[PATCH devicetree 2/2] arm64: dts: add device tree for the LX2160A on the NXP BlueBox3 board
Vladimir Oltean
vladimir.oltean at nxp.com
Fri Aug 27 13:27:22 PDT 2021
From: Wasim Khan <wasim.khan at nxp.com>
The NXP BlueBox3 is a prototyping board for high-performance autonomous
driving systems. It contains two Linux systems, on running on the
LX2160A and the other on the S32G2 SoC. This patch adds the device tree
support for the LX2160A SoC.
In terms of networking from the LX2160A's perspective, there are:
- 4 RJ45 10G ports using Aquantia copper PHYs which are attached
directly to DPAA2 ports on the LX2160A
- 3 NXP SJA1110 automotive Ethernet switches. First two are managed by
the LX2160A (each switch has a host port towards a dpmac), the third
switch is managed by the S32G2. All 3 switches are interconnected
through on-board SERDES lanes. The cascade ports between the 2
switches managed by LX2160A form a DSA link, the cascade ports between
the LX2160A and the S32G2 domain form user ports (the "to_sw3" net
device).
- 2 RJ45 1G ports using Atheros copper PHYs which are attached directly
to NXP SJA1110 switches
- 12 automotive 100base-T1 single-pair Ethernet ports routed from the
SJA1110 internal PHY ports (TJA1103)
- One SGMII SERDES lane towards an internal connector, attached to one
of the SJA1110 switch ports
On board rev A, the AR8035 RGMII PHY addresses were different than on
rev B and later. This patch introduces a separate device tree for rev A.
The main device tree is supposed to cover rev B and later.
Signed-off-by: Wasim Khan <wasim.khan at nxp.com>
Co-developed-by: Vabhav Sharma <vabhav.sharma at nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma at nxp.com>
Co-developed-by: Kuldeep Singh <kuldeep.singh at nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh at nxp.com>
Co-developed-by: Florin Chiculita <florinlaurentiu.chiculita at nxp.com>
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita at nxp.com>
Co-developed-by: Biwen Li <biwen.li at nxp.com>
Signed-off-by: Biwen Li <biwen.li at nxp.com>
Co-developed-by: Heinz Wrobel <Heinz.Wrobel at nxp.com>
Signed-off-by: Heinz Wrobel <Heinz.Wrobel at nxp.com>
Co-developed-by: Yangbo Lu <yangbo.lu at nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu at nxp.com>
Co-developed-by: Vladimir Oltean <vladimir.oltean at nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean at nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 2 +
.../freescale/fsl-lx2160a-bluebox3-rev-a.dts | 34 +
.../dts/freescale/fsl-lx2160a-bluebox3.dts | 658 ++++++++++++++++++
3 files changed, 694 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index db9e36ebe932..ecf74464705f 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
new file mode 100644
index 000000000000..15d273c93154
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160A BLUEBOX3
+//
+// Copyright 2020-2021 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a-bluebox3.dts"
+
+/ {
+ compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a";
+};
+
+/* The RGMII PHYs have a different MDIO address */
+&emdio1 {
+ /delete-node/ ethernet-phy at 5;
+
+ sw1_mii3_phy: ethernet-phy at 1 {
+ /* AR8035 */
+ compatible = "ethernet-phy-id004d.d072";
+ reg = <0x1>;
+ interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ /delete-node/ ethernet-phy at 6;
+
+ sw2_mii3_phy: ethernet-phy at 2 {
+ /* AR8035 */
+ compatible = "ethernet-phy-id004d.d072";
+ reg = <0x2>;
+ interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
new file mode 100644
index 000000000000..be7d01630a6f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
@@ -0,0 +1,658 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160A BLUEBOX3
+//
+// Copyright 2020-2021 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+ model = "NXP Layerscape LX2160ABLUEBOX3";
+ compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a";
