[PATCH net-next 10/10] arm64: dts: sparx5: Add the Sparx5 switch node
Steen Hegelund
steen.hegelund at microchip.com
Fri Apr 16 14:16:57 BST 2021
This provides the configuration for the currently available evaluation
boards PCB134 and PCB135.
The series depends on the following series currently on their way
into the kernel:
- Sparx5 SerDes Driver
Link: https://lore.kernel.org/r/20210218161451.3489955-1-steen.hegelund@microchip.com/
- Sparx5 Reset Driver
Link: https://lore.kernel.org/r/20210416084054.2922327-1-steen.hegelund@microchip.com/
- Serial GPIO Controller
Link: https://lore.kernel.org/r/20201113145151.68900-1-lars.povlsen@microchip.com/
Signed-off-by: Steen Hegelund <steen.hegelund at microchip.com>
Signed-off-by: Lars Povlsen <lars.povlsen at microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson at microchip.com>
---
arch/arm64/boot/dts/microchip/sparx5.dtsi | 94 ++-
.../dts/microchip/sparx5_pcb134_board.dtsi | 481 ++++++++++++--
.../dts/microchip/sparx5_pcb135_board.dtsi | 621 +++++++++++++++++-
3 files changed, 1112 insertions(+), 84 deletions(-)
diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index d64621d1213b..ad07fff40544 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -135,9 +135,12 @@ mux: mux-controller {
};
};
- reset at 611010008 {
- compatible = "microchip,sparx5-chip-reset";
+ reset: reset-controller at 611010008 {
+ compatible = "microchip,sparx5-switch-reset";
reg = <0x6 0x11010008 0x4>;
+ reg-names = "gcb";
+ #reset-cells = <1>;
+ cpu-syscon = <&cpu_ctrl>;
};
uart0: serial at 600100000 {
@@ -275,6 +278,21 @@ emmc_pins: emmc-pins {
"GPIO_46", "GPIO_47";
function = "emmc";
};
+
+ miim1_pins: miim1-pins {
+ pins = "GPIO_56", "GPIO_57";
+ function = "miim";
+ };
+
+ miim2_pins: miim2-pins {
+ pins = "GPIO_58", "GPIO_59";
+ function = "miim";
+ };
+
+ miim3_pins: miim3-pins {
+ pins = "GPIO_52", "GPIO_53";
+ function = "miim";
+ };
};
sgpio0: gpio at 61101036c {
@@ -285,6 +303,8 @@ sgpio0: gpio at 61101036c {
clocks = <&sys_clk>;
pinctrl-0 = <&sgpio0_pins>;
pinctrl-names = "default";
+ resets = <&reset 0>;
+ reset-names = "switch";
reg = <0x6 0x1101036c 0x100>;
sgpio_in0: gpio at 0 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -292,6 +312,9 @@ sgpio_in0: gpio at 0 {
gpio-controller;
#gpio-cells = <3>;
ngpios = <96>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
};
sgpio_out0: gpio at 1 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -310,6 +333,8 @@ sgpio1: gpio at 611010484 {
clocks = <&sys_clk>;
pinctrl-0 = <&sgpio1_pins>;
pinctrl-names = "default";
+ resets = <&reset 0>;
+ reset-names = "switch";
reg = <0x6 0x11010484 0x100>;
sgpio_in1: gpio at 0 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -317,6 +342,9 @@ sgpio_in1: gpio at 0 {
gpio-controller;
#gpio-cells = <3>;
ngpios = <96>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
};
sgpio_out1: gpio at 1 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -335,6 +363,8 @@ sgpio2: gpio at 61101059c {
clocks = <&sys_clk>;
pinctrl-0 = <&sgpio2_pins>;
pinctrl-names = "default";
+ resets = <&reset 0>;
+ reset-names = "switch";
reg = <0x6 0x1101059c 0x100>;
sgpio_in2: gpio at 0 {
reg = <0>;
@@ -342,6 +372,9 @@ sgpio_in2: gpio at 0 {
gpio-controller;
#gpio-cells = <3>;
ngpios = <96>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
};
sgpio_out2: gpio at 1 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -386,5 +419,62 @@ tmon0: tmon at 610508110 {
#thermal-sensor-cells = <0>;
clocks = <&ahb_clk>;
};
+
+ mdio0: mdio at 6110102b0 {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x110102b0 0x24>;
+ };
+
+ mdio1: mdio at 6110102d4 {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ pinctrl-0 = <&miim1_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x110102d4 0x24>;
+ };
+
+ mdio2: mdio at 6110102f8 {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ pinctrl-0 = <&miim2_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x110102d4 0x24>;
+ };
+
