[PATCH 5/8] arm64: dts: s32g2: add serial/uart support

[Andreas Färber]

Hi Chester et al.,

On 05.08.21 08:54, Chester Lin wrote:
> Add serial/uart support for NXP S32G2.

You might mention here that (following our initial stub) this commit is
now apparently based on the CodeAurora BSP branch foo (and therefore
adding its last-year copyright below and separate from 4/8).

> 

@NXP: If there are downstream Signed-off-bys that you would like to see
included for this portion here, please speak up.

> Signed-off-by: Chester Lin <clin at suse.com>
> ---
>  arch/arm64/boot/dts/freescale/s32g2.dtsi | 31 ++++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/s32g2.dtsi b/arch/arm64/boot/dts/freescale/s32g2.dtsi
> index 3321819c1a2d..0076eacad8a6 100644
> --- a/arch/arm64/boot/dts/freescale/s32g2.dtsi
> +++ b/arch/arm64/boot/dts/freescale/s32g2.dtsi
> @@ -1,6 +1,7 @@
>  // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
>  /*
>   * Copyright (c) 2021 SUSE LLC
> + * Copyright 2017-2020 NXP

@NXP: Should this be updated to include 2021 from your latest BSP
releases? Do you want it visually aligned by adding the ASCII-art?

>   */
>  
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> @@ -11,6 +12,12 @@ / {
>  	#address-cells = <2>;
>  	#size-cells = <2>;
>  
> +	aliases {
> +		serial0 = &uart0;
> +		serial1 = &uart1;
> +		serial2 = &uart2;
> +	};

Note: In the past there had been controversies as to whether to define
aliases globally for a SoC or in a .dts specific to a board's usage.
In this case it does not seem to matter much, as uart0 is being used as
console on the reference boards.

> +
>  	cpus {
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> @@ -82,6 +89,30 @@ soc {
>  
>  		ranges;
>  
> +		uart0: serial at 401c8000 {
> +			compatible = "fsl,s32g2-linflexuart",
> +				     "fsl,s32v234-linflexuart";
> +			reg = <0 0x401c8000 0 0x3000>;
> +			interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>;
> +			status = "disabled";
> +		};
> +
> +		uart1: serial at 401cc000 {
> +			compatible = "fsl,s32g2-linflexuart",
> +				     "fsl,s32v234-linflexuart";
> +			reg = <0 0x401cc000 0 0x3000>;
> +			interrupts = <GIC_SPI 83 IRQ_TYPE_EDGE_RISING>;
> +			status = "disabled";
> +		};
> +
> +		uart2: serial at 402bc000 {
> +			compatible = "fsl,s32g2-linflexuart",
> +				     "fsl,s32v234-linflexuart";
> +			reg = <0 0x402bc000 0 0x3000>;
> +			interrupts = <GIC_SPI 84 IRQ_TYPE_EDGE_RISING>;
> +			status = "disabled";
> +		};
> +
>  		gic: interrupt-controller at 50800000 {
>  			compatible = "arm,gic-v3";
>  			#interrupt-cells = <3>;

Regards,
Andreas

-- 
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer
HRB 36809 (AG Nürnberg)