[PATCH v2] arm64: dts: ti: k3-am654-base-board: remove ov5640

Tomi Valkeinen tomi.valkeinen at ideasonboard.com
Fri Apr 23 09:31:20 BST 2021


AM654 EVM boards are not shipped with OV5640 sensor module, it is a
separate purchase. OV5640 module is also just one of the possible
sensors or capture boards you can connect.

However, for some reason, OV5640 has been added to the board dts file,
making it cumbersome to use other sensors.

Remove the OV5640 from the dts file so that it is easy to use other
sensors via DT overlays.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen at ideasonboard.com>
---

Changes in v2:
- drop empty csi2_0 node

A DT overlay with OV5640 can be found from:

https://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux-dt.git/commit/?h=multistream/work&id=ff7a6469a8c40e1fec14f0a186322ee114892117

 .../arm64/boot/dts/ti/k3-am654-base-board.dts | 31 -------------------
 1 file changed, 31 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index fe3043943906..7f27ba7e7256 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -85,12 +85,6 @@ sw6 {
 			gpios = <&wkup_gpio0 27 GPIO_ACTIVE_LOW>;
 		};
 	};
-
-	clk_ov5640_fixed: clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24000000>;
-	};
 };
 
 &wkup_pmx0 {
@@ -287,23 +281,6 @@ &main_i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c1_pins_default>;
 	clock-frequency = <400000>;
-
-	ov5640: camera at 3c {
-		compatible = "ovti,ov5640";
-		reg = <0x3c>;
-
-		clocks = <&clk_ov5640_fixed>;
-		clock-names = "xclk";
-
-		port {
-			csi2_cam0: endpoint {
-				remote-endpoint = <&csi2_phy0>;
-				clock-lanes = <0>;
-				data-lanes = <1 2>;
-			};
-		};
-	};
-
 };
 
 &main_i2c2 {
@@ -496,14 +473,6 @@ flash at 0{
 	};
 };
 
-&csi2_0 {
-	csi2_phy0: endpoint {
-		remote-endpoint = <&csi2_cam0>;
-		clock-lanes = <0>;
-		data-lanes = <1 2>;
-	};
-};
-
 &mcu_cpsw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
-- 
2.25.1




More information about the linux-arm-kernel mailing list