+ mdio3: mdio at 61101031c {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ pinctrl-0 = <&miim3_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x1101031c 0x24>;
+ };
+
+ serdes: serdes at 10808000 {
+ compatible = "microchip,sparx5-serdes";
+ #phy-cells = <1>;
+ clocks = <&sys_clk>;
+ reg = <0x6 0x10808000 0x5d0000>;
+ };
+
+ switch: switch at 0x600000000 {
+ compatible = "microchip,sparx5-switch";
+ reg = <0x6 0 0x401000>,
+ <0x6 0x10004000 0x7fc000>,
+ <0x6 0x11010000 0xaf0000>;
+ reg-names = "cpu", "dev", "gcb";
+ interrupt-names = "xtr";
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&reset 0>;
+ reset-names = "switch";
+ };
};
};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index f0c915160990..33faf1f3264f 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -7,30 +7,6 @@
#include "sparx5_pcb_common.dtsi"
/{
- aliases {
- i2c0 = &i2c0;
- i2c100 = &i2c100;
- i2c101 = &i2c101;
- i2c102 = &i2c102;
- i2c103 = &i2c103;
- i2c104 = &i2c104;
- i2c105 = &i2c105;
- i2c106 = &i2c106;
- i2c107 = &i2c107;
- i2c108 = &i2c108;
- i2c109 = &i2c109;
- i2c110 = &i2c110;
- i2c111 = &i2c111;
- i2c112 = &i2c112;
- i2c113 = &i2c113;
- i2c114 = &i2c114;
- i2c115 = &i2c115;
- i2c116 = &i2c116;
- i2c117 = &i2c117;
- i2c118 = &i2c118;
- i2c119 = &i2c119;
- };
-
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -298,17 +274,10 @@ gpio at 1 {
&spi0 {
status = "okay";
- spi at 0 {
- compatible = "spi-mux";
- mux-controls = <&mux>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>; /* CS0 */
- spi-flash at 9 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <8000000>;
- reg = <0x9>; /* SPI */
- };
+ spi-flash at 0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <8000000>;
+ reg = <0>;
};
};
@@ -328,6 +297,33 @@ spi-flash at 9 {
};
};
+&sgpio0 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <8 15>;
+ gpio at 0 {
+ ngpios = <64>;
+ };
+ gpio at 1 {
+ ngpios = <64>;
+ };
+};
+
+&sgpio1 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <24 31>;
+ gpio at 0 {
+ ngpios = <64>;
+ };
+ gpio at 1 {
+ ngpios = <64>;
+ };
+};
+
+&sgpio2 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <0 0>, <11 31>;
+};
+
&gpio {
i2cmux_pins_i: i2cmux-pins-i {
pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19",
@@ -415,9 +411,9 @@ i2c0_emux: i2c0-emux at 0 {
&i2c0_imux {
pinctrl-names =
- "i2c100", "i2c101", "i2c102", "i2c103",
- "i2c104", "i2c105", "i2c106", "i2c107",
- "i2c108", "i2c109", "i2c110", "i2c111", "idle";
+ "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
+ "i2c_sfp5", "i2c_sfp6", "i2c_sfp7", "i2c_sfp8",
+ "i2c_sfp9", "i2c_sfp10", "i2c_sfp11", "i2c_sfp12", "idle";
pinctrl-0 = <&i2cmux_0>;
pinctrl-1 = <&i2cmux_1>;
pinctrl-2 = <&i2cmux_2>;
@@ -431,62 +427,62 @@ &i2c0_imux {
pinctrl-10 = <&i2cmux_10>;
pinctrl-11 = <&i2cmux_11>;
pinctrl-12 = <&i2cmux_pins_i>;
- i2c100: i2c_sfp1 {
+ i2c_sfp1: i2c_sfp1 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c101: i2c_sfp2 {
+ i2c_sfp2: i2c_sfp2 {
reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c102: i2c_sfp3 {
+ i2c_sfp3: i2c_sfp3 {
reg = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c103: i2c_sfp4 {
+ i2c_sfp4: i2c_sfp4 {
reg = <0x3>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c104: i2c_sfp5 {
+ i2c_sfp5: i2c_sfp5 {
reg = <0x4>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c105: i2c_sfp6 {
+ i2c_sfp6: i2c_sfp6 {
reg = <0x5>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c106: i2c_sfp7 {
+ i2c_sfp7: i2c_sfp7 {
reg = <0x6>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c107: i2c_sfp8 {
+ i2c_sfp8: i2c_sfp8 {
reg = <0x7>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c108: i2c_sfp9 {
+ i2c_sfp9: i2c_sfp9 {
reg = <0x8>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c109: i2c_sfp10 {
+ i2c_sfp10: i2c_sfp10 {
reg = <0x9>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c110: i2c_sfp11 {
+ i2c_sfp11: i2c_sfp11 {
reg = <0xa>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c111: i2c_sfp12 {
