[RESEND PATCH v2] PCI: mediatek: Delay 100ms to wait power and clock to become stable

[Bjorn Helgaas]

[+cc Marc, Alyssa, Mark, Luca for reset timing questions]

On Tue, Dec 07, 2021 at 04:41:53PM +0800, qizhong cheng wrote:
> Described in PCIe CEM specification sections 2.2 (PERST# Signal) and
> 2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should
> be delayed 100ms (TPVPERL) for the power and clock to become stable.
> 
> Signed-off-by: qizhong cheng <qizhong.cheng at mediatek.com>
> Acked-by: Pali Rohár <pali at kernel.org>
> ---
> 
> v2:
>  - Typo fix.
>  - Rewrap into one paragraph.

1) If you change something, even in the commit log or comments, it is
a new version, not a "RESEND".  A "RESEND" means "I sent this quite a
while ago and didn't hear anything, so I'm sending the exact same
thing again in case the first one got lost."

2) I suggested a subject line update, which apparently got missed.
Here's a better one:

  PCI: mediatek: Assert PERST# for 100ms for power and clock to stabilize

3) Most importantly, this needs to be reconciled with the similar
change to the apple driver:

  https://lore.kernel.org/r/20211123180636.80558-2-maz@kernel.org

In the apple driver, we're doing:

  - Assert PERST#
  - Set up REFCLK
  - Sleep 100us (T_perst-clk, CEM r5 2.2, 2.9.2)
  - Deassert PERST#
  - Sleep 100ms (not sure there's a name? PCIe r5 6.6.1)

But here in mediatek, we're doing:

  - Assert PERST#
  - Sleep 100ms (T_pvperl, CEM r5 2.2, 2.2.1, 2.9.2)
  - Deassert PERST#

My questions:

  - Where does apple enforce T_pvperl?  I can't tell where power to
    the slot is turned on.

  - Where does mediatek enforce the PCIe sec 6.6.1 delay after
    deasserting PERST# and before config requests?

  - Does either apple or mediatek support speeds greater than 5 GT/s,
    and if so, shouldn't we start the sec 6.6.1 100ms delay *after*
    Link training completes?

>  drivers/pci/controller/pcie-mediatek.c | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/drivers/pci/controller/pcie-mediatek.c b/drivers/pci/controller/pcie-mediatek.c
> index 2f3f974977a3..a61ea3940471 100644
> --- a/drivers/pci/controller/pcie-mediatek.c
> +++ b/drivers/pci/controller/pcie-mediatek.c
> @@ -702,6 +702,13 @@ static int mtk_pcie_startup_port_v2(struct mtk_pcie_port *port)
>  	 */
>  	writel(PCIE_LINKDOWN_RST_EN, port->base + PCIE_RST_CTRL);
>  
> +	/*
> +	 * Described in PCIe CEM specification sections 2.2 (PERST# Signal) and
> +	 * 2.2.1 (Initial Power-Up (G3 to S0)). The deassertion of PERST# should
> +	 * be delayed 100ms (TPVPERL) for the power and clock to become stable.
> +	 */
> +	msleep(100);
> +
>  	/* De-assert PHY, PE, PIPE, MAC and configuration reset	*/
>  	val = readl(port->base + PCIE_RST_CTRL);
>  	val |= PCIE_PHY_RSTB | PCIE_PERSTB | PCIE_PIPE_SRSTB |
> -- 
> 2.25.1
>