[PATCH 0/2] drm/bridge: dw-hdmi: disable loading of DW-HDMI CEC sub-driver
Laurent Pinchart
laurent.pinchart at ideasonboard.com
Tue Apr 20 23:49:36 BST 2021
On Tue, Apr 20, 2021 at 05:19:52PM +0200, Neil Armstrong wrote:
> On 20/04/2021 17:13, Hans Verkuil wrote:
> > On 16/04/2021 13:38, Neil Armstrong wrote:
> >> On 16/04/2021 11:58, Laurent Pinchart wrote:
> >>> Hi Neil,
> >>>
> >>> On Fri, Apr 16, 2021 at 11:27:35AM +0200, Neil Armstrong wrote:
> >>>> This adds DW-HDMI driver a glue option to disable loading of the CEC sub-driver.
> >>>>
> >>>> On some SoCs, the CEC functionality is enabled in the IP config bits, but the
> >>>> CEC bus is non-functional like on Amlogic SoCs, where the CEC config bit is set
> >>>> but the DW-HDMI CEC signal is not connected to a physical pin, leading to some
> >>>> confusion when the DW-HDMI CEC controller can't communicate on the bus.
> >>>
> >>> If we can't trust the CEC config bit, would it be better to not use it
> >>> at all, and instead let each platform glue logic tell whether to enable
> >>> CEC or not ?
> >>
> >> Actually, the CEC config bit is right, the HW exists and should be functional, but
> >> this bit doesn't tell if the CEC signal is connected to something.
> >>
> >> This lies in the IP integration, like other bits under the "amlogic,meson-*-dw-hdmi"
> >> umbrella.
> >>
> >> The first attempt was by Hans using DT, but adding a property in DT for a vendor
> >> specific compatible doesn't make sense. Another idea would be to describe the
> >> CEC signal endpoint like we do for video signal, but I think this is out of scope and
> >> this solution is much simpler and straightforward, and it's more an exception than
> >> a general use case to solve.
> >
> > While a DT property might not make sense in this particular case, I still
> > believe that it is a perfectly valid approach in general: whether or not
> > the CEC pin is connected is at the hardware level decision, it is not
> > something that software can detect. If the designer of the board didn't
> > connect it, then the only place you can define that is in the device tree.
>
> Agreed, we need to define a smart way to declare CEC bus relationship in DT, the side
> effect would be to handle this particular case.
I wonder if it would make sense to use the OF graph bindings to describe
the connection between the CEC controller and the CEC "device" (which I
assume in most cases will be a DT node for a physical connector). Or is
this overkill ?
> > Anyway, for meson I am fine with this solution. At least it prevents creating
> > a non-functioning cec device. So for this series:
> >
> > Acked-by: Hans Verkuil <hverkuil-cisco at xs4all.nl>
>
> Thanks,
>
> Applying this serie to drm-misc-next
>
> >>>> Jernej Skrabec (1):
> >>>> drm/bridge/synopsys: dw-hdmi: Add an option to suppress loading CEC
> >>>> driver
> >>>>
> >>>> Neil Armstrong (1):
> >>>> drm/meson: dw-hdmi: disable DW-HDMI CEC sub-driver
> >>>>
> >>>> drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 2 +-
> >>>> drivers/gpu/drm/meson/meson_dw_hdmi.c | 1 +
> >>>> include/drm/bridge/dw_hdmi.h | 2 ++
> >>>> 3 files changed, 4 insertions(+), 1 deletion(-)
--
Regards,
Laurent Pinchart
More information about the linux-arm-kernel
mailing list