[PATCH 3/3] arm64: dts: rockchip: rk3328: Add Radxa ROCK Pi E
Chen-Yu Tsai
wens at kernel.org
Sun Jan 10 22:42:45 EST 2021
On Mon, Jan 11, 2021 at 4:17 AM Johan Jonker <jbx6244 at gmail.com> wrote:
>
> Hi Chen-Yu,
>
> Most is already answered by Heiko.
>
> On 1/10/21 4:37 PM, Chen-Yu Tsai wrote:
> > Hi,
> >
> > On Sun, Jan 10, 2021 at 10:45 PM Johan Jonker <jbx6244 at gmail.com> wrote:
> >>
> >> Hi Chen-Yu,
> >>
> >> Some comments, have a look if it is useful...
> >>
> >> On 1/10/21 4:58 AM, Chen-Yu Tsai wrote:
> >>> From: Chen-Yu Tsai <wens at csie.org>
> >>>
> >>> Radxa ROCK Pi E is a router oriented SBC based on Rockchip's RK3328 SoC.
> >>> As the official wiki page puts it, "E for Ethernets".
> >>>
> >>> It features the RK3328 SoC, gigabit and fast Ethernet RJ45 ports, both
> >>> directly served by Ethernet controllers in the SoC, a USB 3.0 host port,
> >>> a power-only USB type-C port, a 3.5mm headphone jack for audio output,
> >>
> >>> two LEDs, a 40-pin Raspberry Pi style GPIO header, and optional WiFi+BT
> >>> and PoE header.
> >>>
> >>> The board comes in multiple configurations, differing in the amount of
> >>> onboard RAM, the level of WiFi+BT (none, 802.11n 2.4GHz, or 802.11ac
> >>> 2.4 GHz & 5 GHz), and whether PoE is supported or not. These variants
> >>> can all share the same device tree.
> >>>
> >>> The USB 2.0 OTG controller is available on the 40-pin header. This is
> >>> not enabled in the device tree, since it is possible to use it in a
> >>> host-only configuration, or in OTG mode with an extra pin from the
> >>> header as the ID pin.
> >>>
> >>> The device tree is based on the one of the Rock64, with various parts
> >>> modified to match the ROCK Pi E, and some parts updated to newer styles,
> >>> such as the gmac2io node's mdio sub-node.
> >>>
> >>> Add a new device tree file for the new board.
> >>>
> >>> Signed-off-by: Chen-Yu Tsai <wens at csie.org>
> >>> ---
> >>> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> >>> .../boot/dts/rockchip/rk3328-rock-pi-e.dts | 369 ++++++++++++++++++
> >>> 2 files changed, 370 insertions(+)
> >>> create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> >>>
> >>> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> >>> index 622d320ddd13..62d3abc17a24 100644
> >>> --- a/arch/arm64/boot/dts/rockchip/Makefile
> >>> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> >>> @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> >>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> >>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
> >>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> >>> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb
> >>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
> >>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
> >>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
> >>> diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> >>> new file mode 100644
> >>> index 000000000000..7818d2e8180c
> >>> --- /dev/null
> >>> +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts
> >>> @@ -0,0 +1,369 @@
> >>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> >>> +/*
> >>> + * (C) Copyright 2020 Chen-Yu Tsai <wens at csie.org>
> >>> + *
> >>> + * Based on ./rk3328-rock64.dts, which is
> >>> + *
> >>> + * Copyright (c) 2017 PINE64
> >>> + */
> >>> +
> >>> +/dts-v1/;
> >>> +
> >>> +#include <dt-bindings/leds/common.h>
> >>> +#include <dt-bindings/gpio/gpio.h>
> >>> +#include <dt-bindings/pinctrl/rockchip.h>
> >>> +#include "rk3328.dtsi"
> >>> +
> >>> +/ {
> >>> + model = "Radxa ROCK Pi E";
> >>> + compatible = "radxa,rockpi-e", "rockchip,rk3328";
> >>> +
> >>> + chosen {
> >>> + stdout-path = "serial2:1500000n8";
> >>> + };
> >>> +
> >>> + gmac_clkin: external-gmac-clock {
> >>> + compatible = "fixed-clock";
> >>> + clock-frequency = <125000000>;
> >>> + clock-output-names = "gmac_clkin";
> >>> + #clock-cells = <0>;
> >>> + };
> >>> +
> >>> + leds {
> >>> + compatible = "gpio-leds";
> >>> + pinctrl-0 = <&led_pin>;
> >>> + pinctrl-names = "default";
> >>> +
> >>> + led-0 {
> >>
> >>> + /* schematic say green but the actual thing is blue */
> >>
> >> In rockpie-v1.2-20200427-sch.pdf this led is already called "LED_BLUE",
> >> so comment maybe not needed anymore?
> >
> > Thanks. Did not notice there was a new revision.
