[PATCH v4 00/21] arm64: sunxi: Initial Allwinner H616 SoC support
Andre Przywara
andre.przywara at arm.com
Mon Jan 25 10:17:50 EST 2021
Hi,
an update from the v3 last week, to add support for the Allwinner H616
SoC. Still based on the (updated) sunxi/for-next branch.
I am omitting the MMC and pinctrl patches now, as they have been taken
by Ulf and LinusW already into their trees.
I addressed the comments from the list, though not sure if the HOSC clock
coming from the RTC is really a good idea (didn't change it).
I was hoping that at least the clock and AXP patches (01/21-06/21) could
make it into 5.12 still? That would allow booting boards from SD card.
I am happy to strip the .dtsi and .dts patch to only contain the devices
that we actually support then, if needed.
For the changes: I split the joint DT bindings patch into subsystem
specific ones, hopefully this simplifies merging. There is a new fix
for the axp20x-pek driver, and the AXP IRQ fix has been amended as well
(according to Samuel's comments).
I eventually got USB to work, by requiring PHY 2 for [EO]HCI 1 & 3 as well.
Not sure this is the right fix, it might be just one clock or reset
line from that PHY that is needed for the others as well. Will do further
experiments.
For a more detailed changelog, see below.
Thanks!
Andre
==================
This series gathers patches to support the Allwinner H616 SoC. This is
a rather uninspired SoC (Quad-A53 with the usual peripherals), but
allows for some cheap development boards and TV boxes, and supports
up to 4GB of DRAM.
Various DT binding patches are sprinkled throughout the series, to add
the new compatible names right before they are used.
Patch 2 and 3 add clock support. For the -R clock this is shared with
the H6 code, as the clocks are identical, with the H616 just having
fewer of them. The main clocks are different enough to warrant a separate
file.
Patches 5 and 6 teach the AXP MFD driver to get along without having an
interrupt, as the missing NMI pin on the H616 leads to some boards not
having the AXP IRQ line connected.
Patch 8 and 14 add some tweaks to the syscon and EMAC driver, to deal
with the second EMAC clock used for the second Ethernet controller.
Patches 15 and 18 add USB support.
The remaining patches add DT bindings, which just add the new compatible
string along with an existing name as a fallback string.
Eventually we get the .dtsi for the SoC in patch 19, and the .dts for
the OrangePi Zero2 board[1] in the last patch.
We have U-Boot and Trusted-Firmware support in a working state, booting
via FEL or SD card and even TFTPing kernels work already [2][3].
The U-Boot patches are going to be merged this week.
Many thanks to Jernej for his tremendous help on this, also for the
awesome input and help from the #linux-sunxi Freenode channel.
The whole series (including the other patches) can also be found here:
https://github.com/apritzel/linux/commits/h616-v4
Happy reviewing!
Cheers,
Andre
[1] https://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
[2] https://github.com/jernejsk/u-boot/commits/h616-v2
[3] https://github.com/apritzel/arm-trusted-firmware/commits/h616-v1
Changelog v3 .. v4:
- Drop MMC and pinctrl matches (already in some -next trees)
- Add Maxime's Acks
- Add patch to update the AXP MFD DT bindings
- Add new patch (05/21) to fix axp20x-pek driver
- Change AXP IRQ fix to check for invalid IRQ line number
- Split joint DT bindings patch (v3 18/21) into subsystems
- move dwmac variable to keep christmas tree
- Use enums for USB PHY compatible strings in DT binding
- Enable watchdog (briefly verified to work)
- Add PHY2 to HCI1&3, this fixes USB
- limit r-ccu register frame length to not collide with NMI controller
- add interrupt-controller property to AXP DT node
Changelog v2 .. v3:
- Add Rob's Acks
- Drop redundant maxItems from pinctrl DT binding
- Rename h_i2s* to just i2s* in pinctrl names
- Use more declarative i2s0_d{in,out}{0,1} names
- Add RSB pins to pinctrl
