[PATCH v1 06/17] media: camss: Add support for VFE hardware version Titan 170
Andrey Konovalov
andrey.konovalov at linaro.org
Thu Jan 14 05:48:13 EST 2021
Hi Robert,
Thank you for the patch!
On 08.01.2021 15:04, Robert Foss wrote:
> Add register definitions for version 170 of the Titan architecture
> and implement support for the RDI output mode.
>
> The RDI mode as opposed to the PIX output mode for the VFE unit does
> not support any ISP functionality. This means essentially only
> supporting dumping the output of the whatever the CSI decoder receives
> from the sensor.
>
> For example will a sensor outputting YUV pixel format frames, only
> allow the VFE to dump those frames as they are received by the ISP
> to memory through the RDI interface.
>
> Signed-off-by: Robert Foss <robert.foss at linaro.org>
> ---
> drivers/media/platform/qcom/camss/Makefile | 1 +
> .../media/platform/qcom/camss/camss-vfe-170.c | 808 ++++++++++++++++++
> drivers/media/platform/qcom/camss/camss-vfe.c | 59 +-
> drivers/media/platform/qcom/camss/camss-vfe.h | 25 +-
> .../media/platform/qcom/camss/camss-video.c | 100 +++
> drivers/media/platform/qcom/camss/camss.c | 61 ++
> 6 files changed, 1034 insertions(+), 20 deletions(-)
> create mode 100644 drivers/media/platform/qcom/camss/camss-vfe-170.c
>
> diff --git a/drivers/media/platform/qcom/camss/Makefile b/drivers/media/platform/qcom/camss/Makefile
> index 940c0ae3e003..052c4f405fa3 100644
> --- a/drivers/media/platform/qcom/camss/Makefile
> +++ b/drivers/media/platform/qcom/camss/Makefile
> @@ -11,6 +11,7 @@ qcom-camss-objs += \
> camss-vfe-4-1.o \
> camss-vfe-4-7.o \
> camss-vfe-4-8.o \
> + camss-vfe-170.o \
> camss-vfe-gen1.o \
> camss-vfe.o \
> camss-video.o \
> diff --git a/drivers/media/platform/qcom/camss/camss-vfe-170.c b/drivers/media/platform/qcom/camss/camss-vfe-170.c
> new file mode 100644
> index 000000000000..89b6c47cca22
> --- /dev/null
> +++ b/drivers/media/platform/qcom/camss/camss-vfe-170.c
> @@ -0,0 +1,808 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * camss-vfe-4-7.c
> + *
> + * Qualcomm MSM Camera Subsystem - VFE (Video Front End) Module v4.7
- the above two lines aren't updated to vfe-170
> + * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
> + * Copyright (C) 2015-2018 Linaro Ltd.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +
> +#include "camss.h"
> +#include "camss-vfe.h"
> +
> +#define VFE_HW_VERSION (0x000)
> +
> +#define VFE_GLOBAL_RESET_CMD (0x018)
> +#define GLOBAL_RESET_CMD_CORE BIT(0)
> +#define GLOBAL_RESET_CMD_CAMIF BIT(1)
> +#define GLOBAL_RESET_CMD_BUS BIT(2)
> +#define GLOBAL_RESET_CMD_BUS_BDG BIT(3)
> +#define GLOBAL_RESET_CMD_REGISTER BIT(4)
> +#define GLOBAL_RESET_CMD_PM BIT(5)
> +#define GLOBAL_RESET_CMD_BUS_MISR BIT(6)
> +#define GLOBAL_RESET_CMD_TESTGEN BIT(7)
> +#define GLOBAL_RESET_CMD_DSP BIT(8)
> +#define GLOBAL_RESET_CMD_IDLE_CGC BIT(9)
> +
> +#define VFE_CORE_CFG (0x050)
> +#define CFG_PIXEL_PATTERN_YCBYCR (0x4)
> +#define CFG_PIXEL_PATTERN_YCRYCB (0x5)
> +#define CFG_PIXEL_PATTERN_CBYCRY (0x6)
> +#define CFG_PIXEL_PATTERN_CRYCBY (0x7)
> +#define CFG_COMPOSITE_REG_UPDATE_EN BIT(4)
> +
> +#define VFE_IRQ_CMD (0x058)
> +#define CMD_GLOBAL_CLEAR BIT(0)
> +
> +#define VFE_IRQ_MASK_0 (0x05c)
> +#define MASK_0_CAMIF_SOF BIT(0)
> +#define MASK_0_CAMIF_EOF BIT(1)
> +#define MASK_0_RDIn_REG_UPDATE(n) BIT((n) + 5)
> +#define MASK_0_line_n_REG_UPDATE(n) \
> + ((n) == VFE_LINE_PIX ? \
> + BIT(4) : MASK_0_RDIn_REG_UPDATE(n))
> +#define MASK_0_IMAGE_MASTER_n_PING_PONG(n) BIT((n) + 8)
> +#define MASK_0_IMAGE_COMPOSITE_DONE_n(n) BIT((n) + 25)
> +#define MASK_0_RESET_ACK BIT(31)
> +
> +#define VFE_IRQ_MASK_1 (0x060)
> +#define MASK_1_CAMIF_ERROR BIT(0)
> +#define MASK_1_VIOLATION BIT(7)
> +#define MASK_1_BUS_BDG_HALT_ACK BIT(8)
> +#define MASK_1_IMAGE_MASTER_n_BUS_OVERFLOW(n) BIT((n) + 9)
> +#define MASK_1_RDIn_SOF(n) BIT((n) + 29)
> +
> +#define VFE_IRQ_CLEAR_0 (0x064)
> +#define VFE_IRQ_CLEAR_1 (0x068)
> +
> +#define VFE_IRQ_STATUS_0 (0x06c)
> +#define STATUS_0_CAMIF_SOF BIT(0)
