[PATCH net-next v4 2/6] net: dsa: mt7530: Extend device data ready for adding a new hardware
Landen Chao
landen.chao at mediatek.com
Fri Sep 11 08:56:24 EDT 2020
Add a structure holding required operations for each device such as device
initialization, PHY port read or write, a checker whether PHY interface is
supported on a certain port, MAC port setup for either bus pad or a
specific PHY interface.
The patch is done for ready adding a new hardware MT7531, and keep the
same setup logic of existing hardware.
Signed-off-by: Landen Chao <landen.chao at mediatek.com>
Signed-off-by: Sean Wang <sean.wang at mediatek.com>
---
drivers/net/dsa/mt7530.c | 271 ++++++++++++++++++++++++++++-----------
drivers/net/dsa/mt7530.h | 37 +++++-
2 files changed, 234 insertions(+), 74 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 238417db26f9..9c6f80b3e5f5 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -372,8 +372,9 @@ mt7530_fdb_write(struct mt7530_priv *priv, u16 vid,
mt7530_write(priv, MT7530_ATA1 + (i * 4), reg[i]);
}
+/* Setup TX circuit including relevant PAD and driving */
static int
-mt7530_pad_clk_setup(struct dsa_switch *ds, int mode)
+mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
{
struct mt7530_priv *priv = ds->priv;
u32 ncpo1, ssc_delta, trgint, i, xtal;
@@ -387,7 +388,7 @@ mt7530_pad_clk_setup(struct dsa_switch *ds, int mode)
return -EINVAL;
}
- switch (mode) {
+ switch (interface) {
case PHY_INTERFACE_MODE_RGMII:
trgint = 0;
/* PLL frequency: 125MHz */
@@ -409,7 +410,8 @@ mt7530_pad_clk_setup(struct dsa_switch *ds, int mode)
}
break;
default:
- dev_err(priv->dev, "xMII mode %d not supported\n", mode);
+ dev_err(priv->dev, "xMII interface %d not supported\n",
+ interface);
return -EINVAL;
}
@@ -1349,47 +1351,116 @@ mt7530_setup(struct dsa_switch *ds)
return 0;
}
-static void mt7530_phylink_mac_config(struct dsa_switch *ds, int port,
- unsigned int mode,
- const struct phylink_link_state *state)
+static bool
+mt7530_phy_mode_supported(struct dsa_switch *ds, int port,
+ const struct phylink_link_state *state)
{
struct mt7530_priv *priv = ds->priv;
- u32 mcr_cur, mcr_new;
switch (port) {
- case 0: /* Internal phy */
- case 1:
- case 2:
- case 3:
- case 4:
+ case 0 ... 4: /* Internal phy */
if (state->interface != PHY_INTERFACE_MODE_GMII)
- return;
+ return false;
break;
case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
- if (priv->p5_interface == state->interface)
- break;
if (!phy_interface_mode_is_rgmii(state->interface) &&
state->interface != PHY_INTERFACE_MODE_MII &&
state->interface != PHY_INTERFACE_MODE_GMII)
- return;
+ return false;
+ break;
+ case 6: /* 1st cpu port */
+ if (state->interface != PHY_INTERFACE_MODE_RGMII &&
+ state->interface != PHY_INTERFACE_MODE_TRGMII)
+ return false;
+ break;
+ default:
+ dev_err(priv->dev, "%s: unsupported port: %i\n", __func__,
+ port);
+ return false;
+ }
+
+ return true;
+}
+
+static bool
+mt753x_phy_mode_supported(struct dsa_switch *ds, int port,
+ const struct phylink_link_state *state)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ return priv->info->phy_mode_supported(ds, port, state);
+}
+
+static int
+mt753x_pad_setup(struct dsa_switch *ds, const struct phylink_link_state *state)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ return priv->info->pad_setup(ds, state->interface);
+}
+
+static int
+mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
+ phy_interface_t interface)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ /* Only need to setup port5. */
+ if (port != 5)
