[PATCH v3 1/2] arm64: dts: mt8183: config dsi node

[Enric Balletbo i Serra]

Hi Hsin-Yi,

Thank you for the patch.

On 13/1/21 7:28, Hsin-Yi Wang wrote:
> Config dsi node for mt8183 kukui. Set panel and ports.
> 
> Several kukui boards share the same panel property and only compatible
> is different. So compatible will be set in board dts for comparison
> convenience.
> 
> Signed-off-by: Hsin-Yi Wang <hsinyi at chromium.org>
> Reviewed-by: Nicolas Boichat <drinkcat at chromium.org>
> ---
>  .../mediatek/mt8183-kukui-krane-sku176.dts    |  5 +++
>  .../arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 37 +++++++++++++++++++
>  2 files changed, 42 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
> index 47113e275cb52..721d16f9c3b4f 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts
> @@ -16,3 +16,8 @@ / {
>  	model = "MediaTek krane sku176 board";
>  	compatible = "google,krane-sku176", "google,krane", "mediatek,mt8183";
>  };
> +
> +&panel {
> +        status = "okay";
> +        compatible = "boe,tv101wum-nl6";
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
> index bf2ad1294dd30..c5f41b94f154e 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
> @@ -249,6 +249,35 @@ &cpu7 {
>  	proc-supply = <&mt6358_vproc11_reg>;
>  };
>  
> +&dsi0 {
> +	status = "okay";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	panel: panel at 0 {
> +		/* compatible will be set in board dts */
> +		reg = <0>;
> +		enable-gpios = <&pio 45 0>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&panel_pins_default>;
> +		avdd-supply = <&ppvarn_lcd>;
> +		avee-supply = <&ppvarp_lcd>;
> +		pp1800-supply = <&pp1800_lcd>;

It'd make sense to add also the backlight here?

+               backlight = <&backlight_lcd0>;

> +		port {
> +			panel_in: endpoint {
> +				remote-endpoint = <&dsi_out>;
> +			};
> +		};
> +	};
> +
> +	ports {
> +		port {
> +			dsi_out: endpoint {
> +				remote-endpoint = <&panel_in>;
> +			};
> +		};
> +	};
> +};
> +

I think you should enable the MIPI TX to have DSI and panel working?

+&mipi_tx0 {
+       status = "okay";
+};


>  &i2c0 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&i2c0_pins>;
> @@ -547,6 +576,14 @@ pins_clk {
>  		};
>  	};
>  
> +	panel_pins_default: panel_pins_default {
> +		panel_reset {
> +			pinmux = <PINMUX_GPIO45__FUNC_GPIO45>;
> +			output-low;
> +			bias-pull-up;
> +		};
> +	};
> +
>  	pwm0_pin_default: pwm0_pin_default {
>  		pins1 {
>  			pinmux = <PINMUX_GPIO176__FUNC_GPIO176>;
>