> +#define STATUS_0_RDIn_REG_UPDATE(n) BIT((n) + 5)
> +#define STATUS_0_line_n_REG_UPDATE(n) \
> + ((n) == VFE_LINE_PIX ? \
> + BIT(4) : STATUS_0_RDIn_REG_UPDATE(n))
> +#define STATUS_0_IMAGE_MASTER_n_PING_PONG(n) BIT((n) + 8)
> +#define STATUS_0_IMAGE_COMPOSITE_DONE_n(n) BIT((n) + 25)
> +#define STATUS_0_RESET_ACK BIT(31)
> +
> +#define VFE_IRQ_STATUS_1 (0x070)
> +#define STATUS_1_VIOLATION BIT(7)
> +#define STATUS_1_BUS_BDG_HALT_ACK BIT(8)
> +#define STATUS_1_RDIn_SOF(n) BIT((n) + 27)
> +
> +#define VFE_VIOLATION_STATUS (0x07c)
> +
> +#define VFE_CAMIF_CMD (0x478)
> +#define CMD_CLEAR_CAMIF_STATUS BIT(2)
> +
> +#define VFE_CAMIF_CFG (0x47c)
> +#define CFG_VSYNC_SYNC_EDGE (0)
> +#define VSYNC_ACTIVE_HIGH (0)
> +#define VSYNC_ACTIVE_LOW (1)
> +#define CFG_HSYNC_SYNC_EDGE (1)
> +#define HSYNC_ACTIVE_HIGH (0)
> +#define HSYNC_ACTIVE_LOW (1)
> +#define CFG_VFE_SUBSAMPLE_ENABLE BIT(4)
> +#define CFG_BUS_SUBSAMPLE_ENABLE BIT(5)
> +#define CFG_VFE_OUTPUT_EN BIT(6)
> +#define CFG_BUS_OUTPUT_EN BIT(7)
> +#define CFG_BINNING_EN BIT(9)
> +#define CFG_FRAME_BASED_EN BIT(10)
> +#define CFG_RAW_CROP_EN BIT(22)
> +
> +// XXX different, don't exist in TITAN register docs
> +#define VFE_0_CAMIF_FRAME_CFG 0x484
> +#define VFE_0_CAMIF_WINDOW_WIDTH_CFG 0x488
> +#define VFE_0_CAMIF_WINDOW_HEIGHT_CFG 0x48c
> +#define VFE_0_CAMIF_SUBSAMPLE_CFG 0x490
> +#define VFE_0_CAMIF_IRQ_FRAMEDROP_PATTERN 0x498
> +#define VFE_0_CAMIF_IRQ_SUBSAMPLE_PATTERN 0x49c
> +#define VFE_0_CAMIF_STATUS 0x4a4
> +#define VFE_0_CAMIF_STATUS_HALT BIT(31)
> +#define CAMIF_TIMEOUT_SLEEP_US 1000
> +#define CAMIF_TIMEOUT_ALL_US 1000000
> +
> +#define VFE_REG_UPDATE_CMD (0x4ac)
> +#define REG_UPDATE_RDIn(n) BIT(1 + (n))
> +#define REG_UPDATE_line_n(n) \
> + ((n) == VFE_LINE_PIX ? 1 : REG_UPDATE_RDIn(n))
> +
> +
> +#define VFE_BUS_IRQ_MASK(n) (0x2044 + (n) * 4)
> +#define VFE_BUS_IRQ_CLEAR(n) (0x2050 + (n) * 4)
> +
> +#define VFE_BUS_IRQ_STATUS(n) (0x205c + (n) * 4)
> +#define STATUS0_COMP_RESET_DONE BIT(0)
> +#define STATUS0_COMP_REG_UPDATE0_DONE BIT(1)
> +#define STATUS0_COMP_REG_UPDATE1_DONE BIT(2)
> +#define STATUS0_COMP_REG_UPDATE2_DONE BIT(3)
> +#define STATUS0_COMP_REG_UPDATE3_DONE BIT(4)
> +#define STATUS0_COMP_REG_UPDATE_DONE(n) BIT(n + 1)
> +#define STATUS0_COMP0_BUF_DONE BIT(5)
> +#define STATUS0_COMP1_BUF_DONE BIT(6)
> +#define STATUS0_COMP2_BUF_DONE BIT(7)
> +#define STATUS0_COMP3_BUF_DONE BIT(8)
> +#define STATUS0_COMP4_BUF_DONE BIT(9)
> +#define STATUS0_COMP5_BUF_DONE BIT(10)
> +#define STATUS0_COMP_BUF_DONE(n) BIT(n + 5)
> +#define STATUS0_COMP_ERROR BIT(11)
> +#define STATUS0_COMP_OVERWRITE BIT(12)
> +#define STATUS0_OVERFLOW BIT(13)
> +#define STATUS0_VIOLATION BIT(14)
> +/* WM_CLIENT_BUF_DONE defined for buffers 0:19 */
> +#define STATUS1_WM_CLIENT_BUF_DONE(n) BIT(n)
> +#define STATUS1_EARLY_DONE BIT(24)
> +#define STATUS2_DUAL_COMP0_BUF_DONE BIT(0)
> +#define STATUS2_DUAL_COMP1_BUF_DONE BIT(1)
> +#define STATUS2_DUAL_COMP2_BUF_DONE BIT(2)
> +#define STATUS2_DUAL_COMP3_BUF_DONE BIT(3)
> +#define STATUS2_DUAL_COMP4_BUF_DONE BIT(4)
> +#define STATUS2_DUAL_COMP5_BUF_DONE BIT(5)
> +#define STATUS2_DUAL_COMP_BUF_DONE(n) BIT(n)
> +#define STATUS2_DUAL_COMP_ERROR BIT(6)
> +#define STATUS2_DUAL_COMP_OVERWRITE BIT(7)
> +
> +#define VFE_BUS_IRQ_CLEAR_GLOBAL (0x2068)
> +
> +#define VFE_BUS_WM_DEBUG_STATUS_CFG (0x226c)
> +#define DEBUG_STATUS_CFG_STATUS0(n) BIT(n)
> +#define DEBUG_STATUS_CFG_STATUS1(n) BIT(8+n)
> +
> +#define VFE_BUS_WM_ADDR_SYNC_FRAME_HEADER (0x2080)
> +
> +#define VFE_BUS_WM_ADDR_SYNC_NO_SYNC (0x2084)
> +#define BUS_VER2_MAX_CLIENTS (24)
> +#define WM_ADDR_NO_SYNC_DEFAULT_VAL \
> + ((1 << BUS_VER2_MAX_CLIENTS) - 1)
> +
> +#define VFE_BUS_WM_CGC_OVERRIDE (0x200c)
> +#define WM_CGC_OVERRIDE_ALL (0xFFFFF)
> +
> +#define VFE_BUS_WM_TEST_BUS_CTRL (0x211c)
> +
> +#define VFE_BUS_WM_STATUS0(n) (0x2200 + (n) * 0x100)
> +#define VFE_BUS_WM_STATUS1(n) (0x2204 + (n) * 0x100)
> +#define VFE_BUS_WM_CFG(n) (0x2208 + (n) * 0x100)
> +#define WM_CFG_EN (0)
> +#define WM_CFG_MODE (1)
> +#define MODE_QCOM_PLAIN (0)