+ return 0;
+
+ mt7530_setup_port5(priv->ds, interface);
+
+ return 0;
+}
+
+static int
+mt753x_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ return priv->info->mac_port_config(ds, port, mode, state->interface);
+}
+
+static void
+mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
+ const struct phylink_link_state *state)
+{
+ struct mt7530_priv *priv = ds->priv;
+ u32 mcr_cur, mcr_new;
+
+ if (!mt753x_phy_mode_supported(ds, port, state))
+ goto unsupported;
+
+ switch (port) {
+ case 0 ... 4: /* Internal phy */
+ if (state->interface != PHY_INTERFACE_MODE_GMII)
+ goto unsupported;
+ break;
+ case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
+ if (priv->p5_interface == state->interface)
+ break;
+
+ if (mt753x_mac_config(ds, port, mode, state) < 0)
+ goto unsupported;
- mt7530_setup_port5(ds, state->interface);
break;
case 6: /* 1st cpu port */
if (priv->p6_interface == state->interface)
break;
- if (state->interface != PHY_INTERFACE_MODE_RGMII &&
- state->interface != PHY_INTERFACE_MODE_TRGMII)
- return;
+ mt753x_pad_setup(ds, state);
- /* Setup TX circuit incluing relevant PAD and driving */
- mt7530_pad_clk_setup(ds, state->interface);
+ if (mt753x_mac_config(ds, port, mode, state) < 0)
+ goto unsupported;
priv->p6_interface = state->interface;
break;
default:
- dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
+unsupported:
+ dev_err(ds->dev, "%s: unsupported %s port: %i\n",
+ __func__, phy_modes(state->interface), port);
return;
}
@@ -1453,61 +1524,44 @@ static void mt7530_phylink_mac_link_up(struct dsa_switch *ds, int port,
mt7530_set(priv, MT7530_PMCR_P(port), mcr);
}
-static void mt7530_phylink_validate(struct dsa_switch *ds, int port,
- unsigned long *supported,
- struct phylink_link_state *state)
+static void
+mt7530_mac_port_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported)
+{
+ if (port == 5)
+ phylink_set(supported, 1000baseX_Full);
+}
+
+static void
+mt753x_phylink_validate(struct dsa_switch *ds, int port,
+ unsigned long *supported,
+ struct phylink_link_state *state)
{
__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
+ struct mt7530_priv *priv = ds->priv;
- switch (port) {
- case 0: /* Internal phy */
- case 1:
- case 2:
- case 3:
- case 4:
- if (state->interface != PHY_INTERFACE_MODE_NA &&
- state->interface != PHY_INTERFACE_MODE_GMII)
- goto unsupported;
- break;
- case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
- if (state->interface != PHY_INTERFACE_MODE_NA &&
- !phy_interface_mode_is_rgmii(state->interface) &&
- state->interface != PHY_INTERFACE_MODE_MII &&
- state->interface != PHY_INTERFACE_MODE_GMII)
- goto unsupported;
- break;
- case 6: /* 1st cpu port */
- if (state->interface != PHY_INTERFACE_MODE_NA &&
- state->interface != PHY_INTERFACE_MODE_RGMII &&
- state->interface != PHY_INTERFACE_MODE_TRGMII)
- goto unsupported;
- break;
- default:
- dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port);
-unsupported:
+ if (state->interface != PHY_INTERFACE_MODE_NA &&
+ !mt753x_phy_mode_supported(ds, port, state)) {
linkmode_zero(supported);
return;
}
phylink_set_port_modes(mask);
- phylink_set(mask, Autoneg);
- if (state->interface == PHY_INTERFACE_MODE_TRGMII) {
- phylink_set(mask, 1000baseT_Full);
- } else {
+ if (state->interface != PHY_INTERFACE_MODE_TRGMII) {
phylink_set(mask, 10baseT_Half);
phylink_set(mask, 10baseT_Full);
phylink_set(mask, 100baseT_Half);
phylink_set(mask, 100baseT_Full);
-
- if (state->interface != PHY_INTERFACE_MODE_MII) {
- /* This switch only supports 1G full-duplex. */
