[PATCH] irqchip/irq-pruss-intc: implement set_type() callback

[David Lechner]

On 1/5/21 2:47 AM, Marc Zyngier wrote:
> On 2021-01-04 18:36, David Lechner wrote:
>> This implements the irqchip set_type() callback for the TI PRUSS
>> interrupt controller. This is needed for cases where an event needs
>> to be active low.
>>
>> According to the technical reference manual, the polarity should always
>> be set to high, however in practice, the polarity needs to be set low
>> for the McASP Tx/Rx system event in conjunction with soft UART PRU
>> firmware for TI AM18XX SoCs, otherwise it doesn't work.
> 
> I remember asking about this when I reviewed the patch series, and
> was told that there was no need to handle anything *but* level high.
> As a consequence, the DT binding doesn't have any way to express
> the trigger configuration.
> 
> Now this? What is going to drive the configuration?

I made it work by setting IRQF_TRIGGER_LOW in devm_request_irq().

I can try to see if there is a way to change the (10 year old)
firmware instead.

Hopefully someone from TI can shed more light on the subject?

> 
>>
>> Signed-off-by: David Lechner <david at lechnology.com>
>> ---
>>  drivers/irqchip/irq-pruss-intc.c | 27 +++++++++++++++++++++++++++
>>  1 file changed, 27 insertions(+)
>>
>> diff --git a/drivers/irqchip/irq-pruss-intc.c b/drivers/irqchip/irq-pruss-intc.c
>> index 5409016e6ca0..f882af8a7ded 100644
>> --- a/drivers/irqchip/irq-pruss-intc.c
>> +++ b/drivers/irqchip/irq-pruss-intc.c
>> @@ -334,6 +334,32 @@ static void pruss_intc_irq_unmask(struct irq_data *data)
>>      pruss_intc_write_reg(intc, PRU_INTC_EISR, hwirq);
>>  }
>>
>> +static int pruss_intc_irq_set_type(struct irq_data *data, unsigned int type)
>> +{
>> +    struct pruss_intc *intc = irq_data_get_irq_chip_data(data);
>> +    u32 reg, bit, val;
>> +
>> +    if (type & IRQ_TYPE_LEVEL_MASK) {
>> +        /* polarity register */
>> +        reg = PRU_INTC_SIPR(data->hwirq / 32);
>> +        bit = BIT(data->hwirq % 32);
>> +        val = pruss_intc_read_reg(intc, reg);
>> +
>> +        /*
>> +         * This check also ensures that IRQ_TYPE_DEFAULT will result
>> +         * in setting the level to high.
>> +         */
>> +        if (type & IRQ_TYPE_LEVEL_HIGH)
>> +            val |= bit;
>> +        else
>> +            val &= ~bit;
>> +
>> +        pruss_intc_write_reg(intc, reg, val);
> 
> RMW  of a shared register without locking?
> 
>> +    }
>> +
>> +    return 0;
> 
> What happens when this is passed an edge configuration? It should at
> least return an error.

This is probably a moot point if we are not going to allow
changing the type, but there is another register for selecting
edge or level. But the manual says similarly says it should
always be set to level.

> 
>> +}
>> +
>>  static int pruss_intc_irq_reqres(struct irq_data *data)
>>  {
>>      if (!try_module_get(THIS_MODULE))
>> @@ -389,6 +415,7 @@ static struct irq_chip pruss_irqchip = {
>>      .irq_ack        = pruss_intc_irq_ack,
>>      .irq_mask        = pruss_intc_irq_mask,
>>      .irq_unmask        = pruss_intc_irq_unmask,
>> +    .irq_set_type        = pruss_intc_irq_set_type,
>>      .irq_request_resources    = pruss_intc_irq_reqres,
>>      .irq_release_resources    = pruss_intc_irq_relres,
>>      .irq_get_irqchip_state    = pruss_intc_irq_get_irqchip_state,
> 
> Thanks,
> 
>          M.