+ i2c_sfp12: i2c_sfp12 {
reg = <0xb>;
#address-cells = <1>;
#size-cells = <0>;
@@ -499,44 +495,413 @@ &gpio 60 GPIO_ACTIVE_HIGH
&gpio 61 GPIO_ACTIVE_HIGH
&gpio 54 GPIO_ACTIVE_HIGH>;
idle-state = <0x8>;
- i2c112: i2c_sfp13 {
+ i2c_sfp13: i2c_sfp13 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c113: i2c_sfp14 {
+ i2c_sfp14: i2c_sfp14 {
reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c114: i2c_sfp15 {
+ i2c_sfp15: i2c_sfp15 {
reg = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c115: i2c_sfp16 {
+ i2c_sfp16: i2c_sfp16 {
reg = <0x3>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c116: i2c_sfp17 {
+ i2c_sfp17: i2c_sfp17 {
reg = <0x4>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c117: i2c_sfp18 {
+ i2c_sfp18: i2c_sfp18 {
reg = <0x5>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c118: i2c_sfp19 {
+ i2c_sfp19: i2c_sfp19 {
reg = <0x6>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c119: i2c_sfp20 {
+ i2c_sfp20: i2c_sfp20 {
reg = <0x7>;
#address-cells = <1>;
#size-cells = <0>;
};
};
+
+&mdio3 {
+ status = "ok";
+ phy64: ethernet-phy at 64 {
+ reg = <28>;
+ };
+};
+
+&axi {
+ sfp_eth12: sfp-eth12 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp1>;
+ tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth13: sfp-eth13 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp2>;
+ tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth14: sfp-eth14 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp3>;
+ tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth15: sfp-eth15 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp4>;
+ tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth48: sfp-eth48 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp5>;
+ tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth49: sfp-eth49 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp6>;
+ tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth50: sfp-eth50 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp7>;
+ tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth51: sfp-eth51 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp8>;
+ tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth52: sfp-eth52 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp9>;
+ tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth53: sfp-eth53 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp10>;
+ tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth54: sfp-eth54 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp11>;
+ tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth55: sfp-eth55 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp12>;
+ tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth56: sfp-eth56 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp13>;
+ tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth57: sfp-eth57 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp14>;
+ tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth58: sfp-eth58 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp15>;
+ tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth59: sfp-eth59 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp16>;
+ tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth60: sfp-eth60 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp17>;
+ tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth61: sfp-eth61 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp18>;
+ tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth62: sfp-eth62 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp19>;
+ tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth63: sfp-eth63 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp20>;
+ tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 10G SFPs */
+ port12: port at 12 {
+ reg = <12>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 13>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth12>;
+ microchip,sd-sgpio = <301>;
+ managed = "in-band-status";
+ };
