[PATCH v2] ACPI/IORT: Do not blindly trust DMA masks from firmware

[Robin Murphy]

On 2021-01-22 01:24, Moritz Fischer wrote:
> Address issue observed on real world system with suboptimal IORT table
> where DMA masks of PCI devices would get set to 0 as result.
> 
> iort_dma_setup() would query the root complex'/named component IORT
> entry for a DMA mask, and use that over the one the device has been
> configured with earlier.
> 
> Ideally we want to use the minimum mask of what the IORT contains for
> the root complex and what the device was configured with.
> 
> Fixes: 5ac65e8c8941 ("ACPI/IORT: Support address size limit for root complexes")
> Signed-off-by: Moritz Fischer <mdf at kernel.org>
> ---
> 
> Changes from v1:
> - Changed warning to FW_BUG
> - Warn for both Named Component or Root Complex
> - Replaced min_not_zero() with min()
> 
> ---
>   drivers/acpi/arm64/iort.c | 14 ++++++++++++--
>   1 file changed, 12 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/acpi/arm64/iort.c b/drivers/acpi/arm64/iort.c
> index d4eac6d7e9fb..2494138a6905 100644
> --- a/drivers/acpi/arm64/iort.c
> +++ b/drivers/acpi/arm64/iort.c
> @@ -1107,6 +1107,11 @@ static int nc_dma_get_range(struct device *dev, u64 *size)
>   
>   	ncomp = (struct acpi_iort_named_component *)node->node_data;
>   
> +	if (!ncomp->memory_address_limit) {
> +		pr_warn(FW_BUG "Named component missing memory address limit\n");
> +		return -EINVAL;
> +	}
> +
>   	*size = ncomp->memory_address_limit >= 64 ? U64_MAX :
>   			1ULL<<ncomp->memory_address_limit;
>   
> @@ -1126,6 +1131,11 @@ static int rc_dma_get_range(struct device *dev, u64 *size)
>   
>   	rc = (struct acpi_iort_root_complex *)node->node_data;
>   
> +	if (!rc->memory_address_limit) {
> +		pr_warn(FW_BUG "Root complex missing memory address limit\n");
> +		return -EINVAL;
> +	}
> +
>   	*size = rc->memory_address_limit >= 64 ? U64_MAX :
>   			1ULL<<rc->memory_address_limit;
>   
> @@ -1173,8 +1183,8 @@ void iort_dma_setup(struct device *dev, u64 *dma_addr, u64 *dma_size)
>   		end = dmaaddr + size - 1;
>   		mask = DMA_BIT_MASK(ilog2(end) + 1);
>   		dev->bus_dma_limit = end;
> -		dev->coherent_dma_mask = mask;
> -		*dev->dma_mask = mask;
> +		dev->coherent_dma_mask = min(dev->coherent_dma_mask, mask);
> +		*dev->dma_mask = min(*dev->dma_mask, mask);

Oops, I got so distracted by the "not_zero" aspect in v1 that I ended up 
thinking purely about smaller-than-default masks, but of course this 
*does* matter the other way round. And it is what we've always done on 
the DT side, so at least it makes us consistent.

FWIW I've already started writing up a patch to kill off this bit 
entirely, but either way we still can't meaningfully interpret a 
supposed DMA limit of 0 bits in a table describing DMA-capable devices, 
so for this patch as a fix,

Reviewed-by: Robin Murphy <robin.murphy at arm.com>

Thanks,
Robin.

>   	}
>   
>   	*dma_addr = dmaaddr;
>