[PATCH v4 7/7] arm64: dts: exynos: Add initial device tree support for Exynos7885 SoC
Krzysztof Kozlowski
krzysztof.kozlowski at canonical.com
Tue Dec 7 01:39:13 PST 2021
On 06/12/2021 16:31, David Virag wrote:
> Add initial Exynos7885 device tree nodes with dts for the Samsung Galaxy
> A8 (2018), a.k.a. "jackpotlte", with model number "SM-A530F".
> Currently this includes some clock support, UART support, and I2C nodes.
>
> Signed-off-by: David Virag <virag.david003 at gmail.com>
> ---
> Changes in v2:
> - Remove address-cells, and size-cells from dts, since they are
> already in the dtsi.
> - Lower case hex in memory node
> - Fix node names with underscore instead of hyphen
> - Fix line breaks
> - Fix "-key" missing from gpio keys node names
> - Use the form without "key" in gpio key labels on all keys
> - Suffix pin configuration node names with "-pins"
> - Remove "fimc_is_mclk" nodes from pinctrl dtsi for now
> - Use macros for "samsung,pin-con-pdn", and "samsung,pin-con-pdn"
> - Add comment about Arm PMU
> - Rename "clock-oscclk" to "osc-clock"
> - Include exynos-syscon-restart.dtsi instead of rewriting its contents
>
> Changes in v3:
> - Fix typo (seperate -> separate)
>
> Changes in v4:
> - Fixed leading 0x in clock-controller nodes
> - Actually suffixed pin configuration node names with "-pins"
> - Seperated Cortex-A53 and Cortex-A73 PMU
>
> arch/arm64/boot/dts/exynos/Makefile | 7 +-
> .../boot/dts/exynos/exynos7885-jackpotlte.dts | 95 ++
> .../boot/dts/exynos/exynos7885-pinctrl.dtsi | 865 ++++++++++++++++++
> arch/arm64/boot/dts/exynos/exynos7885.dtsi | 438 +++++++++
> 4 files changed, 1402 insertions(+), 3 deletions(-)
> create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
> create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
> create mode 100644 arch/arm64/boot/dts/exynos/exynos7885.dtsi
>
(...)
> +
> + gpp8: gpp8 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + /* DECON TE */
> + decon_f_te_on: decon_f_te_on-pins {
> + samsung,pins = "gpc0-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
> + };
> +
> + decon_f_te_off: decon_f_te_off-pins {
Drop these, similarly to FIMC. Only one pin configuration will be used
when you add DECON support, not two. If you wish to keep one, the proper
for DECON operating state, this also needs fixing of underscores->hyphens.
> + samsung,pins = "gpc0-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> + };
> +
(...)
> diff --git a/arch/arm64/boot/dts/exynos/exynos7885.dtsi b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
> new file mode 100644
> index 000000000000..cc7a5ce0c103
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
> @@ -0,0 +1,438 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung Exynos7885 SoC device tree source
> + *
> + * Copyright (c) 2021 Samsung Electronics Co., Ltd.
> + * Copyright (c) 2021 Dávid Virág
> + *
> + */
> +
> +#include <dt-bindings/clock/exynos7885.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> + compatible = "samsung,exynos7885";
> + #address-cells = <2>;
> + #size-cells = <1>;
> +
> + interrupt-parent = <&gic>;
> +
> + aliases {
> + pinctrl0 = &pinctrl_alive;
> + pinctrl1 = &pinctrl_dispaud;
> + pinctrl2 = &pinctrl_fsys;
> + pinctrl3 = &pinctrl_top;
> + };
> +
> + arm-a53-pmu {
> + compatible = "arm,cortex-a53-pmu";
> + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&cpu0>,
> + <&cpu1>,
> + <&cpu2>,
> + <&cpu3>,
> + <&cpu4>,
> + <&cpu5>;
> + };
> +
> + arm-a73-pmu {
> + compatible = "arm,cortex-a73-pmu";
> + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&cpu6>,
> + <&cpu7>;
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&cpu0>;
> + };
> + core1 {
> + cpu = <&cpu1>;
> + };
> + core2 {
> + cpu = <&cpu2>;
> + };
> + core3 {
> + cpu = <&cpu3>;
> + };
> + core4 {
> + cpu = <&cpu4>;
> + };
> + core5 {
> + cpu = <&cpu5>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&cpu6>;
> + };
> + core1 {
> + cpu = <&cpu7>;
> + };
> + };
> + };
> +
> + cpu0: cpu at 100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x100>;
> + enable-method = "psci";
> + };
> +
> + cpu1: cpu at 101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x101>;