+ port13: port at 13 {
+ reg = <13>;
+ /* Example: CU SFP, 1G speed */
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 14>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth13>;
+ microchip,sd-sgpio = <305>;
+ managed = "in-band-status";
+ };
+ port14: port at 14 {
+ reg = <14>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 15>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth14>;
+ microchip,sd-sgpio = <309>;
+ managed = "in-band-status";
+ };
+ port15: port at 15 {
+ reg = <15>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 16>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth15>;
+ microchip,sd-sgpio = <313>;
+ managed = "in-band-status";
+ };
+ port48: port at 48 {
+ reg = <48>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 17>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth48>;
+ microchip,sd-sgpio = <317>;
+ managed = "in-band-status";
+ };
+ port49: port at 49 {
+ reg = <49>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 18>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth49>;
+ microchip,sd-sgpio = <321>;
+ managed = "in-band-status";
+ };
+ port50: port at 50 {
+ reg = <50>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 19>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth50>;
+ microchip,sd-sgpio = <325>;
+ managed = "in-band-status";
+ };
+ port51: port at 51 {
+ reg = <51>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 20>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth51>;
+ microchip,sd-sgpio = <329>;
+ managed = "in-band-status";
+ };
+ port52: port at 52 {
+ reg = <52>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 21>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth52>;
+ microchip,sd-sgpio = <333>;
+ managed = "in-band-status";
+ };
+ port53: port at 53 {
+ reg = <53>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 22>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth53>;
+ microchip,sd-sgpio = <337>;
+ managed = "in-band-status";
+ };
+ port54: port at 54 {
+ reg = <54>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 23>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth54>;
+ microchip,sd-sgpio = <341>;
+ managed = "in-band-status";
+ };
+ port55: port at 55 {
+ reg = <55>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 24>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth55>;
+ microchip,sd-sgpio = <345>;
+ managed = "in-band-status";
+ };
+ /* 25G SFPs */
+ port56: port at 56 {
+ reg = <56>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 25>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth56>;
+ microchip,sd-sgpio = <349>;
+ managed = "in-band-status";
+ };
+ port57: port at 57 {
+ reg = <57>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 26>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth57>;
+ microchip,sd-sgpio = <353>;
+ managed = "in-band-status";
+ };
+ port58: port at 58 {
+ reg = <58>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 27>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth58>;
+ microchip,sd-sgpio = <357>;
+ managed = "in-band-status";
+ };
+ port59: port at 59 {
+ reg = <59>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 28>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth59>;
+ microchip,sd-sgpio = <361>;
+ managed = "in-band-status";
+ };
+ port60: port at 60 {
+ reg = <60>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 29>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth60>;
+ microchip,sd-sgpio = <365>;
+ managed = "in-band-status";
+ };
+ port61: port at 61 {
+ reg = <61>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 30>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth61>;
+ microchip,sd-sgpio = <369>;
+ managed = "in-band-status";
+ };
+ port62: port at 62 {
+ reg = <62>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 31>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth62>;
+ microchip,sd-sgpio = <373>;
+ managed = "in-band-status";
+ };
