[PATCH v3 7/7] arm64: dts: exynos: Add Exynos850 SoC support
Krzysztof Kozlowski
krzysztof.kozlowski at canonical.com
Thu Aug 12 01:17:32 PDT 2021
On 11/08/2021 13:48, Sam Protsenko wrote:
> Samsung Exynos850 is ARMv8-based mobile-oriented SoC.
>
> This patch adds minimal SoC support by including next Device Tree nodes:
>
> 1. Octa cores (Cortex-A55), supporting PSCI v1.0
> 2. ARM architecture timer (armv8-timer)
> 3. Interrupt controller (GIC-400)
> 4. Pinctrl nodes for GPIO
> 5. Serial node
>
> Signed-off-by: Sam Protsenko <semen.protsenko at linaro.org>
> ---
> Changes in v3:
> - Used generic fixed clock for serial
>
> Changes in v2:
> * Commit message:
> - Documented added dts features instead of CPU features
>
> * exynos850-usi.dtsi:
> - Removed, moved everything to exynos850.dtsi
>
> * exynos850.dtsi:
> - Root node:
> - Added comment about engineering name (Exynos3830)
> - Renamed pinctrl nodes, adding domain names
> - Used hard coded IRQ numbers instead of named constants everywhere
> - Added soc node, moved next nodes there: gic, clock, pinctrls and
> serial
> - Used address-cells=1 for soc node and removed unneeded 0x0 from
> reg properties
> - Moved exynos850-pinctrl.dtsi include line to the end of
> exynos850.dtsi
> - Coding style fixes
> - cpus:
> - Used address-cells=1 for cpus node
> - Renamed cpu at 0001 to cpu at 1, and so on
> - Left only "arm,cortex-a55" for cpus compatible
> - Renamed reg = <0x0001> to <0x1> for cpus
> - armv8 timer:
> - Add comment about missing HV timer IRQ to armv8 timer node
> - Removed not existing properties from armv8 timer node
> - Fixed cpu number in CPU_MASK()
> - Removed obsolete clock-frequency property
> - GIC:
> - Fixed GIC type to be GIC-400
> - Fixed size of GIC's 2nd region to be 0x2000
> - serial node:
> - Hard coded clock number for serial_0 for now; will replace with
> named const once proper clock driver is implemented
> - Removed gate_uart_clk0 clock from serial_0, as that clock is not
> supported in serial driver anyway (yet)
> - clock node:
> - Fixed clock controller node name (@0x12.. -> @12..)
>
> * exynos850-pinctrl.dtsi:
> - Referenced pinctrl nodes instead of defining those again in root node
> - Fixed interrupt-cells (3 -> 2)
> - Fixed USI related comments for pin config nodes
> - Removed decon_f_te_* and fm_lna_en nodes (won't be used)
> - Reordered pin config nodes by pin numbers
> - Improved all comments
> - Used existing named constants for pin-function and pin-pud
> - Fixed node names (used hyphens instead of underscore)
> - Fixed warnings found in W=1 build
>
> .../boot/dts/exynos/exynos850-pinctrl.dtsi | 748 ++++++++++++++++++
> arch/arm64/boot/dts/exynos/exynos850.dtsi | 261 ++++++
> 2 files changed, 1009 insertions(+)
> create mode 100644 arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> create mode 100644 arch/arm64/boot/dts/exynos/exynos850.dtsi
>
> diff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> new file mode 100644
> index 000000000000..ba5d5f33e2f6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> @@ -0,0 +1,748 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos850 SoC pin-mux and pin-config device tree source
> + *
> + * Copyright (C) 2017 Samsung Electronics Co., Ltd.
> + * Copyright (C) 2021 Linaro Ltd.
