@ -440,6 +440,7 @@
> > > >    		interrupt-controller;
> > > >    		interrupt-parent = <&gic500>;
> > > >    		#interrupt-cells = <1>;
> > > > +		#address-cells = <0>;
> > > Does it really required or mandatory to have #address-cells = <0>; defined for interrupt-controller DT nodes which
> > > do not have child nodes and no "interrupt-map"?
> > 
> > Just to help clarify (I could be mistaken as well): is'nt the
> > interrupt map for user interrupt map nodes that refer to this
> > interrupt controller node to state they dont need a parent address
> > specifier - so are we claiming none of the users will have an
> > interrupt-map (now and never in the future as well) - we we might want
> > to explain why we think that is the case, and if we are expecting dtc
> > to deduce that (if so how?)?
> > 
> 
> The main reason I commented - is hope to get some clarification from DT maintainers.
> 90% of interrupt-controller nodes do not have #address-cells and I never seen in in GPIO nodes
> (most often is present in PCI and GIC nodes).
> and nobody seems fixing it. So, if we are going to move this direction it's reasonable to get clarification to be sure.
> 
> And there is no "never" here - #address-cells always can be added if really required.

Once required, how does one figure that out? It's not obvious and 
requires booting. So we need something at build time. I'm okay with 
loosening the check as long as it warns when a interrupt parent phandle 
in an interrupt-map is missing '#address-cells'.

Now that I look back at the dtc change, I'm now confused why this 
check got applied. Both David and I wanted changes in regards to 
#address-cells. Either a separate check or part of interrupt-map checks. 
And the interrupt-map check never got applied. Andre?

Rob