> >
> >>> + color = <LED_COLOR_ID_BLUE>;
> >>> + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
> >>> + linux,default-trigger = "heartbeat";
> >>> + };> + };
> >>> +
> >>> + vcc_sd: sdmmc-regulator {
> >>> + compatible = "regulator-fixed";
> >>> + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&sdmmc0m1_pin>;
> >>
> >>> + regulator-boot-on;
> >>> + regulator-name = "vcc_sd";
> >>
> >> regulator-name above other regulator properties
> >
> > That is actually what I was used to, but some other rockchip dts files
> > have all the properties sorted alphabetically. So I stuck with what I
> > saw.
> >
> >> regulator voltage missing
> >> make things as complete as possible
> >>
> >> from fixed-regulator.yaml:
> >>
> >> description:
> >> Any property defined as part of the core regulator binding, defined in
> >> regulator.yaml, can also be used. However a fixed voltage regulator is
> >> expected to have the regulator-min-microvolt and regulator-max-microvolt
> >> to be the same.
> >
> > However this is not a real regulator; it is merely an on/off switch.
> > I believe in this case it should just pass through the voltage from
> > its upstream.
>
> This board is not black box. The schematics are public, so finding out
> limits was not the problem. Up to you if added or not...
As far as Linux is concerned, if the regulator does not have constraints /
voltages, then its upstream one's values is passed through. I believe that
correctly represents what the hardware is doing, so I will stick to that.
I might have asked Mark about this in the past, but I don't remember
exactly when and where.
> >>> + vin-supply = <&vcc_io>;
> >>> + };
> >>> +
> >>
> >>> + vcc_host_5v: vcc-host-5v-regulator {
> >>> + compatible = "regulator-fixed";
> >>> + gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&usb30_host_drv>;
> >>> + enable-active-high;
> >>> + regulator-name = "vcc_host_5v";
> >>
> >> idem limits
> >
> > Same here.
> >
> >>> + regulator-always-on;
> >>> + regulator-boot-on;
> >>> + vin-supply = <&vcc_sys>;
> >>> + };
> >>
> >> For Heiko: ?? remove ??
> >> usb3 has no support in mainline.
> >> Regulators not in use are disabled.
> >> For mainline this node has no use....
> >
> > As it already has a defined binding, we can put it in the device tree.
> >
> >>> +
> >>> + vcc_sys: vcc-sys {
> >>> + compatible = "regulator-fixed";
> >>> + regulator-name = "vcc_sys";
> >>
> >>> + regulator-always-on;
> >>> + regulator-boot-on;
> >>
> >> At the other regulators this is sort below the regulator limits.
> >
> > Again, alphabetically sorted vs preferred sorting method.
>
> There's some room for "creativity", but you must use that "style"
> document wise. But not above limits in "vcc_sys" and below in "vcc_io".
Sorry. I thought you were referring to the other fixed regulators.
I see now you meant the regulators in the PMIC. I will fix those up
to have consistent styling.
Seems that other boards have the same problem.
> From Heiko:
>
> compatible
> reg
> interrupts
> [alphabetical]
> status [if needed]
>
> ////////////////////
>
> My list:
>
> For nodes:
> If exists on top: model, compatible and chosen.
> Sort things without reg alphabetical first,
> then sort the rest by reg address.
>
> Inside nodes:
> If exists on top: compatible, reg and interrupts.
> In alphabetical order the required properties.
> Then in alphabetical order the other properties.
> And as last things that start with '#' in alphabetical order.
For me, it makes more sense to keep #gpio-cells grouped together with
gpio-controller, and the same for other controller types. #clock-cells
grouped with clock-output-names also makes it easier to read.
#address-cells and #size-cells naturally go to the end of the list as
what they really affect are the child nodes, which get listed after.
Since Heiko is OK either way, I'll stick to my ordering for now.
> Add status below all other properties for soc internal components with
> any board-specifics.
> Keep an empty line between properties and nodes.
>
> Exceptions:
> Sort pinctrl-0 above pinctrl-names, so it stays in line with clock-names
> and dma-names.
> Sort simple-audio-card,name above other simple-audio-card properties.
> Sort regulator-name above other regulator properties.
> Sort regulator-min-microvolt above regulator-max-microvolt.
>
> >
> >>> + regulator-min-microvolt = <5000000>;
> >>> + regulator-max-microvolt = <5000000>;
> >>> + };
> >>> +
> >>> + vcc_wifi: vcc-wifi-regulator {
> >>> + compatible = "regulator-fixed";
> >>> + gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&wifi_en>;
> >>> + regulator-name = "vcc_wifi";
> >>
> >> idem limits
> >
> > Again, it is just a switch.
> >
> >>> + regulator-always-on;
> >>> + regulator-boot-on;
> >>> + vin-supply = <&vcc_io>;
> >>> + };
> >>> +};
> >>> +
> >>> +&analog_sound {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&codec {
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&cpu0 {
> >>> + cpu-supply = <&vdd_arm>;
> >>> +};
> >>> +
> >>> +&cpu1 {
> >>> + cpu-supply = <&vdd_arm>;
> >>> +};
> >>> +
> >>> +&cpu2 {
> >>> + cpu-supply = <&vdd_arm>;
> >>> +};
> >>> +
> >>> +&cpu3 {
> >>> + cpu-supply = <&vdd_arm>;
> >>> +};
> >>> +
> >>> +&emmc {
> >>> + bus-width = <8>;
> >>> + cap-mmc-highspeed;
> >>
> >>> + max-frequency = <150000000>;
> >>
> >> remove
> >> already defined in dtsi
> >
> > OK.