+ port63: port at 63 {
+ reg = <63>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 32>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth63>;
+ microchip,sd-sgpio = <377>;
+ managed = "in-band-status";
+ };
+ /* Finally the Management interface */
+ port64: port at 64 {
+ reg = <64>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 0>;
+ phy-handle = <&phy64>;
+ phy-mode = "sgmii";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index e28c6dd16377..ef96e6d8c6b3 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -7,14 +7,6 @@
#include "sparx5_pcb_common.dtsi"
/{
- aliases {
- i2c0 = &i2c0;
- i2c152 = &i2c152;
- i2c153 = &i2c153;
- i2c154 = &i2c154;
- i2c155 = &i2c155;
- };
-
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -97,17 +89,10 @@ i2cmux_s32: i2cmux-3 {
&spi0 {
status = "okay";
- spi at 0 {
- compatible = "spi-mux";
- mux-controls = <&mux>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>; /* CS0 */
- spi-flash at 9 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <8000000>;
- reg = <0x9>; /* SPI */
- };
+ spi-flash at 0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <8000000>;
+ reg = <0>;
};
};
@@ -138,6 +123,11 @@ gpio at 1 {
};
};
+&sgpio2 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
+};
+
&axi {
i2c0_imux: i2c0-imux at 0 {
compatible = "i2c-mux-pinctrl";
@@ -149,31 +139,614 @@ i2c0_imux: i2c0-imux at 0 {
&i2c0_imux {
pinctrl-names =
- "i2c152", "i2c153", "i2c154", "i2c155",
+ "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
"idle";
pinctrl-0 = <&i2cmux_s29>;
pinctrl-1 = <&i2cmux_s30>;
pinctrl-2 = <&i2cmux_s31>;
pinctrl-3 = <&i2cmux_s32>;
pinctrl-4 = <&i2cmux_pins_i>;
- i2c152: i2c_sfp1 {
+ i2c_sfp1: i2c_sfp1 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c153: i2c_sfp2 {
+ i2c_sfp2: i2c_sfp2 {
reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c154: i2c_sfp3 {
+ i2c_sfp3: i2c_sfp3 {
reg = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c155: i2c_sfp4 {
+ i2c_sfp4: i2c_sfp4 {
reg = <0x3>;
#address-cells = <1>;
#size-cells = <0>;
};
};
+
+&axi {
+ sfp_eth60: sfp-eth60 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp1>;
+ tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth61: sfp-eth61 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp2>;
+ tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth62: sfp-eth62 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp3>;
+ tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth63: sfp-eth63 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp4>;
+ tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&mdio0 {
+ status = "ok";
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+ phy2: ethernet-phy at 2 {
+ reg = <2>;
+ };
+ phy3: ethernet-phy at 3 {
+ reg = <3>;
+ };
+ phy4: ethernet-phy at 4 {
+ reg = <4>;
+ };
+ phy5: ethernet-phy at 5 {
+ reg = <5>;
+ };
+ phy6: ethernet-phy at 6 {
+ reg = <6>;
+ };
+ phy7: ethernet-phy at 7 {
+ reg = <7>;
+ };
+ phy8: ethernet-phy at 8 {
+ reg = <8>;
+ };
+ phy9: ethernet-phy at 9 {
+ reg = <9>;
+ };
+ phy10: ethernet-phy at 10 {
+ reg = <10>;
+ };
+ phy11: ethernet-phy at 11 {
+ reg = <11>;
+ };
+ phy12: ethernet-phy at 12 {
+ reg = <12>;
+ };
+ phy13: ethernet-phy at 13 {
+ reg = <13>;
+ };
+ phy14: ethernet-phy at 14 {
+ reg = <14>;
+ };
+ phy15: ethernet-phy at 15 {
+ reg = <15>;
+ };
+ phy16: ethernet-phy at 16 {
+ reg = <16>;
+ };
+ phy17: ethernet-phy at 17 {
+ reg = <17>;
+ };
+ phy18: ethernet-phy at 18 {
+ reg = <18>;
+ };
+ phy19: ethernet-phy at 19 {
+ reg = <19>;
+ };
+ phy20: ethernet-phy at 20 {
+ reg = <20>;
+ };
+ phy21: ethernet-phy at 21 {
+ reg = <21>;
+ };
+ phy22: ethernet-phy at 22 {
+ reg = <22>;
+ };
+ phy23: ethernet-phy at 23 {
+ reg = <23>;
+ };
+};
+
+&mdio1 {
+ status = "ok";
+ phy24: ethernet-phy at 24 {
+ reg = <0>;
+ };
+ phy25: ethernet-phy at 25 {
+ reg = <1>;
+ };
+ phy26: ethernet-phy at 26 {
+ reg = <2>;
+ };
+ phy27: ethernet-phy at 27 {
+ reg = <3>;
+ };
+ phy28: ethernet-phy at 28 {
