[PATCH 7/7] ARM: dts: stm32: Switch DWMAC RMII clock to MCO2 on DHCOM

[Marek Vasut]

The DHCOM SoM has two options for supplying ETHRX clock to the DWMAC
block and PHY. Either (1) ETHCK_K generates 50 MHz clock on ETH_CLK
pad for the PHY and the same 50 MHz clock are fed back to ETHRX via
internal eth_clk_fb clock connection OR (2) ETH_CLK is not used at
all, MCO2 generates 50 MHz clock on MCO2 output pad for the PHY and
the same MCO2 clock are fed back into ETHRX via ETH_RX_CLK input pad
using external pad-to-pad connection.

Option (1) has two downsides. ETHCK_K is supplied directly from either
PLL3_Q or PLL4_P, hence the PLL output is limited to exactly 50 MHz and
since the same PLL output is also used to supply SDMMC blocks, the
performance of SD and eMMC access is affected. The second downside is
that using this option, the EMI of the SoM is higher.

Option (2) solves both of those problems, so implement it here. In this
case, the PLL4_P is no longer limited and can be operated faster, at
100 MHz, which improves SDMMC performance (read performance is improved
from ~41 MiB/s to ~57 MiB/s with dd if=/dev/mmcblk1 of=/dev/null bs=64M
count=1). The EMI interference also decreases.

Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Alexandre Torgue <alexandre.torgue at foss.st.com>
Cc: Christophe Roullier <christophe.roullier at foss.st.com>
Cc: Gabriel Fernandez <gabriel.fernandez at foss.st.com>
Cc: Patrice Chotard <patrice.chotard at foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay at foss.st.com>
Cc: Stephen Boyd <swboyd at chromium.org>
Cc: linux-clk at vger.kernel.org
Cc: linux-stm32 at st-md-mailman.stormreply.com
To: linux-arm-kernel at lists.infradead.org
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 20 +++++++++++++++++---
 1 file changed, 17 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index 272a1a67a9ad..4c7c06a7aea0 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -114,15 +114,29 @@ &dts {
 	status = "okay";
 };
 
+&rcc {
+	/* Connect MCO2 output to ETH_RX_CLK input via pad-pad connection */
+	clocks = <&rcc CK_MCO2>;
+	clock-names = "ETH_RX_CLK/ETH_REF_CLK";
+
+	/*
+	 * Set PLL4P output to 100 MHz to supply SDMMC with faster clock,
+	 * set MCO2 output to 50 MHz to supply ETHRX clock with PLL4P/2,
+	 * so that MCO2 behaves as a divider for the ETHRX clock here.
+	 */
+	assigned-clocks = <&rcc CK_MCO2>, <&rcc PLL4_P>;
+	assigned-clock-parents = <&rcc PLL4_P>;
+	assigned-clock-rates = <50000000>, <100000000>;
+};
+
 &ethernet0 {
 	status = "okay";
-	pinctrl-0 = <&ethernet0_rmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
+	pinctrl-0 = <&ethernet0_rmii_pins_b &mco2_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_b &mco2_sleep_pins_a>;
 	pinctrl-names = "default", "sleep";
 	phy-mode = "rmii";
 	max-speed = <100>;
 	phy-handle = <&phy0>;
-	st,eth-ref-clk-sel;
 	phy-reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
 
 	mdio0 {
-- 
2.30.2