- Include RSB clocks (sharing with newly added H6 versions)
- Fix CEC clock (add 2nd enable bit, also fix predivider flag)
- Rename PMU_UNK1 register in USB PHY
- Add USB and MUSB DT binding patches
- Add MMC/SD speed modes to .dtsi
Changelog v1 .. v2:
- pinctrl: adjust irq bank map to cover undocumented GPIO bank IRQs
- use differing h_i2s0 pin output names
- r-ccu: fix number of used clocks
- ccu: remove PLL-PERIPHy(4X)
- ccu: fix gpu1 divider range
- ccu: fix usb-phy3 parent
- ccu: add missing TV clocks
- ccu: rework to CLK_OF_DECLARE style
- ccu: enable output bit for PLL clocks
- ccu: renumber clocks
- .dtsi: drop sun50i-a64-system-control fallback
- .dtsi: drop unknown SRAM regions
- .dtsi: add more (undocumented) GPIO interrupts
- .dtsi: fix I2C3 pin names
- .dtsi: use a100-emmc fallback for MMC2
- .dtsi: add second EMAC controller
- .dtsi: use H3 MUSB controller fallback
- .dtsi: fix frame size for USB PHY PMU registers
- .dtsi: add USB0 PHY references
- .dtsi: fix IR controller clock source
- .dts: fix LED naming and swap pins
- .dts: use 5V supply parent for USB supply
- .dts: drop dummy IRQ for AXP
- .dts: enable 3V3 header pin power rail
- .dts: add SPI flash node
- .dts: make USB-C port peripheral only
- add IRQ-less AXP support
- add two patches to support more than one EMAC clock
- add patch to rework and extend USB PHY support
- add DT binding documentation patches
Andre Przywara (21):
dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616
clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
clk: sunxi-ng: Add support for the Allwinner H616 CCU
dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)
Input: axp20x-pek: Bail out if AXP has no interrupt line connected
mfd: axp20x: Allow AXP chips without interrupt lines
dt-bindings: sram: sunxi-sram: Add H616 compatible string
soc: sunxi: sram: Add support for more than one EMAC clock
dt-bindings: watchdog: sun4i: Add H616 compatible string
dt-bindings: i2c: mv64xxx: Add H616 compatible string
dt-bindings: media: IR: Add H616 IR compatible string
dt-bindings: rtc: sun6i: Add H616 compatible string
dt-bindings: spi: sunxi: Add H616 compatible string
net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
phy: sun4i-usb: Rework HCI PHY (aka. "pmu_unk1") handling
dt-bindings: usb: Add H616 compatible string
dt-bindings: usb: sunxi-musb: Add H616 compatible string
phy: sun4i-usb: Add support for the H616 USB PHY
arm64: dts: allwinner: Add Allwinner H616 .dtsi file
dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
arm64: dts: allwinner: Add OrangePi Zero 2 .dts
.../devicetree/bindings/arm/sunxi.yaml | 5 +
.../clock/allwinner,sun4i-a10-ccu.yaml | 2 +
.../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +-
.../media/allwinner,sun4i-a10-ir.yaml | 16 +-
.../devicetree/bindings/mfd/axp20x.txt | 3 +-
.../phy/allwinner,sun8i-h3-usb-phy.yaml | 4 +-
.../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +
.../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
.../allwinner,sun4i-a10-system-control.yaml | 1 +
.../usb/allwinner,sun4i-a10-musb.yaml | 3 +
.../watchdog/allwinner,sun4i-a10-wdt.yaml | 12 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-h616-orangepi-zero2.dts | 242 ++++
.../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 750 +++++++++++
drivers/clk/sunxi-ng/Kconfig | 7 +-
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 48 +
drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 1150 +++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-h616.h | 56 +
drivers/input/misc/axp20x-pek.c | 4 +
drivers/mfd/axp20x.c | 17 +-
.../net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 +-
drivers/phy/allwinner/phy-sun4i-usb.c | 40 +-
drivers/soc/sunxi/sunxi_sram.c | 31 +-
include/dt-bindings/clock/sun50i-h616-ccu.h | 115 ++
include/dt-bindings/reset/sun50i-h616-ccu.h | 70 +
26 files changed, 2548 insertions(+), 67 deletions(-)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
--
2.17.5
More information about the linux-arm-kernel
mailing list