> + *
> + * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device
> + * tree nodes in this file.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/pinctrl/samsung.h>
> +
> +&pinctrl_alive {
> + gpa0: gpa0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpa1: gpa1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpa2: gpa2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpa3: gpa3 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpa4: gpa4 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpq0: gpq0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + /* I2C5 (also called CAM_PMIC_I2C in TRM) */
> + i2c5_bus: i2c5-bus {
> + samsung,pins = "gpa3-5", "gpa3-6";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* I2C6 (also called MOTOR_I2C in TRM) */
> + i2c6_bus: i2c6-bus {
> + samsung,pins = "gpa3-7", "gpa4-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* USI: UART */
> + uart0_bus: uart0-bus {
> + samsung,pins = "gpq0-0", "gpq0-1";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + };
> +};
> +
> +&pinctrl_cmgp {
> + gpm0: gpm0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm1: gpm1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm2: gpm2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm3: gpm3 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm4: gpm4 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpm5: gpm5 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupt-parent = <&gic>;
> + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + /* USI_CMGP0: HSI2C function */
> + hsi2c3_bus: hsi2c3-bus {
> + samsung,pins = "gpm0-0", "gpm1-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
There are also macros for DRV.
I assume you checked whether the actual values of FUNC/PULL/DRV macros
match Exynos850 datasheet.
> + };
> +
> + /* USI_CMGP0: UART function (4 pins, Auto Flow Control) */
> + uart1_bus_single: uart1-bus {
> + samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + };
> +
> + /* USI_CMGP0: UART function (2 pins, Non-Auto Flow Control) */
> + uart1_bus_dual: uart1-bus-dual {
> + samsung,pins = "gpm0-0", "gpm1-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + };
> +
> + /* USI_CMGP0: SPI function */
> + spi1_bus: spi1-bus {
> + samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi1_cs: spi1-cs {
> + samsung,pins = "gpm3-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi1_cs_func: spi1-cs-func {
> + samsung,pins = "gpm3-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* USI_CMGP1: HSI2C function */
> + hsi2c4_bus: hsi2c4-bus {
> + samsung,pins = "gpm4-0", "gpm5-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* USI_CMGP1: UART function (4 pins, Auto Flow Control) */
> + uart2_bus_single: uart2-bus {
> + samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + };
> +
> + /* USI_CMGP1: UART function (2 pins, Non-Auto Flow Control) */
> + uart2_bus_dual: uart2-bus-dual {
> + samsung,pins = "gpm4-0", "gpm5-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + };
> +
> + /* USI_CMGP1: SPI function */
> + spi2_bus: spi2-bus {
> + samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi2_cs: spi2-cs {
> + samsung,pins = "gpm7-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi2_cs_func: spi2-cs-func {
> + samsung,pins = "gpm7-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +};
> +
> +&pinctrl_aud {
> + gpb0: gpb0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpb1: gpb1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + aud_codec_mclk: aud-codec-mclk {
> + samsung,pins = "gpb0-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + };
> +
> + aud_codec_mclk_idle: aud-codec-mclk-idle {
> + samsung,pins = "gpb0-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + };
> +
> + aud_i2s0_bus: aud-i2s0-bus {
> + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + };
> +
> + aud_i2s0_idle: aud-i2s0-idle {
> + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + };
> +
> + aud_i2s1_bus: aud-i2s1-bus {
> + samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + };
> +
> + aud_i2s1_idle: aud-i2s1-idle {
> + samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + };
> +
> + aud_fm_bus: aud-fm-bus {
> + samsung,pins = "gpb1-4";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + };
> +
> + aud_fm_idle: aud-fm-idle {
> + samsung,pins = "gpb1-4";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + };
> +};
> +
> +&pinctrl_hsi {
> + gpf2: gpf2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + sd2_clk: sd2-clk {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_clk_fast_slew_rate_1x: sd2-clk-fast-slew-rate-1x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + sd2_clk_fast_slew_rate_1_5x: sd2-clk-fast-slew-rate-1-5x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <1>;