> +#define MODE_MIPI_RAW (1)
> +#define WM_CFG_VIRTUALFRAME (2)
> +#define VFE_BUS_WM_HEADER_ADDR(n) (0x220c + (n) * 0x100)
> +#define VFE_BUS_WM_HEADER_CFG(n) (0x2210 + (n) * 0x100)
> +#define VFE_BUS_WM_IMAGE_ADDR(n) (0x2214 + (n) * 0x100)
> +#define VFE_BUS_WM_IMAGE_ADDR_OFFSET(n) (0x2218 + (n) * 0x100)
> +#define VFE_BUS_WM_BUFFER_WIDTH_CFG(n) (0x221c + (n) * 0x100)
> +#define WM_BUFFER_DEFAULT_WIDTH (0xFF01)
> +
> +#define VFE_BUS_WM_BUFFER_HEIGHT_CFG(n) (0x2220 + (n) * 0x100)
> +#define VFE_BUS_WM_PACKER_CFG(n) (0x2224 + (n) * 0x100)
> +
> +#define VFE_BUS_WM_STRIDE(n) (0x2228 + (n) * 0x100)
> +#define WM_STRIDE_DEFAULT_STRIDE (0xFF01)
> +
> +#define VFE_BUS_WM_IRQ_SUBSAMPLE_PERIOD(n) (0x2248 + (n) * 0x100)
> +#define VFE_BUS_WM_IRQ_SUBSAMPLE_PATTERN(n) (0x224c + (n) * 0x100)
> +#define VFE_BUS_WM_FRAMEDROP_PERIOD(n) (0x2250 + (n) * 0x100)
> +#define VFE_BUS_WM_FRAMEDROP_PATTERN(n) (0x2254 + (n) * 0x100)
> +#define VFE_BUS_WM_FRAME_INC(n) (0x2258 + (n) * 0x100)
> +#define VFE_BUS_WM_BURST_LIMIT(n) (0x225c + (n) * 0x100)
> +
> +
> +static void vfe_hw_version_read(struct vfe_device *vfe, struct device *dev)
> +{
> + u32 hw_version = readl_relaxed(vfe->base + VFE_HW_VERSION);
> +
> + u32 gen = (hw_version >> 28) & 0xF;
> + u32 rev = (hw_version >> 16) & 0xFFF;
> + u32 step = hw_version & 0xFFFF;
> +
> + dev_err(dev, "VFE HW Version = %u.%u.%u\n", gen, rev, step);
> +}
> +
> +static inline void vfe_reg_clr(struct vfe_device *vfe, u32 reg, u32 clr_bits)
> +{
> + u32 bits = readl_relaxed(vfe->base + reg);
> +
> + writel_relaxed(bits & ~clr_bits, vfe->base + reg);
> +}
> +
> +static inline void vfe_reg_set(struct vfe_device *vfe, u32 reg, u32 set_bits)
> +{
> + u32 bits = readl_relaxed(vfe->base + reg);
> +
> + writel_relaxed(bits | set_bits, vfe->base + reg);
> +}
> +
> +static void vfe_global_reset(struct vfe_device *vfe)
> +{
> + u32 reset_bits = GLOBAL_RESET_CMD_IDLE_CGC |
> + GLOBAL_RESET_CMD_DSP |
> + GLOBAL_RESET_CMD_TESTGEN |
> + GLOBAL_RESET_CMD_BUS_MISR |
> + GLOBAL_RESET_CMD_PM |
> + GLOBAL_RESET_CMD_REGISTER |
> + GLOBAL_RESET_CMD_BUS_BDG |
> + GLOBAL_RESET_CMD_BUS |
> + GLOBAL_RESET_CMD_CAMIF |
> + GLOBAL_RESET_CMD_CORE;
- the above settings are overwritten by this assignment:
> + reset_bits = 0x00003F9F;
> +
> + writel_relaxed(BIT(31), vfe->base + VFE_IRQ_MASK_0);
> +
> + /* Make sure IRQ mask has been written before resetting */
> + wmb();
> +
> + writel_relaxed(reset_bits, vfe->base + VFE_GLOBAL_RESET_CMD);
> +}
> +
> +static void vfe_wm_start(struct vfe_device *vfe, u8 wm, struct vfe_line *line)
> +{
> + u32 val;
> +
> + /*Set Debug Registers*/
> + val = DEBUG_STATUS_CFG_STATUS0(1) |
> + DEBUG_STATUS_CFG_STATUS0(7);
> + writel_relaxed(val, vfe->base + VFE_BUS_WM_DEBUG_STATUS_CFG);
> +
> + /* BUS_WM_INPUT_IF_ADDR_SYNC_FRAME_HEADER */
> + writel_relaxed(0, vfe->base + VFE_BUS_WM_ADDR_SYNC_FRAME_HEADER);
> +
> + /* no clock gating at bus input */
> + val = WM_CGC_OVERRIDE_ALL;
> + writel_relaxed(val, vfe->base + VFE_BUS_WM_CGC_OVERRIDE);
> +
> + writel_relaxed(0x0, vfe->base + VFE_BUS_WM_TEST_BUS_CTRL);
> +
> + /* if addr_no_sync has default value then config the addr no sync reg */
> + val = WM_ADDR_NO_SYNC_DEFAULT_VAL;
> + writel_relaxed(val, vfe->base + VFE_BUS_WM_ADDR_SYNC_NO_SYNC);
> +
> + writel_relaxed(0xf, vfe->base + VFE_BUS_WM_BURST_LIMIT(wm));
> +
> + val = WM_BUFFER_DEFAULT_WIDTH;
> + writel_relaxed(val, vfe->base + VFE_BUS_WM_BUFFER_WIDTH_CFG(wm));
> +
> + val = 0;
> + writel_relaxed(val, vfe->base + VFE_BUS_WM_BUFFER_HEIGHT_CFG(wm));
> +
> + val = 0;
> + writel_relaxed(val, vfe->base + VFE_BUS_WM_PACKER_CFG(wm)); // XXX 1 for PLAIN8?
- C++ style comment
Also here and in several comments below you use the XXX tag which looks
more confusing than helpful for me. Would it be possible to expand such comments
to make them more explicit? Just a nitpick though.
> +
> + /* Configure stride for RDIs */
> + //val = pix->plane_fmt[0].bytesperline;
- the commented out line should probably be removed. Or changed into real
comment.
