[PATCH v10 3/5] spmi: mediatek: Add support for MT6873/8192
Hsin-hsiung Wang
hsin-hsiung.wang at mediatek.com
Mon Aug 16 05:11:38 PDT 2021
Hi,
On Mon, 2021-08-09 at 10:55 -0700, Stephen Boyd wrote:
> Quoting Hsin-Hsiung Wang (2021-08-02 23:34:19)
> > diff --git a/drivers/spmi/spmi-mtk-pmif.c b/drivers/spmi/spmi-mtk-pmif.c
> > new file mode 100644
> > index 000000000000..94c45d46ab0c
> > --- /dev/null
> > +++ b/drivers/spmi/spmi-mtk-pmif.c
> > @@ -0,0 +1,465 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +//
> > +// Copyright (c) 2021 MediaTek Inc.
> > +
> > +#include <linux/clk.h>
> > +#include <linux/iopoll.h>
> > +#include <linux/module.h>
> > +#include <linux/of_device.h>
>
> include platform_device.h for the platform device driver that this is.
>
Thanks for the commit, I will update it in the next patch.
> > +#include <linux/spmi.h>
> > +
> > +#define SWINF_IDLE 0x00
> > +#define SWINF_WFVLDCLR 0x06
> > +
> > +#define GET_SWINF(x) (((x) >> 1) & 0x7)
> > +
> > +#define PMIF_CMD_REG_0 0
> > +#define PMIF_CMD_REG 1
> > +#define PMIF_CMD_EXT_REG 2
> > +#define PMIF_CMD_EXT_REG_LONG 3
> > +
> > +#define PMIF_DELAY_US 10
> > +#define PMIF_TIMEOUT_US (10 * 1000)
> > +
> > +#define PMIF_CHAN_OFFSET 0x5
> > +
> > +#define PMIF_MAX_CLKS 3
> > +
> > +#define SPMI_OP_ST_BUSY 1
> > +
> > +struct ch_reg {
> > + u32 ch_sta;
> > + u32 wdata;
> > + u32 rdata;
> > + u32 ch_send;
> > + u32 ch_rdy;
> > +};
> > +
> > +struct pmif_data {
> > + const u32 *regs;
> > + const u32 *spmimst_regs;
> > + u32 soc_chan;
> > +};
> > +
> > +struct pmif {
> > + void __iomem *base;
> > + void __iomem *spmimst_base;
> > + struct ch_reg chan;
> > + struct clk_bulk_data clks[PMIF_MAX_CLKS];
> > + u32 nclks;
>
> size_t? Surely 32-bits isn't important.
>
Thanks. I will use size_t in the next patch.
> > + const struct pmif_data *data;
> > +};
> > +
> > +static const char * const pmif_clock_names[] = {
> > + "pmif_sys_ck", "pmif_tmr_ck", "spmimst_clk_mux",
> > +};
> [...]
> > +
> > +static bool pmif_is_fsm_vldclr(struct pmif *arb)
> > +{
> > + u32 reg_rdata;
> > +
> > + reg_rdata = pmif_readl(arb, arb->chan.ch_sta);
>
> Newline here please.
>
Thanks, I will update it in the next patch.
