[PATCH v15 3/3] ARM: dts: imx7d: remarkable2: add wacom digitizer device

[Benjamin Tissoires]

On Thu, Dec 2, 2021 at 12:56 PM Alistair Francis <alistair at alistair23.me> wrote:
>
> Signed-off-by: Alistair Francis <alistair at alistair23.me>
> ---
>  arch/arm/boot/dts/imx7d-remarkable2.dts | 59 +++++++++++++++++++++++++

I think I am always asking the same question, but is it fine for me to
take this patch through the hid tree?
I seem to remember that this was a little bit free for all but I'd
like to get the confirmation first.

Cheers,
Benjamin


>  1 file changed, 59 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx7d-remarkable2.dts b/arch/arm/boot/dts/imx7d-remarkable2.dts
> index 89cbf13097a4..a2a91bfdd98e 100644
> --- a/arch/arm/boot/dts/imx7d-remarkable2.dts
> +++ b/arch/arm/boot/dts/imx7d-remarkable2.dts
> @@ -34,6 +34,19 @@ reg_brcm: regulator-brcm {
>                 startup-delay-us = <150>;
>         };
>
> +       reg_digitizer: regulator-digitizer {
> +               compatible = "regulator-fixed";
> +               regulator-name = "VDD_3V3_DIGITIZER";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               pinctrl-names = "default", "sleep";
> +               pinctrl-0 = <&pinctrl_digitizer_reg>;
> +               pinctrl-1 = <&pinctrl_digitizer_reg>;
> +               gpio = <&gpio1 6 GPIO_ACTIVE_HIGH>;
> +               enable-active-high;
> +               startup-delay-us = <100000>; /* 100 ms */
> +       };
> +
>         wifi_pwrseq: wifi_pwrseq {
>                 compatible = "mmc-pwrseq-simple";
>                 pinctrl-names = "default";
> @@ -51,6 +64,26 @@ &clks {
>         assigned-clock-rates = <0>, <32768>;
>  };
>
> +&i2c1 {
> +       clock-frequency = <400000>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pinctrl_i2c1>;
> +       status = "okay";
> +
> +       wacom_digitizer: digitizer at 9 {
> +               compatible = "hid-over-i2c";
> +               reg = <0x09>;
> +               hid-descr-addr = <0x01>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pinctrl_wacom>;
> +               interrupt-parent = <&gpio1>;
> +               interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
> +               touchscreen-inverted-x;
> +               touchscreen-inverted-y;
> +               vdd-supply = <&reg_digitizer>;
> +       };
> +};
> +
>  &snvs_pwrkey {
>         status = "okay";
>  };
> @@ -117,6 +150,25 @@ &wdog1 {
>         fsl,ext-reset-output;
>  };
>
> +&iomuxc_lpsr {
> +       pinctrl_digitizer_reg: digitizerreggrp {
> +               fsl,pins = <
> +                       /* DIGITIZER_PWR_EN */
> +                       MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6     0x14
> +               >;
> +       };
> +
> +       pinctrl_wacom: wacomgrp {
> +               fsl,pins = <
> +                       /*MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5   0x00000014 FWE */
> +                       MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4     0x00000074 /* PDCTB */
> +                       MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1     0x00000034 /* WACOM INT */
> +                       /*MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6   0x00000014 WACOM PWR ENABLE */
> +                       /*MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0   0x00000074 WACOM RESET */
> +               >;
> +       };
> +};
> +
>  &iomuxc {
>         pinctrl_brcm_reg: brcmreggrp {
>                 fsl,pins = <
> @@ -125,6 +177,13 @@ MX7D_PAD_SAI1_TX_BCLK__GPIO6_IO13  0x14
>                 >;
>         };
>
> +       pinctrl_i2c1: i2c1grp {
> +               fsl,pins = <
> +                       MX7D_PAD_I2C1_SDA__I2C1_SDA             0x4000007f
> +                       MX7D_PAD_I2C1_SCL__I2C1_SCL             0x4000007f
> +               >;
> +       };
> +
>         pinctrl_uart1: uart1grp {
>                 fsl,pins = <
>                         MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX    0x79
> --
> 2.31.1
>