> + enable-method = "psci";
> + };
> +
> + cpu2: cpu at 102 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x102>;
> + enable-method = "psci";
> + };
> +
> + cpu3: cpu at 103 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x103>;
> + enable-method = "psci";
> + };
> +
> + cpu4: cpu at 200 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x200>;
> + enable-method = "psci";
> + };
> +
> + cpu5: cpu at 201 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53";
> + reg = <0x201>;
> + enable-method = "psci";
> + };
> +
> + cpu6: cpu at 0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a73";
> + reg = <0x0>;
> + enable-method = "psci";
> + };
> +
> + cpu7: cpu at 1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a73";
> + reg = <0x1>;
> + enable-method = "psci";
> + };
> + };
> +
> + psci {
> + compatible = "arm,psci";
> + method = "smc";
> + cpu_suspend = <0xc4000001>;
> + cpu_off = <0x84000002>;
> + cpu_on = <0xc4000003>;
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + /* Hypervisor Virtual Timer interrupt is not wired to GIC */
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + fixed-rate-clocks {
> + oscclk: osc-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "oscclk";
> + };
> + };
> +
> + soc: soc at 0 {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x0 0x0 0x0 0x20000000>;
> +
> + chipid at 10000000 {
> + compatible = "samsung,exynos850-chipid";
> + reg = <0x10000000 0x24>;
> + };
> +
> + gic: interrupt-controller at 12301000 {
> + compatible = "arm,gic-400";
> + #interrupt-cells = <3>;
> + #address-cells = <0>;
> + interrupt-controller;
> + reg = <0x12301000 0x1000>,
> + <0x12302000 0x2000>,
> + <0x12304000 0x2000>,
> + <0x12306000 0x2000>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
> + IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + cmu_peri: clock-controller at 10010000 {
> + compatible = "samsung,exynos7885-cmu-peri";
> + reg = <0x10010000 0x8000>;
> + #clock-cells = <1>;
> +
> + clocks = <&oscclk>,
> + <&cmu_top CLK_DOUT_PERI_BUS>,
> + <&cmu_top CLK_DOUT_PERI_SPI0>,
> + <&cmu_top CLK_DOUT_PERI_SPI1>,
> + <&cmu_top CLK_DOUT_PERI_UART0>,
> + <&cmu_top CLK_DOUT_PERI_UART1>,
> + <&cmu_top CLK_DOUT_PERI_UART2>,
> + <&cmu_top CLK_DOUT_PERI_USI0>,
> + <&cmu_top CLK_DOUT_PERI_USI1>,
> + <&cmu_top CLK_DOUT_PERI_USI2>;
> + clock-names = "oscclk",
> + "dout_peri_bus",
> + "dout_peri_spi0",
> + "dout_peri_spi1",
> + "dout_peri_uart0",
> + "dout_peri_uart1",
> + "dout_peri_uart2",
> + "dout_peri_usi0",
> + "dout_peri_usi1",
> + "dout_peri_usi2";
> + };
> +
> + cmu_core: clock-controller at 12000000 {
> + compatible = "samsung,exynos7885-cmu-core";
> + reg = <0x12000000 0x8000>;
> + #clock-cells = <1>;
> +
> + clocks = <&oscclk>,
> + <&cmu_top CLK_DOUT_CORE_BUS>,
> + <&cmu_top CLK_DOUT_CORE_CCI>,
> + <&cmu_top CLK_DOUT_CORE_G3D>;
> + clock-names = "oscclk", "dout_core_bus", "dout_core_cci", "dout_core_g3d";
> + };
> +
> + cmu_top: clock-controller at 12060000 {
> + compatible = "samsung,exynos7885-cmu-top";
> + reg = <0x12060000 0x8000>;
> + #clock-cells = <1>;
> +
> + clocks = <&oscclk>;
> + clock-names = "oscclk";
> + };
> +
> + pinctrl_alive: pinctrl at 11cb0000 {
> + compatible = "samsung,exynos7885-pinctrl";
> + reg = <0x11cb0000 0x1000>;
> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> +
> + wakeup-interrupt-controller {
> + compatible = "samsung,exynos7-wakeup-eint";
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
> + };
> + };
> +
> + pinctrl_dispaud: pinctrl at 148f0000 {
Let's bring some order - put pinctrl nodes within each other ordered by
unit address. The ordering of other nodes is okay, we never actually
enforced any logic here.
> + compatible = "samsung,exynos7885-pinctrl";
> + reg = <0x148f0000 0x1000>;
> + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + pinctrl_fsys: pinctrl at 13430000 {
> + compatible = "samsung,exynos7885-pinctrl";
> + reg = <0x13430000 0x1000>;
> + interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + pinctrl_top: pinctrl at 139b0000 {
> + compatible = "samsung,exynos7885-pinctrl";
> + reg = <0x139b0000 0x1000>;
> + interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list