> > + return GET_SWINF(reg_rdata) == SWINF_WFVLDCLR;
> > +}
> > +
> > +static int pmif_arb_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid)
> > +{
> > + struct pmif *arb = spmi_controller_get_drvdata(ctrl);
> > + u32 rdata, cmd;
> > + int ret;
> > +
> > + /* Check the opcode */
> > + if (opc < SPMI_CMD_RESET || opc > SPMI_CMD_WAKEUP)
> > + return -EINVAL;
> > +
> > + cmd = opc - SPMI_CMD_RESET;
> > +
> > + mtk_spmi_writel(arb, (cmd << 0x4) | sid, SPMI_OP_ST_CTRL);
> > + ret = readl_poll_timeout_atomic(arb->spmimst_base + arb->data->spmimst_regs[SPMI_OP_ST_STA],
> > + rdata, (rdata & SPMI_OP_ST_BUSY) == SPMI_OP_ST_BUSY,
> > + PMIF_DELAY_US, PMIF_TIMEOUT_US);
> > + if (ret < 0)
> > + dev_err(&ctrl->dev, "timeout, err = %d\n", ret);
> > +
> > + return ret;
> > +}
> > +
> > +static int pmif_spmi_read_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid,
> > + u16 addr, u8 *buf, size_t len)
> > +{
> > + struct pmif *arb = spmi_controller_get_drvdata(ctrl);
> > + struct ch_reg *inf_reg;
> > + int ret;
> > + u32 data, cmd;
> > +
> > + /* Check for argument validation. */
> > + if (sid & ~0xf) {
> > + dev_err(&ctrl->dev, "exceed the max slv id\n");
> > + return -EINVAL;
> > + }
> > +
> > + if (len > 4) {
> > + dev_err(&ctrl->dev, "pmif supports 1..4 bytes per trans, but:%zu requested", len);
>
> Missing newline
>
Thanks, I will update it in the next patch.
> > + return -EINVAL;
> > + }
> > +
> > + if (opc >= 0x60 && opc <= 0x7f)
> > + opc = PMIF_CMD_REG;
> > + else if ((opc >= 0x20 && opc <= 0x2f) || (opc >= 0x38 && opc <= 0x3f))
> > + opc = PMIF_CMD_EXT_REG_LONG;
> > + else
> > + return -EINVAL;
> > +
> > + /* Wait for Software Interface FSM state to be IDLE. */
> > + inf_reg = &arb->chan;
> > + ret = readl_poll_timeout_atomic(arb->base + arb->data->regs[inf_reg->ch_sta],
> > + data, GET_SWINF(data) == SWINF_IDLE,
> > + PMIF_DELAY_US, PMIF_TIMEOUT_US);
> > + if (ret < 0) {
> > + /* set channel ready if the data has transferred */
> > + if (pmif_is_fsm_vldclr(arb))
> > + pmif_writel(arb, 1, inf_reg->ch_rdy);
> > + dev_err(&ctrl->dev, "failed to wait for SWINF_IDLE\n");
> > + goto out;
> > + }
> > +
> > + /* Send the command. */
> > + cmd = (opc << 30) | (sid << 24) | ((len - 1) << 16) | addr;
> > + pmif_writel(arb, cmd, inf_reg->ch_send);
> > +
> > + /*
> > + * Wait for Software Interface FSM state to be WFVLDCLR,
> > + * read the data and clear the valid flag.
> > + */
> > + ret = readl_poll_timeout_atomic(arb->base + arb->data->regs[inf_reg->ch_sta],
> > + data, GET_SWINF(data) == SWINF_WFVLDCLR,
> > + PMIF_DELAY_US, PMIF_TIMEOUT_US);
> > + if (ret < 0) {
> > + dev_err(&ctrl->dev, "failed to wait for SWINF_WFVLDCLR\n");
> > + goto out;
> > + }
> > +
> > + data = pmif_readl(arb, inf_reg->rdata);
> > + memcpy(buf, &data, len);
> > + pmif_writel(arb, 1, inf_reg->ch_rdy);
> > +
> > +out:
> > + if (ret < 0)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int pmif_spmi_write_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid,
> > + u16 addr, const u8 *buf, size_t len)
> > +{
> > + struct pmif *arb = spmi_controller_get_drvdata(ctrl);
> > + struct ch_reg *inf_reg;
> > + int ret;
> > + u32 data, cmd;
> > +
> > + if (len > 4) {
> > + dev_err(&ctrl->dev, "pmif supports 1..4 bytes per trans, but:%zu requested", len);
>
> Missing newline
>
Thanks, I will update it in the next patch.
