[PATCH v2 2/2] drm/sun4i: tcon: improve DCLK polarity handling

[Maxime Ripard]

Hi,

Thanks for those patches

On Thu, Jan 07, 2021 at 03:30:32AM +0100, Giulio Benetti wrote:
> From: Giulio Benetti <giulio.benetti at micronovasrl.com>
> 
> It turned out(Maxime suggestion) that bit 26 of SUN4I_TCON0_IO_POL_REG is
> dedicated to invert DCLK polarity and this makes thing really easier than
> before. So let's handle DCLK polarity by adding
> SUN4I_TCON0_IO_POL_DCLK_POSITIVE as bit 26 and activating according to
> bus_flags the same way is done for all the other signals.
> 
> Cc: Maxime Ripard <maxime at cerno.tech>

Suggested-by would be nice here :)

> Signed-off-by: Giulio Benetti <giulio.benetti at micronovasrl.com>
> ---
>  drivers/gpu/drm/sun4i/sun4i_tcon.c | 20 +-------------------
>  drivers/gpu/drm/sun4i/sun4i_tcon.h |  1 +
>  2 files changed, 2 insertions(+), 19 deletions(-)
> 
> diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
> index 52598bb0fb0b..30171ccd87e5 100644
> --- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
> +++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
> @@ -569,26 +569,8 @@ static void sun4i_tcon0_mode_set_rgb(struct sun4i_tcon *tcon,
>  	if (info->bus_flags & DRM_BUS_FLAG_DE_LOW)
>  		val |= SUN4I_TCON0_IO_POL_DE_NEGATIVE;
>  
> -	/*
> -	 * On A20 and similar SoCs, the only way to achieve Positive Edge
> -	 * (Rising Edge), is setting dclk clock phase to 2/3(240°).
> -	 * By default TCON works in Negative Edge(Falling Edge),
> -	 * this is why phase is set to 0 in that case.
> -	 * Unfortunately there's no way to logically invert dclk through
> -	 * IO_POL register.
> -	 * The only acceptable way to work, triple checked with scope,
> -	 * is using clock phase set to 0° for Negative Edge and set to 240°
> -	 * for Positive Edge.
> -	 * On A33 and similar SoCs there would be a 90° phase option,
> -	 * but it divides also dclk by 2.
> -	 * Following code is a way to avoid quirks all around TCON
> -	 * and DOTCLOCK drivers.
> -	 */
>  	if (info->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE)
> -		clk_set_phase(tcon->dclk, 0);
> -
> -	if (info->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
> -		clk_set_phase(tcon->dclk, 240);
> +		val |= SUN4I_TCON0_IO_POL_DCLK_POSITIVE;

I'm not really sure why we need the first patch of this series here?
That patch only seem to undo what you did in patch 1

Maxime