[RFC PATCH 00/10] irqchip/irq-gic: Optimize masking by leveraging EOImode=1

[Valentin Schneider]

Hi folks!

This is the spiritual successor to [1], which was over 6 years ago (!).

Background
==========

GIC mechanics
+++++++++++++

There are three IRQ operations:
o Acknowledge. This gives us the IRQ number that interrupted us, and also
  - raises the running priority of the CPU interface to that of the IRQ
  - sets the active bit of the IRQ
o Priority Drop. This "clears" the running priority.
o Deactivate. This clears the active bit of the IRQ.

o The CPU interface has a running priority value. No interrupt of lower or
  equal priority will be signaled to the CPU attached to that interface. On
  Linux, we only have two priority values: pNMIs at highest priority, and
  everything else at the other priority.
o Most GIC interrupts have an "active" bit. This bit is set on Acknowledge
  and cleared on Deactivate. A given interrupt cannot be re-signaled to a
  CPU if it has its active bit set (i.e. if it "fires" again while it's
  being handled).

EOImode fun
+++++++++++

In EOImode=0, Priority Drop and Deactivate are undissociable. The
(simplified) interrupt handling flow is as follows: 

  <~IRQ>
    Acknowledge
    Priority Drop + Deactivate
    <interrupts can once again be signaled, once interrupts are re-enabled>

With EOImode=1, we can invoke each operation individually. This gives us:

  <~IRQ>
    Acknowledge
    Priority Drop
    <*other* interrupts can be signaled from here, once interrupts are re-enabled>
    Deactivate
    <*this* interrupt can be signaled again>

What this means is that with EOImode=1, any interrupt is kept "masked" by
its active bit between Priority Drop and Deactivate.

Threaded IRQs and ONESHOT
=========================

ONESHOT threaded IRQs must remain masked between the main handler and the
threaded handler. Right now we do this using the conventional irq_mask()
operations, which looks like this: 

 <irq handler>
   Acknowledge
   Priority Drop   
   irq_mask()
   Deactivate

 <threaded handler>
   irq_unmask()

However, masking for the GICs means poking the distributor, and there's no
sysreg for that - it's an MMIO access. We've seen above that our IRQ
handling can give us masking "for free", and this is what this patch set is
all about. It turns the above handling into:

  <irq handler>
    Acknowledge
    Priority Drop

  <threaded handler>
    Deactivate

No irq_mask() => fewer MMIO accesses => happier users (or so I've been
told). This is especially relevant to PREEMPT_RT which forces threaded
IRQs.
    
Testing
=======

GICv2
+++++

I've tested this on my Juno with forced irqthreads. This makes the pl011
IRQ into a threaded ONESHOT IRQ, so I spammed my keyboard into the console
and verified via ftrace that there were no irq_mask() / irq_unmask()
involved.

GICv3
+++++

I've tested this on my Ampere eMAG, which uncovered "fun" interactions with
the MSI domains. Did the same trick as the Juno with the pl011.

pNMIs cause said eMAG to freeze, but that's true even without my patches. I
did try them out under QEMU+KVM and that looked fine, although that means I
only got to test EOImode=0. I'll try to dig into this when I get some more
cycles.

TODOs
=====

MSI hierarchy story
+++++++++++++++++++

I 'hate' patch 8/10 because it's so very easy to break. See changelog for
my thoughts on the thing.

Performance numbers
+++++++++++++++++++

The whole point of this was to shave off some time spent issuing requests
to the distributor. On my Juno the IRQ for eth0 gets forcefully threaded
and thus becomes a ONESHOT threaded IRQ - I've tried to test this with
netperf, but the delta is lost in the noise (and there is quite a lot of
noise, unfortunately).

I'm still looking for something I can benchmark on the eMAG to get some
GICv3 results.

Links
=====

[1]: https://lore.kernel.org/lkml/1414235215-10468-1-git-send-email-marc.zyngier@arm.com/

Valentin Schneider (10):
  genirq: Add chip flag to denote automatic IRQ (un)masking
  genirq: Define irq_ack() and irq_eoi() helpers
  genirq: Employ ack_irq() and eoi_irq() where relevant
  genirq: Add handle_strict_flow_irq() flow handler
  genirq: Let purely flow-masked ONESHOT irqs through
    unmask_threaded_irq()
  genirq: Don't mask IRQ within flow handler if IRQ is flow-masked
  genirq, irq-gic-v3: Make NMI flow handlers use ->irq_ack() if
    available
  irqchip/gic-v3-its: Use irq_chip_ack_parent()
  irqchip/gic: Convert to handle_strict_flow_irq()
  irqchip/gic-v3: Convert to handle_strict_flow_irq()

 drivers/irqchip/irq-gic-v3-its-pci-msi.c |   1 +
 drivers/irqchip/irq-gic-v3-its.c         |   1 +
 drivers/irqchip/irq-gic-v3.c             |  27 ++++--
 drivers/irqchip/irq-gic.c                |  14 ++-
 include/linux/irq.h                      |  15 ++-
 kernel/irq/chip.c                        | 117 +++++++++++++++++++----
 kernel/irq/debugfs.c                     |   2 +
 kernel/irq/internals.h                   |   7 ++
 kernel/irq/manage.c                      |   2 +-
 9 files changed, 154 insertions(+), 32 deletions(-)

--
2.25.1