[PATCH v8 01/11] firmware: arm_scmi: Add configurable polling mode for transports

[Cristian Marussi]

SCMI communications along TX channels can optionally be provided of a
completion interrupt; when such interrupt is not available, command
transactions should rely on polling, where the SCMI core takes care to
repeatedly evaluate the transport-specific .poll_done() function, if
available, to determine if and when a request was fully completed or
timed out.

Such mechanism is already present and working on a single transfer base:
SCMI protocols can indeed enable hdr.poll_completion on specific commands
ahead of each transfer and cause that transaction to be handled with
polling.

Introduce a couple of flags to be able to enforce such polling behaviour
globally at will:

 - scmi_desc.force_polling: to statically switch the whole transport to
   polling mode.

 - scmi_chan_info.no_completion_irq: to switch a single channel dynamically
   to polling mode if, at runtime, is determined that no completion
   interrupt was available for such channel.

Signed-off-by: Cristian Marussi <cristian.marussi at arm.com>
---
v7 --> v8
- removed internal poling_enabled flag, using macros
v5 --> v6
- removed check on replies received by IRQs when xfer was requested
  as poll_completion (not all transport can suppress IRQs on an xfer basis)
v4 --> v5
- make force_polling const
- introduce polling_enabled flag to simplify checks on do_xfer
v3 --> v4:
- renamed .needs_polling flag to .no_completion_irq
- refactored error path when polling needed but not supported
---
 drivers/firmware/arm_scmi/common.h |  8 ++++++++
 drivers/firmware/arm_scmi/driver.c | 32 ++++++++++++++++++++++++++++++
 2 files changed, 40 insertions(+)

diff --git a/drivers/firmware/arm_scmi/common.h b/drivers/firmware/arm_scmi/common.h
index 6438b5248c24..652e5d95ee65 100644
--- a/drivers/firmware/arm_scmi/common.h
+++ b/drivers/firmware/arm_scmi/common.h
@@ -339,11 +339,16 @@ void scmi_protocol_release(const struct scmi_handle *handle, u8 protocol_id);
  * @dev: Reference to device in the SCMI hierarchy corresponding to this
  *	 channel
  * @handle: Pointer to SCMI entity handle
+ * @no_completion_irq: Flag to indicate that this channel has no completion
+ *		       interrupt mechanism for synchronous commands.
+ *		       This can be dynamically set by transports at run-time
+ *		       inside their provided .chan_setup().
  * @transport_info: Transport layer related information
  */
 struct scmi_chan_info {
 	struct device *dev;
 	struct scmi_handle *handle;
+	bool no_completion_irq;
 	void *transport_info;
 };
 
@@ -402,6 +407,8 @@ struct scmi_device *scmi_child_dev_find(struct device *parent,
  *	be pending simultaneously in the system. May be overridden by the
  *	get_max_msg op.
  * @max_msg_size: Maximum size of data per message that can be handled.
+ * @force_polling: Flag to force this whole transport to use SCMI core polling
+ *		   mechanism instead of completion interrupts even if available.
  */
 struct scmi_desc {
 	int (*transport_init)(void);
@@ -410,6 +417,7 @@ struct scmi_desc {
 	int max_rx_timeout_ms;
 	int max_msg;
 	int max_msg_size;
+	const bool force_polling;
 };
 
 #ifdef CONFIG_ARM_SCMI_TRANSPORT_MAILBOX
diff --git a/drivers/firmware/arm_scmi/driver.c b/drivers/firmware/arm_scmi/driver.c
index 476b91845e40..cb9fc12503f2 100644
--- a/drivers/firmware/arm_scmi/driver.c
+++ b/drivers/firmware/arm_scmi/driver.c
@@ -36,6 +36,23 @@
 #define CREATE_TRACE_POINTS
 #include <trace/events/scmi.h>
 
+#define IS_POLLING_REQUIRED(__c, __i)					\
+	((__c)->no_completion_irq || (__i)->desc->force_polling)	\
+
+#define IS_TRANSPORT_POLLING_CAPABLE(__i)				\
+	((__i)->desc->ops->poll_done)
+
+#define IS_POLLING_ENABLED(__c, __i)					\
+({									\
+	bool __ret;							\
+	typeof(__c) c_ = __c;						\
+	typeof(__i) i_ = __i;						\
+									\
+	__ret = (IS_POLLING_REQUIRED(c_, i_) &&				\
+			IS_TRANSPORT_POLLING_CAPABLE(i_));		\
+	__ret;								\
+})
+
 enum scmi_error_codes {
 	SCMI_SUCCESS = 0,	/* Success */
 	SCMI_ERR_SUPPORT = -1,	/* Not supported */
@@ -817,6 +834,7 @@ static int do_xfer(const struct scmi_protocol_handle *ph,
 	struct device *dev = info->dev;
 	struct scmi_chan_info *cinfo;
 
+	/* Check for polling request on custom command xfers at first */
 	if (xfer->hdr.poll_completion && !info->desc->ops->poll_done) {
 		dev_warn_once(dev,
 			      "Polling mode is not supported by transport.\n");
@@ -827,6 +845,10 @@ static int do_xfer(const struct scmi_protocol_handle *ph,
 	if (unlikely(!cinfo))
 		return -EINVAL;
 
+	/* True ONLY if also supported by transport. */
+	if (IS_POLLING_ENABLED(cinfo, info))
+		xfer->hdr.poll_completion = true;
+
 	/*
 	 * Initialise protocol id now from protocol handle to avoid it being
 	 * overridden by mistake (or malice) by the protocol code mangling with
@@ -1527,6 +1549,16 @@ static int scmi_chan_setup(struct scmi_info *info, struct device *dev,
 	if (ret)
 		return ret;
 
+	if (tx && IS_POLLING_REQUIRED(cinfo, info)) {
+		if (IS_TRANSPORT_POLLING_CAPABLE(info))
+			dev_info(dev,
+				 "Enabled polling mode TX channel - prot_id:%d\n",
+				 prot_id);
+		else
+			dev_warn(dev,
+				 "Polling mode NOT supported by transport.\n");
+	}
+
 idr_alloc:
 	ret = idr_alloc(idr, cinfo, prot_id, prot_id + 1, GFP_KERNEL);
 	if (ret != prot_id) {
-- 
2.17.1