Thanks,
Andrey
> + val = WM_STRIDE_DEFAULT_STRIDE;
> + writel_relaxed(val, vfe->base + VFE_BUS_WM_STRIDE(wm));
> +
> + /* Enable WM */
> + val = 1 << WM_CFG_EN |
> + MODE_MIPI_RAW << WM_CFG_MODE;
> + writel_relaxed(val, vfe->base + VFE_BUS_WM_CFG(wm));
> +}
> +
> +static void vfe_wm_stop(struct vfe_device *vfe, u8 wm)
> +{
> + /* Disable WM */
> + writel_relaxed(0, vfe->base + VFE_BUS_WM_CFG(wm));
> +}
> +
> +static void vfe_wm_update(struct vfe_device *vfe, u8 wm, u32 addr,
> + struct vfe_line *line)
> +{
> + /* XXX use cmdbuf for this ?? */
> + struct v4l2_pix_format_mplane *pix =
> + &line->video_out.active_fmt.fmt.pix_mp;
> + u32 stride = pix->plane_fmt[0].bytesperline;
> +
> + writel_relaxed(addr, vfe->base + VFE_BUS_WM_IMAGE_ADDR(wm));
> + writel_relaxed(stride * pix->height, vfe->base + VFE_BUS_WM_FRAME_INC(wm));
> +
> + /* XXX enable wm ? */
> +}
> +
> +static void vfe_reg_update(struct vfe_device *vfe, enum vfe_line_id line_id)
> +{
> + vfe->reg_update |= REG_UPDATE_line_n(line_id);
> +
> + /* Enforce ordering between previous reg writes and reg update */
> + wmb();
> +
> + writel_relaxed(vfe->reg_update, vfe->base + VFE_REG_UPDATE_CMD);
> +
> + /* Enforce ordering between reg update and subsequent reg writes */
> + wmb();
> +}
> +
> +static inline void vfe_reg_update_clear(struct vfe_device *vfe,
> + enum vfe_line_id line_id)
> +{
> + vfe->reg_update &= ~REG_UPDATE_line_n(line_id);
> +}
> +
> +static void vfe_enable_irq_common(struct vfe_device *vfe)
> +{
> + vfe_reg_set(vfe, VFE_IRQ_MASK_0, ~0u);
> + vfe_reg_set(vfe, VFE_IRQ_MASK_1, ~0u);
> +
> + writel_relaxed(~0u, vfe->base + VFE_BUS_IRQ_MASK(0));
> + writel_relaxed(~0u, vfe->base + VFE_BUS_IRQ_MASK(1));
> + writel_relaxed(~0u, vfe->base + VFE_BUS_IRQ_MASK(2));
> +}
> +
> +static void vfe_isr_halt_ack(struct vfe_device *vfe)
> +{
> + complete(&vfe->halt_complete);
> +}
> +
> +static void vfe_isr_read(struct vfe_device *vfe, u32 *status0, u32 *status1)
> +{
> + *status0 = readl_relaxed(vfe->base + VFE_IRQ_STATUS_0);
> + *status1 = readl_relaxed(vfe->base + VFE_IRQ_STATUS_1);
> +
> + writel_relaxed(*status0, vfe->base + VFE_IRQ_CLEAR_0);
> + writel_relaxed(*status1, vfe->base + VFE_IRQ_CLEAR_1);
> +
> + /* Enforce ordering between IRQ Clear and Global IRQ Clear */
> + wmb();
> + writel_relaxed(CMD_GLOBAL_CLEAR, vfe->base + VFE_IRQ_CMD);
> +}
> +
> +static void vfe_violation_read(struct vfe_device *vfe)
> +{
> + u32 violation = readl_relaxed(vfe->base + VFE_VIOLATION_STATUS);
> +
> + pr_err_ratelimited("VFE: violation = 0x%08x\n", violation);
> +}
> +
> +/*
> + * vfe_isr - VFE module interrupt handler
> + * @irq: Interrupt line
> + * @dev: VFE device
> + *
> + * Return IRQ_HANDLED on success
> + */
> +static irqreturn_t vfe_isr(int irq, void *dev)
> +{
> + struct vfe_device *vfe = dev;
> + u32 status0, status1, vfe_bus_status[3];
> + int i, wm;
> +
> + status0 = readl_relaxed(vfe->base + VFE_IRQ_STATUS_0);
> + status1 = readl_relaxed(vfe->base + VFE_IRQ_STATUS_1);
> +
> + writel_relaxed(status0, vfe->base + VFE_IRQ_CLEAR_0);
> + writel_relaxed(status1, vfe->base + VFE_IRQ_CLEAR_1);
> +
> + for (i = VFE_LINE_RDI0; i <= VFE_LINE_RDI2; i++) {
> + vfe_bus_status[i] = readl_relaxed(vfe->base + VFE_BUS_IRQ_STATUS(i));
> + writel_relaxed(vfe_bus_status[i], vfe->base + VFE_BUS_IRQ_CLEAR(i));
> + }
> +
> + /* Enforce ordering between IRQ reading and interpretation */
> + wmb();
> +
> + writel_relaxed(CMD_GLOBAL_CLEAR, vfe->base + VFE_IRQ_CMD);
> + writel_relaxed(1, vfe->base + VFE_BUS_IRQ_CLEAR_GLOBAL);
> +
> + if (status0 & STATUS_0_RESET_ACK)
> + vfe->isr_ops.reset_ack(vfe);
> +
> + for (i = VFE_LINE_RDI0; i <= VFE_LINE_PIX; i++)
> + if (status0 & STATUS_0_line_n_REG_UPDATE(i))
> + vfe->isr_ops.reg_update(vfe, i);
> +
> + for (i = VFE_LINE_RDI0; i <= VFE_LINE_RDI2; i++)
> + if (status0 & STATUS_1_RDIn_SOF(i))
> + vfe->isr_ops.sof(vfe, i);
> +
> + for (i = 0; i < MSM_VFE_COMPOSITE_IRQ_NUM; i++)
> + if (vfe_bus_status[0] & STATUS0_COMP_BUF_DONE(i))
> + vfe->isr_ops.comp_done(vfe, i);
> +
> + for (wm = 0; wm < MSM_VFE_IMAGE_MASTERS_NUM; wm++)
> + if (status0 & BIT(9))
> + if (vfe_bus_status[1] & STATUS1_WM_CLIENT_BUF_DONE(wm))
> + vfe->isr_ops.wm_done(vfe, wm);
> +
> + return IRQ_HANDLED;
> +}
> +
> +/*
> + * vfe_halt - Trigger halt on VFE module and wait to complete
> + * @vfe: VFE device
> + *
> + * Return 0 on success or a negative error code otherwise
> + */
> +static int vfe_halt(struct vfe_device *vfe)
> +{
> + unsigned long time;
> +
> + return 0;
> +
> + reinit_completion(&vfe->halt_complete);
> +
> + time = wait_for_completion_timeout(&vfe->halt_complete,
> + msecs_to_jiffies(VFE_HALT_TIMEOUT_MS));
> + if (!time) {
> + dev_err(vfe->camss->dev, "VFE halt timeout\n");
> + return -EIO;
> + }
> +
> + return 0;
> +}
> +
> +static int vfe_get_output(struct vfe_line *line)
> +{
> + struct vfe_device *vfe = to_vfe(line);
> + struct vfe_output *output;
> + struct v4l2_format *f = &line->video_out.active_fmt;
> + unsigned long flags;
> + int i;
> + int wm_idx;
> +
> + spin_lock_irqsave(&vfe->output_lock, flags);
> +
> + output = &line->output;
> + if (output->state != VFE_OUTPUT_OFF) {
> + dev_err(vfe->camss->dev, "Output is running\n");
> + goto error;
> + }
> +
> + switch (f->fmt.pix_mp.pixelformat) {
> + case V4L2_PIX_FMT_NV12:
> + case V4L2_PIX_FMT_NV21:
> + case V4L2_PIX_FMT_NV16:
> + case V4L2_PIX_FMT_NV61:
> + output->wm_num = 2;
> + break;
> + default:
> + output->wm_num = 1;
> + break;
> + }
> +
> + for (i = 0; i < output->wm_num; i++) {
> + wm_idx = vfe_reserve_wm(vfe, line->id);
> + if (wm_idx < 0) {
> + dev_err(vfe->camss->dev, "Can not reserve wm\n");
> + goto error_get_wm;
> + }
> + output->wm_idx[i] = wm_idx;
> + }
> +
> + output->drop_update_idx = 0;
> +
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> +
> + return 0;
> +
> +error_get_wm:
> + for (i--; i >= 0; i--)
> + vfe_release_wm(vfe, output->wm_idx[i]);
> + output->state = VFE_OUTPUT_OFF;
> +error:
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> +
> + return -EINVAL;
> +}
> +
> +static int vfe_enable_output(struct vfe_line *line)
> +{
> + struct vfe_device *vfe = to_vfe(line);
> + struct vfe_output *output = &line->output;