+ reg = <4>;
+ };
+ phy29: ethernet-phy at 29 {
+ reg = <5>;
+ };
+ phy30: ethernet-phy at 30 {
+ reg = <6>;
+ };
+ phy31: ethernet-phy at 31 {
+ reg = <7>;
+ };
+ phy32: ethernet-phy at 32 {
+ reg = <8>;
+ };
+ phy33: ethernet-phy at 33 {
+ reg = <9>;
+ };
+ phy34: ethernet-phy at 34 {
+ reg = <10>;
+ };
+ phy35: ethernet-phy at 35 {
+ reg = <11>;
+ };
+ phy36: ethernet-phy at 36 {
+ reg = <12>;
+ };
+ phy37: ethernet-phy at 37 {
+ reg = <13>;
+ };
+ phy38: ethernet-phy at 38 {
+ reg = <14>;
+ };
+ phy39: ethernet-phy at 39 {
+ reg = <15>;
+ };
+ phy40: ethernet-phy at 40 {
+ reg = <16>;
+ };
+ phy41: ethernet-phy at 41 {
+ reg = <17>;
+ };
+ phy42: ethernet-phy at 42 {
+ reg = <18>;
+ };
+ phy43: ethernet-phy at 43 {
+ reg = <19>;
+ };
+ phy44: ethernet-phy at 44 {
+ reg = <20>;
+ };
+ phy45: ethernet-phy at 45 {
+ reg = <21>;
+ };
+ phy46: ethernet-phy at 46 {
+ reg = <22>;
+ };
+ phy47: ethernet-phy at 47 {
+ reg = <23>;
+ };
+};
+
+&mdio3 {
+ status = "ok";
+ phy64: ethernet-phy at 64 {
+ reg = <28>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port at 0 {
+ reg = <0>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy0>;
+ phy-mode = "qsgmii";
+ };
+ port1: port at 1 {
+ reg = <1>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy1>;
+ phy-mode = "qsgmii";
+ };
+ port2: port at 2 {
+ reg = <2>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy2>;
+ phy-mode = "qsgmii";
+ };
+ port3: port at 3 {
+ reg = <3>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy3>;
+ phy-mode = "qsgmii";
+ };
+ port4: port at 4 {
+ reg = <4>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy4>;
+ phy-mode = "qsgmii";
+ };
+ port5: port at 5 {
+ reg = <5>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy5>;
+ phy-mode = "qsgmii";
+ };
+ port6: port at 6 {
+ reg = <6>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy6>;
+ phy-mode = "qsgmii";
+ };
+ port7: port at 7 {
+ reg = <7>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy7>;
+ phy-mode = "qsgmii";
+ };
+ port8: port at 8 {
+ reg = <8>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy8>;
+ phy-mode = "qsgmii";
+ };
+ port9: port at 9 {
+ reg = <9>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy9>;
+ phy-mode = "qsgmii";
+ };
+ port10: port at 10 {
+ reg = <10>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy10>;
+ phy-mode = "qsgmii";
+ };
+ port11: port at 11 {
+ reg = <11>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy11>;
+ phy-mode = "qsgmii";
+ };
+ port12: port at 12 {
+ reg = <12>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy12>;
+ phy-mode = "qsgmii";
+ };
+ port13: port at 13 {
+ reg = <13>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy13>;
+ phy-mode = "qsgmii";
+ };
+ port14: port at 14 {
+ reg = <14>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy14>;
+ phy-mode = "qsgmii";
+ };
+ port15: port at 15 {
+ reg = <15>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy15>;
+ phy-mode = "qsgmii";
+ };
+ port16: port at 16 {
+ reg = <16>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy16>;
+ phy-mode = "qsgmii";
+ };
+ port17: port at 17 {
+ reg = <17>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy17>;
+ phy-mode = "qsgmii";
+ };
+ port18: port at 18 {
+ reg = <18>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy18>;
+ phy-mode = "qsgmii";
+ };
+ port19: port at 19 {
+ reg = <19>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy19>;
+ phy-mode = "qsgmii";
+ };
+ port20: port at 20 {
+ reg = <20>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy20>;
+ phy-mode = "qsgmii";
+ };
+ port21: port at 21 {
+ reg = <21>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy21>;
+ phy-mode = "qsgmii";
+ };
+ port22: port at 22 {
+ reg = <22>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy22>;
+ phy-mode = "qsgmii";
+ };
+ port23: port at 23 {
+ reg = <23>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy23>;
+ phy-mode = "qsgmii";
+ };