> + };
> +
> + sd2_clk_fast_slew_rate_2x: sd2-clk-fast-slew-rate-2x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_clk_fast_slew_rate_2_5x: sd2-clk-fast-slew-rate-2-5x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd2_clk_fast_slew_rate_3x: sd2-clk-fast-slew-rate-3x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <4>;
> + };
> +
> + sd2_clk_fast_slew_rate_4x: sd2-clk-fast-slew-rate-4x {
> + samsung,pins = "gpf2-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <5>;
> + };
> +
> + sd2_cmd: sd2-cmd {
> + samsung,pins = "gpf2-1";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_bus1: sd2-bus-width1 {
> + samsung,pins = "gpf2-2";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_bus4: sd2-bus-width4 {
> + samsung,pins = "gpf2-3", "gpf2-4", "gpf2-5";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd2_pins_as_pdn: sd2-pins-as-pdn {
> + samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
> + "gpf2-4", "gpf2-5";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + };
> +};
> +
> +&pinctrl_core {
> + gpf0: gpf0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpf1: gpf1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + sd0_clk: sd0-clk {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_clk_fast_slew_rate_1x: sd0-clk-fast-slew-rate-1x {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <1>;
> + };
> +
> + sd0_clk_fast_slew_rate_2x: sd0-clk-fast-slew-rate-2x {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd0_clk_fast_slew_rate_3x: sd0-clk-fast-slew-rate-3x {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <2>;
> + };
> +
> + sd0_clk_fast_slew_rate_4x: sd0-clk-fast-slew-rate-4x {
> + samsung,pins = "gpf0-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_cmd: sd0-cmd {
> + samsung,pins = "gpf0-1";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_rdqs: sd0-rdqs {
> + samsung,pins = "gpf0-2";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_nreset: sd0-nreset {
> + samsung,pins = "gpf0-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_bus1: sd0-bus-width1 {
> + samsung,pins = "gpf1-0";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_bus4: sd0-bus-width4 {
> + samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <3>;
> + };
> +
> + sd0_bus8: sd0-bus-width8 {
> + samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <3>;
> + };
> +};
> +
> +&pinctrl_peri {
> + gpg0: gpg0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpp0: gpp0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + gpp1: gpp1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpp2: gpp2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpg1: gpg1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpg2: gpg2 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpg3: gpg3 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpc0: gpc0 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpc1: gpc1 {
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + /* USI: HSI2C0 */
> + hsi2c0_bus: hsi2c0-bus {
> + samsung,pins = "gpc1-0", "gpc1-1";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* USI: HSI2C1 */
> + hsi2c1_bus: hsi2c1-bus {
> + samsung,pins = "gpc1-2", "gpc1-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* USI: HSI2C2 */
> + hsi2c2_bus: hsi2c2-bus {
> + samsung,pins = "gpc1-4", "gpc1-5";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + /* USI: SPI */
> + spi0_bus: spi0-bus {
> + samsung,pins = "gpp2-0", "gpp2-2", "gpp2-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi0_cs: spi0-cs {
> + samsung,pins = "gpp2-1";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + spi0_cs_func: spi0-cs-func {
> + samsung,pins = "gpp2-1";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c0_bus: i2c0-bus {
> + samsung,pins = "gpp0-0", "gpp0-1";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c1_bus: i2c1-bus {
> + samsung,pins = "gpp0-2", "gpp0-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c2_bus: i2c2-bus {
> + samsung,pins = "gpp0-4", "gpp0-5";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c3_bus: i2c3-bus {
> + samsung,pins = "gpp1-0", "gpp1-1";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + i2c4_bus: i2c4-bus {
> + samsung,pins = "gpp1-2", "gpp1-3";
> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> + samsung,pin-drv = <0>;
> + };
> +
> + sensor_mclk0_in: sensor-mclk0-in {
> + samsung,pins = "gpc0-0";
All these gpc0 go before hsi2c0_bus node (to have them ordered by
datasheet pin name).
> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <2>;
> + };
> +
Rest looks good but anyway will wait for the board DTS. :)
Best regards,
Krzysztof
More information about the linux-arm-kernel
mailing list