> + const struct vfe_hw_ops *ops = vfe->ops;
> + struct media_entity *sensor;
> + unsigned long flags;
> + unsigned int frame_skip = 0;
> + unsigned int i;
> +
> + sensor = camss_find_sensor(&line->subdev.entity);
> + if (sensor) {
> + struct v4l2_subdev *subdev =
> + media_entity_to_v4l2_subdev(sensor);
> +
> + v4l2_subdev_call(subdev, sensor, g_skip_frames, &frame_skip);
> + /* Max frame skip is 29 frames */
> + if (frame_skip > VFE_FRAME_DROP_VAL - 1)
> + frame_skip = VFE_FRAME_DROP_VAL - 1;
> + }
> +
> + spin_lock_irqsave(&vfe->output_lock, flags);
> +
> + ops->reg_update_clear(vfe, line->id);
> +
> + if (output->state != VFE_OUTPUT_OFF) {
> + dev_err(vfe->camss->dev, "Output is not in reserved state %d\n",
> + output->state);
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> + return -EINVAL;
> + }
> +
> + WARN_ON(output->gen2.active_num);
> +
> + output->state = VFE_OUTPUT_ON;
> +
> + output->sequence = 0;
> + output->wait_reg_update = 0;
> + reinit_completion(&output->reg_update);
> +
> + if (line->id != VFE_LINE_PIX)
> + vfe_wm_start(vfe, output->wm_idx[0], line);
> +
> + for (i = 0; i < 2; i++) {
> + output->buf[i] = vfe_buf_get_pending(output);
> + if (!output->buf[i])
> + break;
> + output->gen2.active_num++;
> + vfe_wm_update(vfe, output->wm_idx[0], output->buf[i]->addr[0], line);
> + }
> +
> + ops->reg_update(vfe, line->id);
> +
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> +
> + return 0;
> +}
> +
> +static int vfe_disable_output(struct vfe_line *line)
> +{
> + struct vfe_device *vfe = to_vfe(line);
> + struct vfe_output *output = &line->output;
> + unsigned long flags;
> + unsigned int i;
> + bool done;
> + int timeout = 0;
> +
> + do {
> + spin_lock_irqsave(&vfe->output_lock, flags);
> + done = !output->gen2.active_num;
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> + usleep_range(10000, 20000);
> +
> + if (timeout++ == 100) {
> + dev_err(vfe->camss->dev, "VFE idle timeout - resetting\n");
> + vfe_reset(vfe);
> + output->gen2.active_num = 0;
> + return 0;
> + }
> + } while (!done);
> +
> + spin_lock_irqsave(&vfe->output_lock, flags);
> + for (i = 0; i < output->wm_num; i++)
> + vfe_wm_stop(vfe, output->wm_idx[i]);
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> +
> + return 0;
> +}
> +
> +/*
> + * vfe_enable - Enable streaming on VFE line
> + * @line: VFE line
> + *
> + * Return 0 on success or a negative error code otherwise
> + */
> +static int vfe_enable(struct vfe_line *line)
> +{
> + struct vfe_device *vfe = to_vfe(line);
> + int ret;
> +
> + mutex_lock(&vfe->stream_lock);
> +
> + if (!vfe->stream_count)
> + vfe_enable_irq_common(vfe);
> +
> + vfe->stream_count++;
> +
> + mutex_unlock(&vfe->stream_lock);
> +
> + ret = vfe_get_output(line);
> + if (ret < 0)
> + goto error_get_output;
> +
> + ret = vfe_enable_output(line);
> + if (ret < 0)
> + goto error_enable_output;
> +
> + vfe->was_streaming = 1;
> +
> + return 0;
> +
> +
> +error_enable_output:
> + vfe_put_output(line);
> +
> +error_get_output:
> + mutex_lock(&vfe->stream_lock);
> +
> + vfe->stream_count--;
> +
> + mutex_unlock(&vfe->stream_lock);
> +
> + return ret;
> +}
> +
> +/*
> + * vfe_disable - Disable streaming on VFE line
> + * @line: VFE line
> + *
> + * Return 0 on success or a negative error code otherwise
> + */
> +static int vfe_disable(struct vfe_line *line)
> +{
> + struct vfe_device *vfe = to_vfe(line);
> +
> + vfe_disable_output(line);
> +
> + vfe_put_output(line);
> +
> + mutex_lock(&vfe->stream_lock);
> +
> + vfe->stream_count--;
> +
> + mutex_unlock(&vfe->stream_lock);
> +
> + return 0;
> +}
> +
> +/*
> + * vfe_isr_sof - Process start of frame interrupt
> + * @vfe: VFE Device
> + * @line_id: VFE line
> + */
> +static void vfe_isr_sof(struct vfe_device *vfe, enum vfe_line_id line_id)
> +{
> +
> +}
> +
> +/*
> + * vfe_isr_reg_update - Process reg update interrupt
> + * @vfe: VFE Device
> + * @line_id: VFE line
> + */
> +static void vfe_isr_reg_update(struct vfe_device *vfe, enum vfe_line_id line_id)
> +{
> + struct vfe_output *output;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&vfe->output_lock, flags);
> + vfe->ops->reg_update_clear(vfe, line_id);
> +
> + output = &vfe->line[line_id].output;
> +
> + if (output->wait_reg_update) {
> + output->wait_reg_update = 0;
> + complete(&output->reg_update);
> + }
> +
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> +}
> +
> +/*
> + * vfe_isr_wm_done - Process write master done interrupt
> + * @vfe: VFE Device
> + * @wm: Write master id
> + */
> +static void vfe_isr_wm_done(struct vfe_device *vfe, u8 wm)
> +{
> + struct vfe_line *line = &vfe->line[vfe->wm_output_map[wm]];
> + struct camss_buffer *ready_buf;
> + struct vfe_output *output;
> + unsigned long flags;
> + u32 index;
> + u64 ts = ktime_get_ns();
> +
> + spin_lock_irqsave(&vfe->output_lock, flags);
> +
> + if (vfe->wm_output_map[wm] == VFE_LINE_NONE) {
> + dev_err_ratelimited(vfe->camss->dev,
> + "Received wm done for unmapped index\n");
> + goto out_unlock;
> + }
> + output = &vfe->line[vfe->wm_output_map[wm]].output;
> +
> + ready_buf = output->buf[0];
> + if (!ready_buf) {
> + dev_err_ratelimited(vfe->camss->dev,
> + "Missing ready buf %d!\n", output->state);
> + goto out_unlock;
> + }
> +
> + ready_buf->vb.vb2_buf.timestamp = ts;
> + ready_buf->vb.sequence = output->sequence++;
> +
> + index = 0;
> + output->buf[0] = output->buf[1];
> + if (output->buf[0])
> + index = 1;
> +
> + output->buf[index] = vfe_buf_get_pending(output);
> +
> + if (output->buf[index])
> + vfe_wm_update(vfe, output->wm_idx[0], output->buf[index]->addr[0], line);
> + else
> + output->gen2.active_num--;
> +
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> +
> + vb2_buffer_done(&ready_buf->vb.vb2_buf, VB2_BUF_STATE_DONE);
> +
> + return;
> +
> +out_unlock:
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> +}
> +
> +/*
> + * vfe_queue_buffer - Add empty buffer
> + * @vid: Video device structure
> + * @buf: Buffer to be enqueued
> + *
> + * Add an empty buffer - depending on the current number of buffers it will be
> + * put in pending buffer queue or directly given to the hardware to be filled.