+
+ aliases {
+ crypto = &crypto;
+ serial0 = &uart0;
+ mmc0 = &esdhc0;
+ mmc1 = &esdhc1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ sb_3v3: regulator-sb3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "MC34717-3.3VSB";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&can0 {
+ status = "okay";
+
+ can-transceiver {
+ max-bitrate = <5000000>;
+ };
+};
+
+&can1 {
+ status = "okay";
+
+ can-transceiver {
+ max-bitrate = <5000000>;
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+&dpmac5 {
+ phy-handle = <&aqr113c_phy1>;
+ phy-mode = "usxgmii";
+ managed = "in-band-status";
+};
+
+&dpmac6 {
+ phy-handle = <&aqr113c_phy2>;
+ phy-mode = "usxgmii";
+ managed = "in-band-status";
+};
+
+&dpmac9 {
+ phy-handle = <&aqr113c_phy3>;
+ phy-mode = "usxgmii";
+ managed = "in-band-status";
+};
+
+&dpmac10 {
+ phy-handle = <&aqr113c_phy4>;
+ phy-mode = "usxgmii";
+ managed = "in-band-status";
+};
+
+&dpmac17 {
+ phy-mode = "rgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&dpmac18 {
+ phy-mode = "rgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&emdio1 {
+ status = "okay";
+
+ aqr113c_phy2: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x0>;
+ /* IRQ_10G_PHY2 */
+ interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ aqr113c_phy1: ethernet-phy at 8 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x8>;
+ /* IRQ_10G_PHY1 */
+ interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ sw1_mii3_phy: ethernet-phy at 5 {
+ /* AR8035 */
+ compatible = "ethernet-phy-id004d.d072";
+ reg = <0x5>;
+ interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ sw2_mii3_phy: ethernet-phy at 6 {
+ /* AR8035 */
+ compatible = "ethernet-phy-id004d.d072";
+ reg = <0x6>;
+ interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&emdio2 {
+ status = "okay";
+
+ aqr113c_phy4: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x0>;
+ /* IRQ_10G_PHY4 */
+ interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ aqr113c_phy3: ethernet-phy at 8 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x8>;
+ /* IRQ_10G_PHY3 */
+ interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&esdhc0 {
+ sd-uhs-sdr104;
+ sd-uhs-sdr50;
+ sd-uhs-sdr25;
+ sd-uhs-sdr12;
+ status = "okay";
+};
+
+&esdhc1 {
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&fspi {
+ status = "okay";
+
+ mt35xu512aba0: flash at 0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ m25p,fast-read;
+ spi-max-frequency = <50000000>;
+ spi-rx-bus-width = <8>;
+ spi-tx-bus-width = <8>;
+ };
+
+ mt35xu512aba1: flash at 1 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <1>;
+ m25p,fast-read;
+ spi-max-frequency = <50000000>;
+ spi-rx-bus-width = <8>;
+ spi-tx-bus-width = <8>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ i2c-mux at 77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ power-monitor at 40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <500>;
+ };
+ };
+
+ i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ temp2: temperature-sensor at 48 {
+ compatible = "nxp,sa56004";
+ reg = <0x48>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ temp1: temperature-sensor at 4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+
+ i2c at 4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4>;
+
+ rtc at 51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+
+ i2c at 7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x7>;
+
+ i2c-mux at 75 {
+ compatible = "nxp,pca9547";
+ reg = <0x75>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0>;
+
+ spi_bridge: spi at 28 {
+ compatible = "nxp,sc18is602b";
+ reg = <0x28>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+
+ i2c-mux at 77 {
+ compatible = "nxp,pca9846";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x1>;
+
+ /* The I2C multiplexer and temperature sensors are on
+ * the T6 riser card.
