[PATCH 3/6] perf cs-etm: Save TRCDEVARCH register

[Mike Leach]

Hi Leo,

On Mon, 2 Aug 2021 at 13:05, Leo Yan <leo.yan at linaro.org> wrote:
>
> Hi Mike,
>
> On Mon, Aug 02, 2021 at 12:21:31PM +0100, Mike Leach wrote:
>
> [...]
>
> > > Here I think the right thing to do is to support newer revisions for
> > > ETMv4, and then based on the revision it creates a decoder with
> > > supporting ETE feature.  For a more neat solution, if the perf tool
> > > passes the "correct" revision number to the OpenCSD decoder, it should
> > > can decode trace data with ETE packets.  In this way, the ETE decoding
> > > can be transparent for perf cs-etm code.
> > >
> >
> > The OpenCSD decoder separates the ETMv4 decoder from the ETE decoder -
> > for the reasons given above.
>
> Thanks for explanation.
>
> > Additionally the ETE decoder and the ETMv4 decoder required different
> > sets of ID registers to correctly set up the decoder.  For example,
> > for ETMv4 the version is extracted form TRCIDR1, for ETE the version
> > in TRCIDR1 is set 0xFF, and thus needs TRCDEVARCH to extract the
> > revision. It is likely that later updates to ETE will require an
> > additional TRCIDR register to be saved.
>
> Okay, for ETMv4.x and ETE, finally I think we need to rely on TRCDEVARCH to
> decide the tracer version based on the architecture number (arch 4 or 5)
> and revision number.
>
> > Choosing the base type of decoder in this way is how the library can
> > support ETMv3, EMTv4, ETE, STM, PTM etc - and while some of those
> > protocols use TRCIDR1 and TRCDEVARCH - not all do.
> >
> > It would in theory be possible to have the OpenCSD library
> > "autodetect" the type of decoder needed based purely on a set of ID
> > registers. But this set of ID registers would be far larger than the
> > ones currently used, and would require modifcation to a lot of the
> > existing device drivers to ensure they were accessible via sysfs. This
> > register set includes the ID registers that are currently used to
> > identify the component on the AMBA bus and match to the correct
> > driver, plus additional CoreSight management registers. This would
> > also create a dependency between decoder creation and ID numbers - in
> > the same way that each new ETM4.x part number has to be added to the
> > ETM4.x device driver.
> >
> > Such a system would require a significant update to the OpenCSD
> > infrastructure, and is not planned at this time.
>
> It's fine for me not introducing significant change in OpenCSD.
>
> If so, I understand your suggestion in another email to add a new magic
> number and a new protocol (this patch set has added the new protocol
> CS_ETM_PROTO_ETE) for creating ETE decoder.
>
> Just confirm one thing which is a bit confused me: for ETMv4.5 or any
> newer ETM IPs, should the perf tool keep the existed way to create the
> ETMv4 decoder?  Or there have updating is required for decoder to
> support the extended packets?
>

Where the trace device is identified as an ETMv4.x, then perf will
continue to create an ETMv4.x decoder as it does now. The OpenCSD
ETM4.x decoder will track any needed updates for the ETM4.x series.

Only where the trace device is ETE, there will be the new magic number
and different ID registers be used - so the call to OpenCSD will
request an ETE decoder to be created.

The register value structures supplied to OpenCSD on decoder creation,
differ between ETM4.x and ETE.

Regards

Mike


> Thanks,
> Leo



-- 
Mike Leach
Principal Engineer, ARM Ltd.
Manchester Design Centre. UK