[PATCH v2 4/5] arm64: dts: ti: Add initial support for J721S2 System on Module
Aswath Govindraju
a-govindraju at ti.com
Fri Dec 3 04:21:09 PST 2021
A System on Module (SoM) contains the SoC, PMIC, DDR and basic high speed
components necessary for functionality. Therefore, add support for the
components present on the SoM.
SoM: https://www.ti.com/lit/zip/sprr439
Signed-off-by: Aswath Govindraju <a-govindraju at ti.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 175 +++++++++++++++++++
1 file changed, 175 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
new file mode 100644
index 000000000000..76f0ceacb6d4
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SoM: https://www.ti.com/lit/zip/sprr439
+ *
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-j721s2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ memory at 80000000 {
+ device_type = "memory";
+ /* 16 GB RAM */
+ reg = <0x00 0x80000000 0x00 0x80000000>,
+ <0x08 0x80000000 0x03 0x80000000>;
+ };
+
+ /* Reserving memory regions still pending */
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secure_ddr: optee at 9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>;
+ alignment = <0x1000>;
+ no-map;
+ };
+ };
+
+ transceiver0: can-phy0 {
+ /* standby pin has been grounded by default */
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ };
+};
+
+&main_pmx0 {
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AH25) I2C0_SCL */
+ J721S2_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AE24) I2C0_SDA */
+ >;
+ };
+
+ main_mcan16_pins_default: main-mcan16-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x028, PIN_INPUT, 0) /* (AB24) MCAN16_RX */
+ J721S2_IOPAD(0x024, PIN_OUTPUT, 0) /* (Y28) MCAN16_TX */
+ >;
+ };
+};
+
+&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
+ exp_som: gpio at 21 {
+ compatible = "ti,tca6408";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0",
+ "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1",
+ "GPIO_RGMII1_RST", "GPIO_eDP_ENABLE",
+ "GPIO_LIN_EN", "CAN_STB";
+ };
+};
+
+&main_mcan16 {
+ pinctrl-0 = <&main_mcan16_pins_default>;
+ pinctrl-names = "default";
+ phys = <&transceiver0>;
+};
+
+&mailbox0_cluster0 {
+ status = "disabled";
+};
+
+&mailbox0_cluster1 {
+ status = "disabled";
+};
+
+&mailbox0_cluster2 {
+ status = "disabled";
+};
+
+&mailbox0_cluster3 {
+ status = "disabled";
+};
+
+&mailbox0_cluster4 {
+ status = "disabled";
+};
+
+&mailbox0_cluster5 {
+ status = "disabled";
+};
+
+&mailbox0_cluster6 {
+ status = "disabled";
+};
+
+&mailbox0_cluster7 {
+ status = "disabled";
+};
+
+&mailbox0_cluster8 {
+ status = "disabled";
+};
+
+&mailbox0_cluster9 {
+ status = "disabled";
+};
+
+&mailbox0_cluster10 {
+ status = "disabled";
+};
+
+&mailbox0_cluster11 {
+ status = "disabled";
+};
+
+&mailbox1_cluster0 {
+ status = "disabled";
+};
+
+&mailbox1_cluster1 {
+ status = "disabled";
+};
+
+&mailbox1_cluster2 {
+ status = "disabled";
+};
+
+&mailbox1_cluster3 {
+ status = "disabled";
+};
+
+&mailbox1_cluster4 {
+ status = "disabled";
+};
+
+&mailbox1_cluster5 {
+ status = "disabled";
+};
+
+&mailbox1_cluster6 {
+ status = "disabled";
+};
+
+&mailbox1_cluster7 {
+ status = "disabled";
+};
+
+&mailbox1_cluster8 {
+ status = "disabled";
+};
+
+&mailbox1_cluster9 {
+ status = "disabled";
+};
+
+&mailbox1_cluster10 {
+ status = "disabled";
+};
+
+&mailbox1_cluster11 {
+ status = "disabled";
+};
--
2.17.1
More information about the linux-arm-kernel
mailing list