+ */
+ i2c-mux at 70 {
+ compatible = "nxp,pca9548";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6>;
+
+ q12: temperature-sensor at 4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+
+ i2c at 7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x7>;
+
+ q11: temperature-sensor at 4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ q13: temperature-sensor at 48 {
+ compatible = "nxp,sa56004";
+ reg = <0x48>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ q14: temperature-sensor at 4a {
+ compatible = "nxp,sa56004";
+ reg = <0x4a>;
+ vcc-supply = <&sb_3v3>;
+ #thermal-sensor-cells = <1>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&pcs_mdio5 {
+ status = "okay";
+};
+
+&pcs_mdio6 {
+ status = "okay";
+};
+
+&pcs_mdio9 {
+ status = "okay";
+};
+
+&pcs_mdio10 {
+ status = "okay";
+};
+
+&spi_bridge {
+ sw1: ethernet-switch at 0 {
+ compatible = "nxp,sja1110a";
+ reg = <0>;
+ spi-max-frequency = <4000000>;
+ spi-cpol;
+ dsa,member = <0 0>;
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microcontroller port */
+ port at 0 {
+ reg = <0>;
+ status = "disabled";
+ };
+
+ /* SW1_P1 */
+ port at 1 {
+ reg = <1>;
+ label = "con_2x20";
+ phy-mode = "sgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+ ethernet = <&dpmac17>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "1ge_p1";
+ phy-mode = "rgmii-id";
+ phy-handle = <&sw1_mii3_phy>;
+ };
+
+ sw1p4: port at 4 {
+ reg = <4>;
+ link = <&sw2p1>;
+ phy-mode = "sgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port at 5 {
+ reg = <5>;
+ label = "trx1";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port5_base_t1_phy>;
+ };
+
+ port at 6 {
+ reg = <6>;
+ label = "trx2";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port6_base_t1_phy>;
+ };
+
+ port at 7 {
+ reg = <7>;
+ label = "trx3";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port7_base_t1_phy>;
+ };
+
+ port at 8 {
+ reg = <8>;
+ label = "trx4";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port8_base_t1_phy>;
+ };
+
+ port at 9 {
+ reg = <9>;
+ label = "trx5";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port9_base_t1_phy>;
+ };
+
+ port at a {
+ reg = <10>;
+ label = "trx6";
+ phy-mode = "internal";
+ phy-handle = <&sw1_port10_base_t1_phy>;
+ };
+ };
+
+ mdios {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio at 0 {
+ compatible = "nxp,sja1110-base-t1-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ sw1_port5_base_t1_phy: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x1>;
+ };
+
+ sw1_port6_base_t1_phy: ethernet-phy at 2 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x2>;
+ };
+
+ sw1_port7_base_t1_phy: ethernet-phy at 3 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x3>;
+ };
+
+ sw1_port8_base_t1_phy: ethernet-phy at 4 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x4>;
+ };
+
+ sw1_port9_base_t1_phy: ethernet-phy at 5 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x5>;
+ };
+
+ sw1_port10_base_t1_phy: ethernet-phy at 6 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x6>;
+ };
+ };
+ };
+ };
+
+ sw2: ethernet-switch at 2 {
+ compatible = "nxp,sja1110a";
+ reg = <2>;
+ spi-max-frequency = <4000000>;
+ spi-cpol;
+ dsa,member = <0 1>;
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microcontroller port */
+ port at 0 {
+ reg = <0>;
+ status = "disabled";
+ };
+
+ sw2p1: port at 1 {
+ reg = <1>;
+ link = <&sw1p4>;
+ phy-mode = "sgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+ ethernet = <&dpmac18>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "1ge_p2";
+ phy-mode = "rgmii-id";
+ phy-handle = <&sw2_mii3_phy>;
+ };
+
+ port at 4 {
+ reg = <4>;
+ label = "to_sw3";
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ };
+ };
+
+ port at 5 {
+ reg = <5>;
+ label = "trx7";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port5_base_t1_phy>;
+ };
+
+ port at 6 {
+ reg = <6>;
+ label = "trx8";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port6_base_t1_phy>;
+ };
+
+ port at 7 {
+ reg = <7>;
+ label = "trx9";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port7_base_t1_phy>;
+ };
+
+ port at 8 {
+ reg = <8>;
+ label = "trx10";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port8_base_t1_phy>;
+ };
+
+ port at 9 {
+ reg = <9>;
+ label = "trx11";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port9_base_t1_phy>;
+ };
+
+ port at a {
+ reg = <10>;
+ label = "trx12";
+ phy-mode = "internal";
+ phy-handle = <&sw2_port10_base_t1_phy>;
+ };
+ };
+
+ mdios {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio at 0 {
+ compatible = "nxp,sja1110-base-t1-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ sw2_port5_base_t1_phy: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x1>;
+ };
+
+ sw2_port6_base_t1_phy: ethernet-phy at 2 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x2>;
+ };
+
+ sw2_port7_base_t1_phy: ethernet-phy at 3 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x3>;
+ };
+
+ sw2_port8_base_t1_phy: ethernet-phy at 4 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x4>;
+ };
+
+ sw2_port9_base_t1_phy: ethernet-phy at 5 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x5>;
+ };
+
+ sw2_port10_base_t1_phy: ethernet-phy at 6 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0x6>;
+ };
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
--
2.25.1
More information about the linux-arm-kernel
mailing list