- phylink_set(mask, 1000baseT_Full);
- if (port == 5)
- phylink_set(mask, 1000baseX_Full);
- }
+ phylink_set(mask, Autoneg);
}
+ /* This switch only supports 1G full-duplex. */
+ if (state->interface != PHY_INTERFACE_MODE_MII)
+ phylink_set(mask, 1000baseT_Full);
+
+ priv->info->mac_port_validate(ds, port, mask);
+
phylink_set(mask, Pause);
phylink_set(mask, Asym_Pause);
@@ -1555,12 +1609,45 @@ mt7530_phylink_mac_link_state(struct dsa_switch *ds, int port,
return 1;
}
+static int
+mt753x_phylink_mac_link_state(struct dsa_switch *ds, int port,
+ struct phylink_link_state *state)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ return priv->info->mac_port_get_state(ds, port, state);
+}
+
+static int
+mt753x_setup(struct dsa_switch *ds)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ return priv->info->sw_setup(ds);
+}
+
+static int
+mt753x_phy_read(struct dsa_switch *ds, int port, int regnum)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ return priv->info->phy_read(ds, port, regnum);
+}
+
+static int
+mt753x_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ return priv->info->phy_write(ds, port, regnum, val);
+}
+
static const struct dsa_switch_ops mt7530_switch_ops = {
.get_tag_protocol = mtk_get_tag_protocol,
- .setup = mt7530_setup,
+ .setup = mt753x_setup,
.get_strings = mt7530_get_strings,
- .phy_read = mt7530_phy_read,
- .phy_write = mt7530_phy_write,
+ .phy_read = mt753x_phy_read,
+ .phy_write = mt753x_phy_write,
.get_ethtool_stats = mt7530_get_ethtool_stats,
.get_sset_count = mt7530_get_sset_count,
.port_enable = mt7530_port_enable,
@@ -1577,16 +1664,41 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
.port_vlan_del = mt7530_port_vlan_del,
.port_mirror_add = mt7530_port_mirror_add,
.port_mirror_del = mt7530_port_mirror_del,
- .phylink_validate = mt7530_phylink_validate,
- .phylink_mac_link_state = mt7530_phylink_mac_link_state,
- .phylink_mac_config = mt7530_phylink_mac_config,
+ .phylink_validate = mt753x_phylink_validate,
+ .phylink_mac_link_state = mt753x_phylink_mac_link_state,
+ .phylink_mac_config = mt753x_phylink_mac_config,
.phylink_mac_link_down = mt7530_phylink_mac_link_down,
.phylink_mac_link_up = mt7530_phylink_mac_link_up,
};
+static const struct mt753x_info mt753x_table[] = {
+ [ID_MT7621] = {
+ .id = ID_MT7621,
+ .sw_setup = mt7530_setup,
+ .phy_read = mt7530_phy_read,
+ .phy_write = mt7530_phy_write,
+ .pad_setup = mt7530_pad_clk_setup,
+ .phy_mode_supported = mt7530_phy_mode_supported,
+ .mac_port_validate = mt7530_mac_port_validate,
+ .mac_port_get_state = mt7530_phylink_mac_link_state,
+ .mac_port_config = mt7530_mac_config,
+ },
+ [ID_MT7530] = {
+ .id = ID_MT7530,
+ .sw_setup = mt7530_setup,
+ .phy_read = mt7530_phy_read,
+ .phy_write = mt7530_phy_write,
+ .pad_setup = mt7530_pad_clk_setup,
+ .phy_mode_supported = mt7530_phy_mode_supported,
+ .mac_port_validate = mt7530_mac_port_validate,
+ .mac_port_get_state = mt7530_phylink_mac_link_state,
+ .mac_port_config = mt7530_mac_config,
+ },
+};
+
static const struct of_device_id mt7530_of_match[] = {
- { .compatible = "mediatek,mt7621", .data = (void *)ID_MT7621, },
- { .compatible = "mediatek,mt7530", .data = (void *)ID_MT7530, },
+ { .compatible = "mediatek,mt7621", .data = &mt753x_table[ID_MT7621], },
+ { .compatible = "mediatek,mt7530", .data = &mt753x_table[ID_MT7530], },
{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, mt7530_of_match);
@@ -1627,8 +1739,21 @@ mt7530_probe(struct mdio_device *mdiodev)
/* Get the hardware identifier from the devicetree node.