> > + return -EINVAL;
> > + }
> > +
> > + /* Check the opcode */
> > + if (opc >= 0x40 && opc <= 0x5F)
> > + opc = PMIF_CMD_REG;
> > + else if ((opc <= 0xF) || (opc >= 0x30 && opc <= 0x37))
> > + opc = PMIF_CMD_EXT_REG_LONG;
> > + else if (opc >= 0x80)
> > + opc = PMIF_CMD_REG_0;
> > + else
> > + return -EINVAL;
> > +
> > + /* Wait for Software Interface FSM state to be IDLE. */
> > + inf_reg = &arb->chan;
> > + ret = readl_poll_timeout_atomic(arb->base + arb->data->regs[inf_reg->ch_sta],
> > + data, GET_SWINF(data) == SWINF_IDLE,
> > + PMIF_DELAY_US, PMIF_TIMEOUT_US);
> > + if (ret < 0) {
> > + /* set channel ready if the data has transferred */
> > + if (pmif_is_fsm_vldclr(arb))
> > + pmif_writel(arb, 1, inf_reg->ch_rdy);
> > + dev_err(&ctrl->dev, "failed to wait for SWINF_IDLE\n");
> > + goto out;
> > + }
> > +
> > + /* Set the write data. */
> > + memcpy(&data, buf, len);
> > + pmif_writel(arb, data, inf_reg->wdata);
> > +
> > + /* Send the command. */
> > + cmd = (opc << 30) | BIT(29) | (sid << 24) | ((len - 1) << 16) | addr;
> > + pmif_writel(arb, cmd, inf_reg->ch_send);
> > +
> > +out:
> > + if (ret < 0)
> > + return ret;
> > +
> > + return 0;
>
> Simplify to
>
> out:
> return ret;
>
Thanks, I will update it in the next patch.
> > +}
> > +
> > +static const struct pmif_data mt6873_pmif_arb = {
> > + .regs = mt6873_regs,
> > + .spmimst_regs = mt6873_spmi_regs,
> > + .soc_chan = 2,
> > +};
> > +
> > +static int mtk_spmi_probe(struct platform_device *pdev)
> > +{
> > + struct pmif *arb;
> > + struct spmi_controller *ctrl;
> > + int err, i;
> > + u32 chan_offset;
> > +
> > + ctrl = spmi_controller_alloc(&pdev->dev, sizeof(*arb));
> > + if (!ctrl)
> > + return -ENOMEM;
> > +
> > + arb = spmi_controller_get_drvdata(ctrl);
> > + arb->data = of_device_get_match_data(&pdev->dev);
>
> Use device_get_match_data() instead please.
>
Thanks, I will change to use device_get_match_data in the next patch.
> > + if (!arb->data) {
> > + err = -EINVAL;
> > + dev_err(&pdev->dev, "Cannot get drv_data\n");
> > + goto err_put_ctrl;
> > + }
> > +
> > + arb->base = devm_platform_ioremap_resource_byname(pdev, "pmif");
> > + if (IS_ERR(arb->base)) {
> > + err = PTR_ERR(arb->base);
> > + dev_err(&pdev->dev, "pmif failed to get the remappped memory\n");
>
> Please drop print as the API already prints errors for every problem.
>
Thanks, I will update it in the next patch.
> > + goto err_put_ctrl;
> > + }
> > +
> > + arb->spmimst_base = devm_platform_ioremap_resource_byname(pdev, "spmimst");
> > + if (IS_ERR(arb->spmimst_base)) {
> > + err = PTR_ERR(arb->spmimst_base);
> > + dev_err(&pdev->dev, "spmimst failed to get the remappped memory\n");
>
> Please drop print as the API already prints errors for every problem.
>
Thanks, I will update it in the next patch.
> > + goto err_put_ctrl;
> > + }
> > +
> > + arb->nclks = ARRAY_SIZE(pmif_clock_names);
> > + if (arb->nclks > PMIF_MAX_CLKS) {
> > + err = -EINVAL;
> > + dev_err(&pdev->dev, "exceed the max clock numbers\n");
>
> Do we really care? The dt schema should be checking this instead of the
> driver.
>
Thanks, I will remove the check in the next patch.
> > + goto err_put_ctrl;
> > + }
> > +
> > + for (i = 0; i < arb->nclks; i++)
> > + arb->clks[i].id = pmif_clock_names[i];
> > +
More information about the linux-arm-kernel
mailing list