> + *
> + * Return 0 on success or a negative error code otherwise
> + */
> +static int vfe_queue_buffer(struct camss_video *vid,
> + struct camss_buffer *buf)
> +{
> + struct vfe_line *line = container_of(vid, struct vfe_line, video_out);
> + struct vfe_device *vfe = to_vfe(line);
> + struct vfe_output *output;
> + unsigned long flags;
> +
> + output = &line->output;
> +
> + spin_lock_irqsave(&vfe->output_lock, flags);
> +
> + if (output->state == VFE_OUTPUT_ON && output->gen2.active_num < 2) {
> + output->buf[output->gen2.active_num++] = buf;
> + vfe_wm_update(vfe, output->wm_idx[0], buf->addr[0], line);
> + } else {
> + vfe_buf_add_pending(output, buf);
> + }
> +
> + spin_unlock_irqrestore(&vfe->output_lock, flags);
> +
> + return 0;
> +}
> +
> +const struct vfe_isr_ops vfe_isr_ops_170 = {
> + .reset_ack = vfe_isr_reset_ack,
> + .halt_ack = vfe_isr_halt_ack,
> + .reg_update = vfe_isr_reg_update,
> + .sof = vfe_isr_sof,
> + .comp_done = vfe_isr_comp_done,
> + .wm_done = vfe_isr_wm_done,
> +};
> +
> +static const struct camss_video_ops vfe_video_ops_170 = {
> + .queue_buffer = vfe_queue_buffer,
> + .flush_buffers = vfe_flush_buffers,
> +};
> +
> +static void vfe_subdev_init(struct vfe_device *vfe)
> +{
> + vfe->isr_ops = vfe_isr_ops_170;
> + vfe->video_ops = vfe_video_ops_170;
> +}
> +
> +const struct vfe_hw_ops vfe_ops_170 = {
> + .global_reset = vfe_global_reset,
> + .hw_version_read = vfe_hw_version_read,
> + .isr_read = vfe_isr_read,
> + .isr = vfe_isr,
> + .reg_update_clear = vfe_reg_update_clear,
> + .reg_update = vfe_reg_update,
> + .subdev_init = vfe_subdev_init,
> + .vfe_disable = vfe_disable,
> + .vfe_enable = vfe_enable,
> + .vfe_halt = vfe_halt,
> + .violation_read = vfe_violation_read,
> +};
> +
> diff --git a/drivers/media/platform/qcom/camss/camss-vfe.c b/drivers/media/platform/qcom/camss/camss-vfe.c
> index 2ffa5b3c5426..5a874b544391 100644
> --- a/drivers/media/platform/qcom/camss/camss-vfe.c
> +++ b/drivers/media/platform/qcom/camss/camss-vfe.c
> @@ -96,6 +96,39 @@ static const struct vfe_format formats_pix_8x96[] = {
> { MEDIA_BUS_FMT_YVYU8_2X8, 8 },
> };
>
> +static const struct vfe_format formats_rdi_845[] = {
> + { MEDIA_BUS_FMT_UYVY8_2X8, 8 },
> + { MEDIA_BUS_FMT_VYUY8_2X8, 8 },
> + { MEDIA_BUS_FMT_YUYV8_2X8, 8 },
> + { MEDIA_BUS_FMT_YVYU8_2X8, 8 },
> + { MEDIA_BUS_FMT_SBGGR8_1X8, 8 },
> + { MEDIA_BUS_FMT_SGBRG8_1X8, 8 },
> + { MEDIA_BUS_FMT_SGRBG8_1X8, 8 },
> + { MEDIA_BUS_FMT_SRGGB8_1X8, 8 },
> + { MEDIA_BUS_FMT_SBGGR10_1X10, 10 },
> + { MEDIA_BUS_FMT_SGBRG10_1X10, 10 },
> + { MEDIA_BUS_FMT_SGRBG10_1X10, 10 },
> + { MEDIA_BUS_FMT_SRGGB10_1X10, 10 },
> + { MEDIA_BUS_FMT_SBGGR10_2X8_PADHI_LE, 16 },
> + { MEDIA_BUS_FMT_SBGGR12_1X12, 12 },
> + { MEDIA_BUS_FMT_SGBRG12_1X12, 12 },
> + { MEDIA_BUS_FMT_SGRBG12_1X12, 12 },
> + { MEDIA_BUS_FMT_SRGGB12_1X12, 12 },
> + { MEDIA_BUS_FMT_SBGGR14_1X14, 14 },
> + { MEDIA_BUS_FMT_SGBRG14_1X14, 14 },
> + { MEDIA_BUS_FMT_SGRBG14_1X14, 14 },
> + { MEDIA_BUS_FMT_SRGGB14_1X14, 14 },
> + { MEDIA_BUS_FMT_Y10_1X10, 10 },
> + { MEDIA_BUS_FMT_Y10_2X8_PADHI_LE, 16 },
> +};
> +
> +static const struct vfe_format formats_pix_845[] = {
> + { MEDIA_BUS_FMT_UYVY8_2X8, 8 },
> + { MEDIA_BUS_FMT_VYUY8_2X8, 8 },
> + { MEDIA_BUS_FMT_YUYV8_2X8, 8 },
> + { MEDIA_BUS_FMT_YVYU8_2X8, 8 },
> +};
> +
> /*
> * vfe_get_bpp - map media bus format to bits per pixel
> * @formats: supported media bus formats array
> @@ -192,7 +225,8 @@ static u32 vfe_src_pad_code(struct vfe_line *line, u32 sink_code,
> return sink_code;
> }
> else if (vfe->camss->version == CAMSS_8x96 ||
> - vfe->camss->version == CAMSS_660)
> + vfe->camss->version == CAMSS_660 ||
> + vfe->camss->version == CAMSS_845)
> switch (sink_code) {
> case MEDIA_BUS_FMT_YUYV8_2X8:
> {
> @@ -256,13 +290,7 @@ static u32 vfe_src_pad_code(struct vfe_line *line, u32 sink_code,
> return 0;
> }
>
> -/*
> - * vfe_reset - Trigger reset on VFE module and wait to complete
> - * @vfe: VFE device
> - *
> - * Return 0 on success or a negative error code otherwise
> - */
> -static int vfe_reset(struct vfe_device *vfe)
> +int vfe_reset(struct vfe_device *vfe)
> {
> unsigned long time;
>
> @@ -429,7 +457,8 @@ static int vfe_set_clock_rates(struct vfe_device *vfe)
> struct camss_clock *clock = &vfe->clock[i];
>
> if (!strcmp(clock->name, "vfe0") ||
> - !strcmp(clock->name, "vfe1")) {
> + !strcmp(clock->name, "vfe1") ||
> + !strcmp(clock->name, "vfe_lite")) {
> u64 min_rate = 0;
> long rate;
>
> @@ -1268,6 +1297,10 @@ int msm_vfe_subdev_init(struct camss *camss, struct vfe_device *vfe,
> case CAMSS_660:
> vfe->ops = &vfe_ops_4_8;
> break;
> +
> + case CAMSS_845:
> + vfe->ops = &vfe_ops_170;
> + break;
> default:
> return -EINVAL;
> }
> @@ -1379,6 +1412,14 @@ int msm_vfe_subdev_init(struct camss *camss, struct vfe_device *vfe,
> l->formats = formats_rdi_8x96;
> l->nformats = ARRAY_SIZE(formats_rdi_8x96);
> }
> + } else if (camss->version == CAMSS_845) {
> + if (i == VFE_LINE_PIX) {
> + l->formats = formats_pix_845;
> + l->nformats = ARRAY_SIZE(formats_pix_845);
> + } else {
> + l->formats = formats_rdi_845;
