[PATCH v2 6/7] arm64: dts: rockchip: add core dtsi for RK3568 SoC
Johan Jonker
jbx6244 at gmail.com
Mon Apr 26 13:16:45 BST 2021
Hi Liang,
Some minor things to improve.
Found with the command below.
make ARCH=arm64 dtbs_check
===
pwm-rockchip.yaml is now in linux-next
Maybe add rockchip,rk3568-pwm too.
===
compatible = "rockchip,rk3568";
Maybe add this together with other rkXXXX SoCs to rockchip.yaml on top
of board list ???
Please advise.
===
Change rockchip,gpio-bank.yaml
clocks:
maxItems: 2
===
TODO:
rockchip,rk3568-grf
rockchip,rk3568-pmugrf
===
git am
PATCH-v2-5-7-arm64-dts-rockchip-add-generic-pinconfig-settings-used-by-most-Rockchip-socs.patch
Applying: arm64: dts: rockchip: add generic pinconfig settings used by
most Rockchip socs
.git/rebase-apply/patch:356: new blank line at EOF.
+
warning: 1 line adds whitespace errors.
===
Change commit message in:
[PATCH v2 3/7] dt-bindings: mmc: rockchip-dw-mshc: add description for
rk3568
from:
add "rockchip,rk3568-dwcmshc", "snps,dwcmshc-sdhci" for mmc nodes on
a rk3568 platform to rockchip-dw-mshc.yaml.
to:
... "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc" ...
Do not mix dw-mshc and dwcmshc. ;)
===
Johan
On 4/25/21 11:44 AM, cl at rock-chips.com wrote:
> From: Liang Chen <cl at rock-chips.com>
>
> RK3568 is a high-performance and low power quad-core application processor
> designed for personal mobile internet device and AIoT equipments. This patch
> add basic core dtsi file for it.
>
> We use scmi_clk for cortex-a55 instead of standard ARMCLK, so that
> kernel/uboot/rtos can change cpu clk with the same code in ATF, and we will
> enalbe a special high-performacne PLL when high frequency is required. The
> smci_clk code is in ATF, and clkid for cpu is 0, as below:
>
> cpu0: cpu at 0 {
> device_type = "cpu";
> compatible = "arm,cortex-a55";
> reg = <0x0 0x0>;
> clocks = <&scmi_clk 0>;
> };
>
> Signed-off-by: Liang Chen <cl at rock-chips.com>
> ---
> .../boot/dts/rockchip/rk3568-pinctrl.dtsi | 3119 +++++++++++++++++
> arch/arm64/boot/dts/rockchip/rk3568.dtsi | 812 +++++
> 2 files changed, 3931 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3568.dtsi
>
[..]
> +
> + gpio {
>From gpio.yaml
properties:
gpio:
# 'gpio' can appear as a property or node name
oneOf:
- type: object
- $ref: "/schemas/types.yaml#/definitions/phandle-array"
> + /omit-if-no-ref/
> + tsadc_gpio: tsadc-gpio {
>From gpio-consumer.yaml
properties:
gpios:
$ref: "/schemas/types.yaml#/definitions/phandle-array"
patternProperties:
"(?<!,nr)-gpios?$":
$ref: "/schemas/types.yaml#/definitions/phandle-array"
===
Try to avoid anything with gpio.
> + rockchip,pins =
> + <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568.dtsi b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
> new file mode 100644
> index 000000000000..66cb50218ca1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
> @@ -0,0 +1,812 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
> + */
> +
> +#include <dt-bindings/clock/rk3568-cru.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,boot-mode.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + compatible = "rockchip,rk3568";
Maybe add this together with other rkXXXX SoCs to rockchip.yaml on top
of board list ???
Please advise.