+ port24: port at 24 {
+ reg = <24>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy24>;
+ phy-mode = "qsgmii";
+ };
+ port25: port at 25 {
+ reg = <25>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy25>;
+ phy-mode = "qsgmii";
+ };
+ port26: port at 26 {
+ reg = <26>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy26>;
+ phy-mode = "qsgmii";
+ };
+ port27: port at 27 {
+ reg = <27>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy27>;
+ phy-mode = "qsgmii";
+ };
+ port28: port at 28 {
+ reg = <28>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy28>;
+ phy-mode = "qsgmii";
+ };
+ port29: port at 29 {
+ reg = <29>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy29>;
+ phy-mode = "qsgmii";
+ };
+ port30: port at 30 {
+ reg = <30>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy30>;
+ phy-mode = "qsgmii";
+ };
+ port31: port at 31 {
+ reg = <31>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy31>;
+ phy-mode = "qsgmii";
+ };
+ port32: port at 32 {
+ reg = <32>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy32>;
+ phy-mode = "qsgmii";
+ };
+ port33: port at 33 {
+ reg = <33>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy33>;
+ phy-mode = "qsgmii";
+ };
+ port34: port at 34 {
+ reg = <34>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy34>;
+ phy-mode = "qsgmii";
+ };
+ port35: port at 35 {
+ reg = <35>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy35>;
+ phy-mode = "qsgmii";
+ };
+ port36: port at 36 {
+ reg = <36>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy36>;
+ phy-mode = "qsgmii";
+ };
+ port37: port at 37 {
+ reg = <37>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy37>;
+ phy-mode = "qsgmii";
+ };
+ port38: port at 38 {
+ reg = <38>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy38>;
+ phy-mode = "qsgmii";
+ };
+ port39: port at 39 {
+ reg = <39>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy39>;
+ phy-mode = "qsgmii";
+ };
+ port40: port at 40 {
+ reg = <40>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy40>;
+ phy-mode = "qsgmii";
+ };
+ port41: port at 41 {
+ reg = <41>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy41>;
+ phy-mode = "qsgmii";
+ };
+ port42: port at 42 {
+ reg = <42>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy42>;
+ phy-mode = "qsgmii";
+ };
+ port43: port at 43 {
+ reg = <43>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy43>;
+ phy-mode = "qsgmii";
+ };
+ port44: port at 44 {
+ reg = <44>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy44>;
+ phy-mode = "qsgmii";
+ };
+ port45: port at 45 {
+ reg = <45>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy45>;
+ phy-mode = "qsgmii";
+ };
+ port46: port at 46 {
+ reg = <46>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy46>;
+ phy-mode = "qsgmii";
+ };
+ port47: port at 47 {
+ reg = <47>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy47>;
+ phy-mode = "qsgmii";
+ };
+ /* Then the 25G interfaces */
+ port60: port at 60 {
+ reg = <60>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 29>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth60>;
+ managed = "in-band-status";
+ };
+ port61: port at 61 {
+ reg = <61>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 30>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth61>;
+ managed = "in-band-status";
+ };
+ port62: port at 62 {
+ reg = <62>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 31>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth62>;
+ managed = "in-band-status";
+ };
+ port63: port at 63 {
+ reg = <63>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 32>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth63>;
+ managed = "in-band-status";
+ };
+ /* Finally the Management interface */
+ port64: port at 64 {
+ reg = <64>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 0>;
+ phy-handle = <&phy64>;
+ phy-mode = "sgmii";
+ };
+ };
+};
--
2.31.1
More information about the linux-arm-kernel
mailing list