[PATCH v7 08/10] arm64: dts: HiSilicon: Add support for HiKey 970 PCIe controller hardware

[Rob Herring]

On Wed, Jul 21, 2021 at 3:39 AM Mauro Carvalho Chehab
<mchehab+huawei at kernel.org> wrote:
>
> From: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
>
> Add DTS bindings for the HiKey 970 board's PCIe hardware.
>
> Co-developed-by: Mauro Carvalho Chehab <mchehab+huawei at kernel.org>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei at kernel.org>
> ---
>  arch/arm64/boot/dts/hisilicon/hi3670.dtsi     | 71 +++++++++++++++++++
>  .../boot/dts/hisilicon/hikey970-pmic.dtsi     |  1 -
>  drivers/pci/controller/dwc/pcie-kirin.c       | 12 ----
>  3 files changed, 71 insertions(+), 13 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
> index 1f228612192c..6dfcfcfeedae 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
> +++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
> @@ -177,6 +177,12 @@ sctrl: sctrl at fff0a000 {
>                         #clock-cells = <1>;
>                 };
>
> +               pmctrl: pmctrl at fff31000 {
> +                       compatible = "hisilicon,hi3670-pmctrl", "syscon";
> +                       reg = <0x0 0xfff31000 0x0 0x1000>;
> +                       #clock-cells = <1>;
> +               };
> +
>                 iomcu: iomcu at ffd7e000 {
>                         compatible = "hisilicon,hi3670-iomcu", "syscon";
>                         reg = <0x0 0xffd7e000 0x0 0x1000>;
> @@ -660,6 +666,71 @@ gpio28: gpio at fff1d000 {
>                         clock-names = "apb_pclk";
>                 };
>
> +               its_pcie: interrupt-controller at f4000000 {
> +                       compatible = "arm,gic-v3-its";
> +                       msi-controller;
> +                       reg = <0x0 0xf5100000 0x0 0x100000>;

How does this h/w have a GIC-400 (which is GICv2) and then a GIC v3 ITS?

> +               };
> +
> +               pcie_phy: pcie-phy at fc000000 {
> +                       compatible = "hisilicon,hi970-pcie-phy";
> +                       reg = <0x0 0xfc000000 0x0 0x80000>;
> +
> +                       phy-supply = <&ldo33>;
> +
> +                       clocks = <&crg_ctrl HI3670_CLK_GATE_PCIEPHY_REF>,
> +                                <&crg_ctrl HI3670_CLK_GATE_PCIEAUX>,
> +                                <&crg_ctrl HI3670_PCLK_GATE_PCIE_PHY>,
> +                                <&crg_ctrl HI3670_PCLK_GATE_PCIE_SYS>,
> +                                <&crg_ctrl HI3670_ACLK_GATE_PCIE>;
> +                       clock-names = "phy_ref", "aux",
> +                                     "apb_phy", "apb_sys",
> +                                     "aclk";
> +
> +                       reset-gpios = <&gpio7 0 0 >, <&gpio25 2 0 >,
> +                                     <&gpio3 1 0 >, <&gpio27 4 0 >;
> +
> +                       clkreq-gpios = <&gpio20 6 0 >, <&gpio27 3 0 >,
> +                                      <&gpio17 0 0 >;
> +
> +                       /* vboost iboost pre post main */
> +                       hisilicon,eye-diagram-param = <0xFFFFFFFF 0xFFFFFFFF
> +                                                      0xFFFFFFFF 0xFFFFFFFF
> +                                                      0xFFFFFFFF>;
> +
> +                       #phy-cells = <0>;
> +               };
> +
> +               pcie at f4000000 {
> +                       compatible = "hisilicon,kirin970-pcie";
> +                       reg = <0x0 0xf4000000 0x0 0x1000000>,
> +                             <0x0 0xfc180000 0x0 0x1000>,
> +                             <0x0 0xf5000000 0x0 0x2000>;
> +                       reg-names = "dbi", "apb", "config";
> +                       bus-range = <0x0  0x1>;
> +                       msi-parent = <&its_pcie>;

This means the PCI host doesn't have a MSI controller...

> +                       #address-cells = <3>;
> +                       #size-cells = <2>;
> +                       device_type = "pci";
> +                       phys = <&pcie_phy>;
> +                       ranges = <0x02000000 0x0 0x00000000
> +                                 0x0 0xf6000000
> +                                 0x0 0x02000000>;
> +                       num-lanes = <1>;
> +                       #interrupt-cells = <1>;
> +                       interrupts = <0 283 4>;
> +                       interrupt-names = "msi";

But then this says it does...