> +
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + aliases {
> + gpio0 = &gpio0;
> + gpio1 = &gpio1;
> + gpio2 = &gpio2;
> + gpio3 = &gpio3;
> + gpio4 = &gpio4;
> + i2c0 = &i2c0;
> + i2c1 = &i2c1;
> + i2c2 = &i2c2;
> + i2c3 = &i2c3;
> + i2c4 = &i2c4;
> + i2c5 = &i2c5;
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc0;
> + mmc2 = &sdmmc1;
> + mmc3 = &sdmmc2;
>From a privious discussion: aliases for mmc should go from the dtsi to
the board dts
sort mmc aliases based on reg address and availability, so no number gap
> + serial0 = &uart0;
> + serial1 = &uart1;
> + serial2 = &uart2;
> + serial3 = &uart3;
> + serial4 = &uart4;
> + serial5 = &uart5;
> + serial6 = &uart6;
> + serial7 = &uart7;
> + serial8 = &uart8;
> + serial9 = &uart9;
> + };
> +
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu0: cpu at 0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55";
> + reg = <0x0 0x0>;
> + clocks = <&scmi_clk 0>;
> + enable-method = "psci";
> + operating-points-v2 = <&cpu0_opp_table>;
> + };
> +
> + cpu1: cpu at 100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55";
> + reg = <0x0 0x100>;
> + enable-method = "psci";
> + operating-points-v2 = <&cpu0_opp_table>;
> + };
> +
> + cpu2: cpu at 200 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55";
> + reg = <0x0 0x200>;
> + enable-method = "psci";
> + operating-points-v2 = <&cpu0_opp_table>;
> + };
> +
> + cpu3: cpu at 300 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55";
> + reg = <0x0 0x300>;
> + enable-method = "psci";
> + operating-points-v2 = <&cpu0_opp_table>;
> + };
> + };
> +
> + cpu0_opp_table: cpu0-opp-table {
> + compatible = "operating-points-v2";
> + opp-shared;
> +
> + opp-408000000 {
> + opp-hz = /bits/ 64 <408000000>;
> + opp-microvolt = <825000 825000 1150000>;
> + clock-latency-ns = <40000>;
> + };
Add all empty lines between
> + opp-600000000 {
> + opp-hz = /bits/ 64 <600000000>;
> + opp-microvolt = <825000 825000 1150000>;
> + };
> + opp-816000000 {
> + opp-hz = /bits/ 64 <816000000>;
> + opp-microvolt = <825000 825000 1150000>;
> + opp-suspend;
> + };
> + opp-1104000000 {
> + opp-hz = /bits/ 64 <1104000000>;
> + opp-microvolt = <825000 825000 1150000>;
> + };
> + opp-1416000000 {
> + opp-hz = /bits/ 64 <1416000000>;
> + opp-microvolt = <900000 900000 1150000>;
> + };
> + opp-1608000000 {
> + opp-hz = /bits/ 64 <1608000000>;
> + opp-microvolt = <975000 975000 1150000>;
> + };
> + opp-1800000000 {
> + opp-hz = /bits/ 64 <1800000000>;
> + opp-microvolt = <1050000 1050000 1150000>;
> + };
> + opp-1992000000 {
> + opp-hz = /bits/ 64 <1992000000>;
> + opp-microvolt = <1150000 1150000 1150000>;
> + };
> + };
> +
> + firmware {
> + scmi: scmi {
> + compatible = "arm,scmi-smc";
> + arm,smc-id = <0x82000010>;
> + shmem = <&scmi_shmem>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + scmi_clk: protocol at 14 {
> + reg = <0x14>;
> + #clock-cells = <1>;
> + };
> + };
> +
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a55-pmu", "arm,armv8-pmuv3";
compatible: ['arm,cortex-a55-pmu', 'arm,armv8-pmuv3'] is too long
> + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
> + };
> +
> + psci {
> + compatible = "arm,psci-1.0";
> + method = "smc";
> + };
> +
> + shmem at 10f000 {
shmem at 10f000: $nodename:0: 'shmem at 10f000' does not match '^sram(@.*)?'