* We will need it for some of the clock and regulator setup.
*/
- priv->id = (unsigned int)(unsigned long)
- of_device_get_match_data(&mdiodev->dev);
+ priv->info = of_device_get_match_data(&mdiodev->dev);
+ if (!priv->info)
+ return -EINVAL;
+
+ /* Sanity check if these required device operations are filled
+ * properly.
+ */
+ if (!priv->info->sw_setup || !priv->info->pad_setup ||
+ !priv->info->phy_read || !priv->info->phy_write ||
+ !priv->info->phy_mode_supported ||
+ !priv->info->mac_port_validate ||
+ !priv->info->mac_port_get_state || !priv->info->mac_port_config)
+ return -EINVAL;
+
+ priv->id = priv->info->id;
if (priv->id == ID_MT7530) {
priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core");
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index 14de60d0b9ca..44ac55433089 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -11,7 +11,7 @@
#define MT7530_NUM_FDB_RECORDS 2048
#define MT7530_ALL_MEMBERS 0xff
-enum {
+enum mt753x_id {
ID_MT7530 = 0,
ID_MT7621 = 1,
};
@@ -443,6 +443,40 @@ static const char *p5_intf_modes(unsigned int p5_interface)
}
}
+/* struct mt753x_info - This is the main data structure for holding the specific
+ * part for each supported device
+ * @sw_setup: Holding the handler to a device initialization
+ * @phy_read: Holding the way reading PHY port
+ * @phy_write: Holding the way writing PHY port
+ * @pad_setup: Holding the way setting up the bus pad for a certain
+ * MAC port
+ * @phy_mode_supported: Check if the PHY type is being supported on a certain
+ * port
+ * @mac_port_validate: Holding the way to set addition validate type for a
+ * certan MAC port
+ * @mac_port_get_state: Holding the way getting the MAC/PCS state for a certain
+ * MAC port
+ * @mac_port_config: Holding the way setting up the PHY attribute to a
+ * certain MAC port
+ */
+struct mt753x_info {
+ enum mt753x_id id;
+
+ int (*sw_setup)(struct dsa_switch *ds);
+ int (*phy_read)(struct dsa_switch *ds, int port, int regnum);
+ int (*phy_write)(struct dsa_switch *ds, int port, int regnum, u16 val);
+ int (*pad_setup)(struct dsa_switch *ds, phy_interface_t interface);
+ bool (*phy_mode_supported)(struct dsa_switch *ds, int port,
+ const struct phylink_link_state *state);
+ void (*mac_port_validate)(struct dsa_switch *ds, int port,
+ unsigned long *supported);
+ int (*mac_port_get_state)(struct dsa_switch *ds, int port,
+ struct phylink_link_state *state);
+ int (*mac_port_config)(struct dsa_switch *ds, int port,
+ unsigned int mode,
+ phy_interface_t interface);
+};
+
/* struct mt7530_priv - This is the main data structure for holding the state
* of the driver
* @dev: The device pointer
@@ -468,6 +502,7 @@ struct mt7530_priv {
struct regulator *core_pwr;
struct regulator *io_pwr;
struct gpio_desc *reset;
+ const struct mt753x_info *info;
unsigned int id;
bool mcm;
phy_interface_t p6_interface;
--
2.17.1
More information about the linux-arm-kernel
mailing list