[PATCH 3/5] ARM: dts: meson8: add the thermal-zones with cooling configuration

[Neil Armstrong]

On 21/12/2020 19:13, Martin Blumenstingl wrote:
> The vendor kernel uses the following thermal-zone settings:
> <= 70°C:
> - CPU frequency limited to 1.608GHz
> - GPU limited to 511MHz and 5 cores (pixel processors)
> 
> <= 80°C:
> - CPU frequency limited to 1.2GHz
> - GPU limited to 435MHz and 4 cores (pixel processors)
> 
> <= 90°C:
> - CPU frequency limited to 0.804GHz
> - GPU limited to 328MHz and 3 cores (pixel processors)
> 
> Add simplified thermal configuration which is taken from the
> GXBB/GXL/GXM SoC family (which uses the same manufacturing process and
> has the same maximum junction temperature of 125°C). With this the
> thermal framework will try to keep the SoC temperature at or below 80°C
> which is identical to the vendor kernel (with the exception of one GPU
> pixel processor).
> 
> The number of GPU cores are not taken into account as this is not
> supported.
> 
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> ---
>  arch/arm/boot/dts/meson8.dtsi | 54 +++++++++++++++++++++++++++++++++++
>  1 file changed, 54 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
> index 04688e8abce2..420324ea2ad7 100644
> --- a/arch/arm/boot/dts/meson8.dtsi
> +++ b/arch/arm/boot/dts/meson8.dtsi
> @@ -9,6 +9,7 @@
>  #include <dt-bindings/power/meson8-power.h>
>  #include <dt-bindings/reset/amlogic,meson8b-clkc-reset.h>
>  #include <dt-bindings/reset/amlogic,meson8b-reset.h>
> +#include <dt-bindings/thermal/thermal.h>
>  #include "meson.dtsi"
>  
>  / {
> @@ -28,6 +29,7 @@ cpu0: cpu at 200 {
>  			resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>;
>  			operating-points-v2 = <&cpu_opp_table>;
>  			clocks = <&clkc CLKID_CPUCLK>;
> +			#cooling-cells = <2>; /* min followed by max */
>  		};
>  
>  		cpu1: cpu at 201 {
> @@ -39,6 +41,7 @@ cpu1: cpu at 201 {
>  			resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>;
>  			operating-points-v2 = <&cpu_opp_table>;
>  			clocks = <&clkc CLKID_CPUCLK>;
> +			#cooling-cells = <2>; /* min followed by max */
>  		};
>  
>  		cpu2: cpu at 202 {
> @@ -50,6 +53,7 @@ cpu2: cpu at 202 {
>  			resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>;
>  			operating-points-v2 = <&cpu_opp_table>;
>  			clocks = <&clkc CLKID_CPUCLK>;
> +			#cooling-cells = <2>; /* min followed by max */
>  		};
>  
>  		cpu3: cpu at 203 {
> @@ -61,6 +65,7 @@ cpu3: cpu at 203 {
>  			resets = <&clkc CLKC_RESET_CPU3_SOFT_RESET>;
>  			operating-points-v2 = <&cpu_opp_table>;
>  			clocks = <&clkc CLKID_CPUCLK>;
> +			#cooling-cells = <2>; /* min followed by max */
>  		};
>  	};
>  
> @@ -190,6 +195,54 @@ power-firmware at 4f00000 {
>  		};
>  	};
>  
> +	thermal-zones {
> +		soc {
> +			polling-delay-passive = <250>; /* milliseconds */
> +			polling-delay = <1000>; /* milliseconds */
> +			thermal-sensors = <&thermal_sensor>;
> +
> +			cooling-maps {
> +				map0 {
> +					trip = <&soc_passive>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +
> +				map1 {
> +					trip = <&soc_hot>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +
> +			trips {
> +				soc_passive: soc-passive {
> +					temperature = <80000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "passive";
> +				};
> +
> +				soc_hot: soc-hot {
> +					temperature = <90000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "hot";
> +				};
> +
> +				soc_critical: soc-critical {
> +					temperature = <110000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "critical";
> +				};
> +			};
> +		};
> +	};
> +
>  	mmcbus: bus at c8000000 {
>  		compatible = "simple-bus";
>  		reg = <0xc8000000 0x8000>;
> @@ -254,6 +307,7 @@ mali: gpu at c0000 {
>  			clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
>  			clock-names = "bus", "core";
>  			operating-points-v2 = <&gpu_opp_table>;
> +			#cooling-cells = <2>; /* min followed by max */
>  		};
>  	};
>  }; /* end of / */
> 

Reviewed-by: Neil Armstrong <narmstrong at baylibre.com>