> + l->nformats = ARRAY_SIZE(formats_rdi_845);
> + }
> } else {
> return -EINVAL;
> }
> diff --git a/drivers/media/platform/qcom/camss/camss-vfe.h b/drivers/media/platform/qcom/camss/camss-vfe.h
> index 8629c833f130..a0b618c9cec8 100644
> --- a/drivers/media/platform/qcom/camss/camss-vfe.h
> +++ b/drivers/media/platform/qcom/camss/camss-vfe.h
> @@ -19,7 +19,6 @@
> #include "camss-video.h"
> #include "camss-vfe-gen1.h"
>
> -
> #define MSM_VFE_PAD_SINK 0
> #define MSM_VFE_PAD_SRC 1
> #define MSM_VFE_PADS_NUM 2
> @@ -39,14 +38,14 @@
> #define to_vfe(ptr_line) \
> container_of(vfe_line_array(ptr_line), struct vfe_device, line)
>
> -
> enum vfe_output_state {
> VFE_OUTPUT_OFF,
> VFE_OUTPUT_RESERVED,
> VFE_OUTPUT_SINGLE,
> VFE_OUTPUT_CONTINUOUS,
> VFE_OUTPUT_IDLE,
> - VFE_OUTPUT_STOPPING
> + VFE_OUTPUT_STOPPING,
> + VFE_OUTPUT_ON,
> };
>
> enum vfe_line_id {
> @@ -72,6 +71,9 @@ struct vfe_output {
> int active_buf;
> int wait_sof;
> } gen1;
> + struct {
> + int active_num;
> + } gen2;
> };
> enum vfe_output_state state;
> unsigned int sequence;
> @@ -169,14 +171,6 @@ void vfe_buf_add_pending(struct vfe_output *output, struct camss_buffer *buffer)
>
> struct camss_buffer *vfe_buf_get_pending(struct vfe_output *output);
>
> -/*
> - * vfe_disable - Disable streaming on VFE line
> - * @line: VFE line
> - *
> - * Return 0 on success or a negative error code otherwise
> - */
> -int vfe_disable(struct vfe_line *line);
> -
> int vfe_flush_buffers(struct camss_video *vid, enum vb2_buffer_state state);
>
> /*
> @@ -191,8 +185,17 @@ int vfe_put_output(struct vfe_line *line);
> int vfe_release_wm(struct vfe_device *vfe, u8 wm);
> int vfe_reserve_wm(struct vfe_device *vfe, enum vfe_line_id line_id);
>
> +/*
> + * vfe_reset - Trigger reset on VFE module and wait to complete
> + * @vfe: VFE device
> + *
> + * Return 0 on success or a negative error code otherwise
> + */
> +int vfe_reset(struct vfe_device *vfe);
> +
> extern const struct vfe_hw_ops vfe_ops_4_1;
> extern const struct vfe_hw_ops vfe_ops_4_7;
> extern const struct vfe_hw_ops vfe_ops_4_8;
> +extern const struct vfe_hw_ops vfe_ops_170;
>
> #endif /* QC_MSM_CAMSS_VFE_H */
> diff --git a/drivers/media/platform/qcom/camss/camss-video.c b/drivers/media/platform/qcom/camss/camss-video.c
> index bd9334af1c73..b4943df9eaf6 100644
> --- a/drivers/media/platform/qcom/camss/camss-video.c
> +++ b/drivers/media/platform/qcom/camss/camss-video.c
> @@ -133,6 +133,55 @@ static const struct camss_format_info formats_rdi_8x96[] = {
> { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> };
>
> +static const struct camss_format_info formats_rdi_845[] = {
> + { MEDIA_BUS_FMT_UYVY8_2X8, V4L2_PIX_FMT_UYVY, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> + { MEDIA_BUS_FMT_VYUY8_2X8, V4L2_PIX_FMT_VYUY, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> + { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_PIX_FMT_YUYV, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> + { MEDIA_BUS_FMT_YVYU8_2X8, V4L2_PIX_FMT_YVYU, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> + { MEDIA_BUS_FMT_SBGGR8_1X8, V4L2_PIX_FMT_SBGGR8, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 8 } },
> + { MEDIA_BUS_FMT_SGBRG8_1X8, V4L2_PIX_FMT_SGBRG8, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 8 } },
> + { MEDIA_BUS_FMT_SGRBG8_1X8, V4L2_PIX_FMT_SGRBG8, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 8 } },
> + { MEDIA_BUS_FMT_SRGGB8_1X8, V4L2_PIX_FMT_SRGGB8, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 8 } },
> + { MEDIA_BUS_FMT_SBGGR10_1X10, V4L2_PIX_FMT_SBGGR10P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 10 } },
> + { MEDIA_BUS_FMT_SGBRG10_1X10, V4L2_PIX_FMT_SGBRG10P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 10 } },
> + { MEDIA_BUS_FMT_SGRBG10_1X10, V4L2_PIX_FMT_SGRBG10P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 10 } },
> + { MEDIA_BUS_FMT_SRGGB10_1X10, V4L2_PIX_FMT_SRGGB10P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 10 } },
> + { MEDIA_BUS_FMT_SBGGR10_2X8_PADHI_LE, V4L2_PIX_FMT_SBGGR10, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> + { MEDIA_BUS_FMT_SBGGR12_1X12, V4L2_PIX_FMT_SBGGR12P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 12 } },
> + { MEDIA_BUS_FMT_SGBRG12_1X12, V4L2_PIX_FMT_SGBRG12P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 12 } },
> + { MEDIA_BUS_FMT_SGRBG12_1X12, V4L2_PIX_FMT_SGRBG12P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 12 } },
> + { MEDIA_BUS_FMT_SRGGB12_1X12, V4L2_PIX_FMT_SRGGB12P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 12 } },
> + { MEDIA_BUS_FMT_SBGGR14_1X14, V4L2_PIX_FMT_SBGGR14P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 14 } },
> + { MEDIA_BUS_FMT_SGBRG14_1X14, V4L2_PIX_FMT_SGBRG14P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 14 } },
> + { MEDIA_BUS_FMT_SGRBG14_1X14, V4L2_PIX_FMT_SGRBG14P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 14 } },
> + { MEDIA_BUS_FMT_SRGGB14_1X14, V4L2_PIX_FMT_SRGGB14P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 14 } },
> + { MEDIA_BUS_FMT_Y10_1X10, V4L2_PIX_FMT_Y10P, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 10 } },