> + compatible = "mmio-sram";
> + reg = <0x0 0x0010f000 0x0 0x100>;
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x0010f000 0x100>;
> +
> + scmi_shmem: scmi-shmem at 10f000 {
shmem at 10f000: 'scmi-shmem at 10f000' does not match any of the regexes:
'^([a-z]*-)?sram(-section)?@[a-f0-9]+$'
> + compatible = "arm,scmi-shmem";
> + reg = <0x0 0x0010f000 0x0 0x100>;
> + };
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + arm,no-tick-in-suspend;
> + };
> +
> + xin24m: xin24m {
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "xin24m";
> + #clock-cells = <0>;
> + };
> +
> + xin32k: xin32k {
> + compatible = "fixed-clock";
> + clock-frequency = <32768>;
> + clock-output-names = "xin32k";
> + pinctrl-0 = <&clk32k_out0>;
> + pinctrl-names = "default";
> + #clock-cells = <0>;
> + };
> +
> + gic: interrupt-controller at fd400000 {
> + compatible = "arm,gic-v3";
> + reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
> + <0x0 0xfd460000 0 0xc0000>; /* GICR */
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + #address-cells = <2>;
> + #size-cells = <2>;
subnodes ??
> + ranges;
> + };
> +
> + pmugrf: syscon at fdc20000 {
> + compatible = "rockchip,rk3568-pmugrf", "syscon", "simple-mfd";
TODO
> + reg = <0x0 0xfdc20000 0x0 0x10000>;
> +
> + reboot_mode: reboot-mode {
> + compatible = "syscon-reboot-mode";
> + mode-bootloader = <BOOT_BL_DOWNLOAD>;
> + mode-fastboot = <BOOT_FASTBOOT>;
> + mode-loader = <BOOT_BL_DOWNLOAD>;
> + mode-normal = <BOOT_NORMAL>;
> + mode-recovery = <BOOT_RECOVERY>;
> + offset = <0x200>;
> + };
> + };
> +
> + grf: syscon at fdc60000 {
> + compatible = "rockchip,rk3568-grf", "syscon", "simple-mfd";
TODO
> + reg = <0x0 0xfdc60000 0x0 0x10000>;
> + };
> +
> + pmucru: clock-controller at fdd00000 {
> + compatible = "rockchip,rk3568-pmucru";
> + reg = <0x0 0xfdd00000 0x0 0x1000>;
> + rockchip,grf = <&grf>;
> + rockchip,pmugrf = <&pmugrf>;
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + };
> +
> + cru: clock-controller at fdd20000 {
> + compatible = "rockchip,rk3568-cru";
> + reg = <0x0 0xfdd20000 0x0 0x1000>;
> + rockchip,grf = <&grf>;
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> +
> + assigned-clocks =
> + <&pmucru CLK_RTC_32K>, <&pmucru PLL_PPLL>,
> + <&pmucru PCLK_PMU>, <&cru PLL_CPLL>,
> + <&cru PLL_GPLL>, <&cru ACLK_BUS>,
> + <&cru PCLK_BUS>, <&cru ACLK_TOP_HIGH>,
> + <&cru ACLK_TOP_LOW>, <&cru HCLK_TOP>,
> + <&cru PCLK_TOP>, <&cru ACLK_PERIMID>,
> + <&cru HCLK_PERIMID>, <&cru PLL_NPLL>,
> + <&cru ACLK_PIPE>, <&cru PCLK_PIPE>,
> + <&cru ACLK_VOP>;
> + assigned-clock-rates =
> + <32768>, <200000000>,
> + <100000000>, <1000000000>,
> + <1188000000>, <150000000>,
> + <100000000>, <500000000>,
> + <400000000>, <150000000>,
> + <100000000>, <300000000>,
> + <150000000>, <1200000000>,
> + <400000000>, <100000000>,
> + <500000000>;
> + assigned-clock-parents =
> + <&pmucru CLK_RTC32K_FRAC>;
> + };
> +
> + i2c0: i2c at fdd40000 {
> + compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
> + reg = <0x0 0xfdd40000 0x0 0x1000>;
> + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&pmucru CLK_I2C0>, <&pmucru PCLK_I2C0>;
> + clock-names = "i2c", "pclk";
> + pinctrl-0 = <&i2c0_xfer>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + uart0: serial at fdd50000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfdd50000 0x0 0x100>;
> + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&pmucru SCLK_UART0>, <&pmucru PCLK_UART0>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 0>, <&dmac0 1>;
> + pinctrl-0 = <&uart0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + pwm0: pwm at fdd70000 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfdd70000 0x0 0x10>;
> + clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm0m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm1: pwm at fdd70010 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfdd70010 0x0 0x10>;
> + clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm1m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm2: pwm at fdd70020 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfdd70020 0x0 0x10>;
> + clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm2m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm3: pwm at fdd70030 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfdd70030 0x0 0x10>;
> + clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm3_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + sdmmc2: dwmmc at fe000000 {
dwmmc at fe000000: $nodename:0: 'dwmmc at fe000000' does not match '^mmc(@.*)?$'
> + compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
> + reg = <0x0 0xfe000000 0x0 0x4000>;
> + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru HCLK_SDMMC2>, <&cru CLK_SDMMC2>,
> + <&cru SCLK_SDMMC2_DRV>, <&cru SCLK_SDMMC2_SAMPLE>;
> + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
> + fifo-depth = <0x100>;
> + max-frequency = <150000000>;
> + resets = <&cru SRST_SDMMC2>;
> + reset-names = "reset";
> + status = "disabled";
> + };
> +
> + sdmmc0: dwmmc at fe2b0000 {
dwmmc at fe2b0000: $nodename:0: 'dwmmc at fe2b0000' does not match '^mmc(@.*)?$'
> + compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
> + reg = <0x0 0xfe2b0000 0x0 0x4000>;
> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru HCLK_SDMMC0>, <&cru CLK_SDMMC0>,
> + <&cru SCLK_SDMMC0_DRV>, <&cru SCLK_SDMMC0_SAMPLE>;
> + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
> + fifo-depth = <0x100>;
> + max-frequency = <150000000>;
> + resets = <&cru SRST_SDMMC0>;
> + reset-names = "reset";
> + status = "disabled";
> + };
> +
> + sdmmc1: dwmmc at fe2c0000 {
dwmmc at fe2c0000: $nodename:0: 'dwmmc at fe2c0000' does not match '^mmc(@.*)?$'
> + compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
> + reg = <0x0 0xfe2c0000 0x0 0x4000>;
> + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru HCLK_SDMMC1>, <&cru CLK_SDMMC1>,
> + <&cru SCLK_SDMMC1_DRV>, <&cru SCLK_SDMMC1_SAMPLE>;
> + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
> + fifo-depth = <0x100>;
> + max-frequency = <150000000>;
> + resets = <&cru SRST_SDMMC1>;
> + reset-names = "reset";
> + status = "disabled";
> + };
> +
> + sdhci: sdhci at fe310000 {
sdhci at fe310000: $nodename:0: 'sdhci at fe310000' does not match '^mmc(@.*)?$'
> + compatible = "rockchip,rk3568-dwcmshc";
> + reg = <0x0 0xfe310000 0x0 0x10000>;
> + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
> + assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>;
> + assigned-clock-rates = <200000000>, <24000000>;
> + clocks = <&cru CCLK_EMMC>, <&cru HCLK_EMMC>,
> + <&cru ACLK_EMMC>, <&cru BCLK_EMMC>,
> + <&cru TCLK_EMMC>;
> + clock-names = "core", "bus", "axi", "block", "timer";
> + status = "disabled";
> + };
> +
> + dmac0: dmac at fe530000 {
> + compatible = "arm,pl330", "arm,primecell";
> + reg = <0x0 0xfe530000 0x0 0x4000>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + arm,pl330-periph-burst;
> + clocks = <&cru ACLK_BUS>;
> + clock-names = "apb_pclk";
> + #dma-cells = <1>;
> + };
> +
> + dmac1: dmac at fe550000 {
> + compatible = "arm,pl330", "arm,primecell";
> + reg = <0x0 0xfe550000 0x0 0x4000>;
> + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> + arm,pl330-periph-burst;
> + clocks = <&cru ACLK_BUS>;
> + clock-names = "apb_pclk";
> + #dma-cells = <1>;
> + };
> +
> + i2c1: i2c at fe5a0000 {
> + compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
> + reg = <0x0 0xfe5a0000 0x0 0x1000>;
> + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru CLK_I2C1>, <&cru PCLK_I2C1>;
> + clock-names = "i2c", "pclk";
> + pinctrl-0 = <&i2c1_xfer>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c at fe5b0000 {
> + compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
> + reg = <0x0 0xfe5b0000 0x0 0x1000>;
> + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru CLK_I2C2>, <&cru PCLK_I2C2>;
> + clock-names = "i2c", "pclk";
> + pinctrl-0 = <&i2c2m0_xfer>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c3: i2c at fe5c0000 {
> + compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
> + reg = <0x0 0xfe5c0000 0x0 0x1000>;
> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru CLK_I2C3>, <&cru PCLK_I2C3>;