> >
> >>> + mmc-ddr-1_8v;
> >>> + mmc-hs200-1_8v;
> >>> + non-removable;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>;
> >>> + vmmc-supply = <&vcc_io>;
> >>> + vqmmc-supply = <&vcc18_emmc>;
> >>> + status = "okay";
> >>> +};
> >>
> >> ////////////////////////
> >> emmc: mmc at ff520000 {
> >> compatible = "rockchip,rk3328-dw-mshc", "rockchip,rk3288-dw-mshc";
> >> reg = <0x0 0xff520000 0x0 0x4000>;
> >> interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> >> clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
> >> <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
> >> clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
> >> fifo-depth = <0x100>;
> >> max-frequency = <150000000>;
> >> status = "disabled";
> >> };
> >> ////////////////////////
> >>
> >>> +
> >>> +&gmac2io {
> >>> + assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
> >>> + assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
> >>> + clock_in_out = "input";
> >>> + phy-handle = <&rtl8211e>;
> >>> + phy-mode = "rgmii";
> >>> + phy-supply = <&vcc_io>;
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&rgmiim1_pins>;
> >>> + snps,aal;
> >>> + snps,rxpbl = <0x4>;
> >>> + snps,txpbl = <0x4>;
> >>> + tx_delay = <0x26>;
> >>> + rx_delay = <0x11>;
> >>> + status = "okay";
> >>> +
> >>> + mdio {
> >>> + compatible = "snps,dwmac-mdio";
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> +
> >>> + rtl8211e: ethernet-phy at 1 {
> >>> + reg = <1>;
> >>> + pinctrl-0 = <ð_phy_int_pin>, <ð_phy_reset_pin>;
> >>> + pinctrl-names = "default";
> >>> + interrupt-parent = <&gpio1>;
> >>> + interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
> >>> + reset-assert-us = <10000>;
> >>> + reset-deassert-us = <50000>;
> >>> + reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
> >>> + };
> >>> + };
> >>> +};
> >>> +
> >>> +&gmac2phy {
> >>> + pinctrl-names = "default";
> >>> + pinctrl-0 = <&fephyled_linkm1>, <&fephyled_rxm1>;
> >>> + status = "okay";
> >>> +};
> >>> +
> >>> +&i2c1 {
> >>> + status = "okay";
> >>> +
> >>> + rk805: pmic at 18 {
> >>> + compatible = "rockchip,rk805";
> >>> + reg = <0x18>;
> >>> + interrupt-parent = <&gpio2>;
> >>> + interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
> >>
> >>> + #clock-cells = <1>;
> >>
> >> all thing that start with "#" down the list
> >
> > Is there a proper "preferred" sorting method defined somewhere?
>
> See above.
>
> >
> >>> + clock-output-names = "xin32k", "rk805-clkout2";
> >>> + gpio-controller;
> >>
> >>> + #gpio-cells = <2>;
> >>
> >> idem
> >>
snip
> >>> +
> >>> +&pinctrl {
> >>
> >>> + ethernet-phy {
> >>
> >> gmac2io
> >
> > OK.
I thought about this a bit more, and I think e-phy or ephy would be a
better name, since these pin functions are not directly related to
gmac2io, but the external Ethernet PHY.
It would be nicer if we could fix the ethernet-phy binding though.
> >> phy / ethernet-phy is a reserved node name
> >> use something else
> >>
> >> make ARCH=arm64 dtbs_check
> >>
> >> /arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dt.yaml: ethernet-phy:
> >> 'reg' is a required property
> >> From schema: Documentation/devicetree/bindings/net/ethernet-phy.yaml
> >
> > That's somewhat annoying. :(
> >
> > I wouldn't say the name is "reserved", just that the binding checking
> > mechanism can't account for these situations.
> >
> >>> + eth_phy_int_pin: eth-phy-int-pin {
> >>> + rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_down>;
> >>> + };
> >>> +
> >>> + eth_phy_reset_pin: eth-phy-reset-pin {
> >>> + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
> >>> + };
> >>> + };
> >>> +
snip
> >>> +&saradc {
> >>> + vref-supply = <&vcc_18>;
> >>> + status = "okay";
> >>> +};
> >>
> >> What happened to the recovery key from the schematic?
> >
> > I believe I originally planned on adding it, but failed to find a proper
> > key event for it. Any suggestions?
>
> The consensus seem to be "KEY_VENDOR".
>
> Example:
>
> adc-keys {
> compatible = "adc-keys";
> io-channels = <&saradc 0>;
> io-channel-names = "buttons";
> keyup-threshold-microvolt = <1800000>;
> poll-interval = <100>;
>
> recovery {
> label = "recovery";
> linux,code = <KEY_VENDOR>;
> press-threshold-microvolt = <17000>;
> };
> };
Thanks. Though I really wonder what Linux or other OSes could do with it.
ChenYu
More information about the linux-arm-kernel
mailing list