> + { MEDIA_BUS_FMT_Y10_2X8_PADHI_LE, V4L2_PIX_FMT_Y10, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> +};
> +
> static const struct camss_format_info formats_pix_8x16[] = {
> { MEDIA_BUS_FMT_YUYV8_1_5X8, V4L2_PIX_FMT_NV12, 1,
> { { 1, 1 } }, { { 2, 3 } }, { 8 } },
> @@ -211,6 +260,49 @@ static const struct camss_format_info formats_pix_8x96[] = {
> { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> };
>
> +static const struct camss_format_info formats_pix_845[] = {
> + { MEDIA_BUS_FMT_YUYV8_1_5X8, V4L2_PIX_FMT_NV12, 1,
> + { { 1, 1 } }, { { 2, 3 } }, { 8 } },
> + { MEDIA_BUS_FMT_YVYU8_1_5X8, V4L2_PIX_FMT_NV12, 1,
> + { { 1, 1 } }, { { 2, 3 } }, { 8 } },
> + { MEDIA_BUS_FMT_UYVY8_1_5X8, V4L2_PIX_FMT_NV12, 1,
> + { { 1, 1 } }, { { 2, 3 } }, { 8 } },
> + { MEDIA_BUS_FMT_VYUY8_1_5X8, V4L2_PIX_FMT_NV12, 1,
> + { { 1, 1 } }, { { 2, 3 } }, { 8 } },
> + { MEDIA_BUS_FMT_YUYV8_1_5X8, V4L2_PIX_FMT_NV21, 1,
> + { { 1, 1 } }, { { 2, 3 } }, { 8 } },
> + { MEDIA_BUS_FMT_YVYU8_1_5X8, V4L2_PIX_FMT_NV21, 1,
> + { { 1, 1 } }, { { 2, 3 } }, { 8 } },
> + { MEDIA_BUS_FMT_UYVY8_1_5X8, V4L2_PIX_FMT_NV21, 1,
> + { { 1, 1 } }, { { 2, 3 } }, { 8 } },
> + { MEDIA_BUS_FMT_VYUY8_1_5X8, V4L2_PIX_FMT_NV21, 1,
> + { { 1, 1 } }, { { 2, 3 } }, { 8 } },
> + { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_PIX_FMT_NV16, 1,
> + { { 1, 1 } }, { { 1, 2 } }, { 8 } },
> + { MEDIA_BUS_FMT_YVYU8_2X8, V4L2_PIX_FMT_NV16, 1,
> + { { 1, 1 } }, { { 1, 2 } }, { 8 } },
> + { MEDIA_BUS_FMT_UYVY8_2X8, V4L2_PIX_FMT_NV16, 1,
> + { { 1, 1 } }, { { 1, 2 } }, { 8 } },
> + { MEDIA_BUS_FMT_VYUY8_2X8, V4L2_PIX_FMT_NV16, 1,
> + { { 1, 1 } }, { { 1, 2 } }, { 8 } },
> + { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_PIX_FMT_NV61, 1,
> + { { 1, 1 } }, { { 1, 2 } }, { 8 } },
> + { MEDIA_BUS_FMT_YVYU8_2X8, V4L2_PIX_FMT_NV61, 1,
> + { { 1, 1 } }, { { 1, 2 } }, { 8 } },
> + { MEDIA_BUS_FMT_UYVY8_2X8, V4L2_PIX_FMT_NV61, 1,
> + { { 1, 1 } }, { { 1, 2 } }, { 8 } },
> + { MEDIA_BUS_FMT_VYUY8_2X8, V4L2_PIX_FMT_NV61, 1,
> + { { 1, 1 } }, { { 1, 2 } }, { 8 } },
> + { MEDIA_BUS_FMT_UYVY8_2X8, V4L2_PIX_FMT_UYVY, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> + { MEDIA_BUS_FMT_VYUY8_2X8, V4L2_PIX_FMT_VYUY, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> + { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_PIX_FMT_YUYV, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> + { MEDIA_BUS_FMT_YVYU8_2X8, V4L2_PIX_FMT_YVYU, 1,
> + { { 1, 1 } }, { { 1, 1 } }, { 16 } },
> +};
> +
> /* -----------------------------------------------------------------------------
> * Helper functions
> */
> @@ -960,6 +1052,14 @@ int msm_video_register(struct camss_video *video, struct v4l2_device *v4l2_dev,
> video->formats = formats_rdi_8x96;
> video->nformats = ARRAY_SIZE(formats_rdi_8x96);
> }
> + } else if (video->camss->version == CAMSS_845) {
> + if (is_pix) {
> + video->formats = formats_pix_845;
> + video->nformats = ARRAY_SIZE(formats_pix_845);
> + } else {
> + video->formats = formats_rdi_845;
> + video->nformats = ARRAY_SIZE(formats_rdi_845);
> + }
> } else {
> goto error_video_register;
> }
> diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
> index aeec59bc6194..1c3d64d612ff 100644
> --- a/drivers/media/platform/qcom/camss/camss.c
> +++ b/drivers/media/platform/qcom/camss/camss.c
> @@ -465,6 +465,67 @@ static const struct resources vfe_res_660[] = {
> }
> };
>
> +static const struct resources vfe_res_845[] = {
> + /* VFE0 */
> + {
> + .regulator = { NULL },
> + .clock = { "camnoc_axi", "cpas_ahb", "slow_ahb_src",
> + "soc_ahb", "vfe0", "vfe0_axi",
> + "vfe0_src", "csi0",
> + "csi0_src"},
> + .clock_rate = { { 0 },
> + { 0 },
> + { 80000000 },
> + { 0 },
> + { 19200000, 100000000, 320000000, 404000000, 480000000, 600000000 },
> + { 0 },
> + { 320000000 },
> + { 19200000, 75000000, 384000000, 538666667 },
> + { 384000000 } },
> + .reg = { "vfe0" },
> + .interrupt = { "vfe0" }
> + },
> +
> + /* VFE1 */
> + {
> + .regulator = { NULL },
> + .clock = { "camnoc_axi", "cpas_ahb", "slow_ahb_src",
> + "soc_ahb", "vfe1", "vfe1_axi",
> + "vfe1_src", "csi1",
> + "csi1_src"},
> + .clock_rate = { { 0 },
> + { 0 },
> + { 80000000 },
> + { 0 },
> + { 19200000, 100000000, 320000000, 404000000, 480000000, 600000000 },
> + { 0 },
> + { 320000000 },
> + { 19200000, 75000000, 384000000, 538666667 },
> + { 384000000 } },
> + .reg = { "vfe1" },
> + .interrupt = { "vfe1" }
> + },
> +
> + /* VFE-lite */
> + {
> + .regulator = { NULL },
> + .clock = { "camnoc_axi", "cpas_ahb", "slow_ahb_src",
> + "soc_ahb", "vfe_lite",
> + "vfe_lite_src", "csi2",
> + "csi2_src"},
> + .clock_rate = { { 0 },
> + { 0 },
> + { 80000000 },
> + { 0 },
> + { 19200000, 100000000, 320000000, 404000000, 480000000, 600000000 },
> + { 320000000 },
> + { 19200000, 75000000, 384000000, 538666667 },
> + { 384000000 } },
> + .reg = { "vfe_lite" },
> + .interrupt = { "vfe_lite" }
> + }
> +};
> +
> /*
> * camss_add_clock_margin - Add margin to clock frequency rate
> * @rate: Clock frequency rate
>
More information about the linux-arm-kernel
mailing list