> + clock-names = "i2c", "pclk";
> + pinctrl-0 = <&i2c3m0_xfer>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c4: i2c at fe5d0000 {
> + compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
> + reg = <0x0 0xfe5d0000 0x0 0x1000>;
> + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru CLK_I2C4>, <&cru PCLK_I2C4>;
> + clock-names = "i2c", "pclk";
> + pinctrl-0 = <&i2c4m0_xfer>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + i2c5: i2c at fe5e0000 {
> + compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
> + reg = <0x0 0xfe5e0000 0x0 0x1000>;
> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru CLK_I2C5>, <&cru PCLK_I2C5>;
> + clock-names = "i2c", "pclk";
> + pinctrl-0 = <&i2c5m0_xfer>;
> + pinctrl-names = "default";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + wdt: watchdog at fe600000 {
> + compatible = "rockchip,rk3568-wdt", "snps,dw-wdt";
> + reg = <0x0 0xfe600000 0x0 0x100>;
> + clocks = <&cru TCLK_WDT_NS>, <&cru PCLK_WDT_NS>;
> + clock-names = "tclk", "pclk";
below interrupts
> + interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + uart1: serial at fe650000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfe650000 0x0 0x100>;
> + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 2>, <&dmac0 3>;
> + pinctrl-0 = <&uart1m0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + uart2: serial at fe660000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfe660000 0x0 0x100>;
> + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 4>, <&dmac0 5>;
> + pinctrl-0 = <&uart2m0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + uart3: serial at fe670000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfe670000 0x0 0x100>;
> + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 6>, <&dmac0 7>;
> + pinctrl-0 = <&uart3m0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + uart4: serial at fe680000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfe680000 0x0 0x100>;
> + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 8>, <&dmac0 9>;
> + pinctrl-0 = <&uart4m0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + uart5: serial at fe690000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfe690000 0x0 0x100>;
> + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru SCLK_UART5>, <&cru PCLK_UART5>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 10>, <&dmac0 11>;
> + pinctrl-0 = <&uart5m0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + uart6: serial at fe6a0000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfe6a0000 0x0 0x100>;
> + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru SCLK_UART6>, <&cru PCLK_UART6>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 12>, <&dmac0 13>;
> + pinctrl-0 = <&uart6m0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + uart7: serial at fe6b0000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfe6b0000 0x0 0x100>;
> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru SCLK_UART7>, <&cru PCLK_UART7>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 14>, <&dmac0 15>;
> + pinctrl-0 = <&uart7m0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + uart8: serial at fe6c0000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfe6c0000 0x0 0x100>;
> + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru SCLK_UART8>, <&cru PCLK_UART8>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 16>, <&dmac0 17>;
> + pinctrl-0 = <&uart8m0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + uart9: serial at fe6d0000 {
> + compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
> + reg = <0x0 0xfe6d0000 0x0 0x100>;
> + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru SCLK_UART9>, <&cru PCLK_UART9>;
> + clock-names = "baudclk", "apb_pclk";
> + dmas = <&dmac0 18>, <&dmac0 19>;
> + pinctrl-0 = <&uart9m0_xfer>;
> + pinctrl-names = "default";
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + status = "disabled";
> + };
> +
> + pwm4: pwm at fe6e0000 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe6e0000 0x0 0x10>;
> + clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm4_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm5: pwm at fe6e0010 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe6e0010 0x0 0x10>;
> + clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm5_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm6: pwm at fe6e0020 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe6e0020 0x0 0x10>;
> + clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm6_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm7: pwm at fe6e0030 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe6e0030 0x0 0x10>;
> + clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm7_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm8: pwm at fe6f0000 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe6f0000 0x0 0x10>;
> + clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm8m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm9: pwm at fe6f0010 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe6f0010 0x0 0x10>;
> + clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm9m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm10: pwm at fe6f0020 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe6f0020 0x0 0x10>;
> + clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm10m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm11: pwm at fe6f0030 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe6f0030 0x0 0x10>;
> + clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm11m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm12: pwm at fe700000 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe700000 0x0 0x10>;
> + clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm12m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm13: pwm at fe700010 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe700010 0x0 0x10>;
> + clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm13m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm14: pwm at fe700020 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe700020 0x0 0x10>;
> + clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm14m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pwm15: pwm at fe700030 {
> + compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
> + reg = <0x0 0xfe700030 0x0 0x10>;
> + clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
> + clock-names = "pwm", "pclk";
> + pinctrl-0 = <&pwm15m0_pins>;
> + pinctrl-names = "active";
> + #pwm-cells = <3>;
> + status = "disabled";
> + };
> +
> + pinctrl: pinctrl {
> + compatible = "rockchip,rk3568-pinctrl";
> + rockchip,grf = <&grf>;
> + rockchip,pmu = <&pmugrf>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + gpio0: gpio at fdd60000 {
> + compatible = "rockchip,gpio-bank";
> + reg = <0x0 0xfdd60000 0x0 0x100>;
> + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&pmucru PCLK_GPIO0>, <&pmucru DBCLK_GPIO0>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpio1: gpio at fe740000 {
> + compatible = "rockchip,gpio-bank";
> + reg = <0x0 0xfe740000 0x0 0x100>;
> + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru PCLK_GPIO1>, <&cru DBCLK_GPIO1>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpio2: gpio at fe750000 {
> + compatible = "rockchip,gpio-bank";
> + reg = <0x0 0xfe750000 0x0 0x100>;
> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru PCLK_GPIO2>, <&cru DBCLK_GPIO2>;
gpio at fe750000: clocks: [[13, 357], [13, 358]] is too long
Change rockchip,gpio-bank.yaml
clocks:
maxItems: 2
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpio3: gpio at fe760000 {
> + compatible = "rockchip,gpio-bank";
> + reg = <0x0 0xfe760000 0x0 0x100>;
> + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru PCLK_GPIO3>, <&cru DBCLK_GPIO3>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpio4: gpio at fe770000 {
> + compatible = "rockchip,gpio-bank";
> + reg = <0x0 0xfe770000 0x0 0x100>;
> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&cru PCLK_GPIO4>, <&cru DBCLK_GPIO4>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +};
> +
> +#include "rk3568-pinctrl.dtsi"
>
More information about the linux-arm-kernel
mailing list