[PATCH 2/3] mmc: sdhci-of-aspeed: Expose data sample phase delay tuning
Joel Stanley
joel at jms.id.au
Thu Sep 10 22:02:58 EDT 2020
On Thu, 10 Sep 2020 at 10:55, Andrew Jeffery <andrew at aj.id.au> wrote:
>
> Allow sample phase adjustment to deal with layout or tolerance issues.
>
> Signed-off-by: Andrew Jeffery <andrew at aj.id.au>
> ---
> drivers/mmc/host/sdhci-of-aspeed.c | 137 +++++++++++++++++++++++++++--
> 1 file changed, 132 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-of-aspeed.c b/drivers/mmc/host/sdhci-of-aspeed.c
> index 4f008ba3280e..641accbfcde4 100644
> --- a/drivers/mmc/host/sdhci-of-aspeed.c
> +++ b/drivers/mmc/host/sdhci-of-aspeed.c
> @@ -16,9 +16,18 @@
>
> #include "sdhci-pltfm.h"
>
> -#define ASPEED_SDC_INFO 0x00
> -#define ASPEED_SDC_S1MMC8 BIT(25)
> -#define ASPEED_SDC_S0MMC8 BIT(24)
> +#define ASPEED_SDC_INFO 0x00
> +#define ASPEED_SDC_S1_MMC8 BIT(25)
> +#define ASPEED_SDC_S0_MMC8 BIT(24)
> +#define ASPEED_SDC_PHASE 0xf4
> +#define ASPEED_SDC_S1_PHASE_IN GENMASK(25, 21)
> +#define ASPEED_SDC_S0_PHASE_IN GENMASK(20, 16)
> +#define ASPEED_SDC_S1_PHASE_OUT GENMASK(15, 11)
> +#define ASPEED_SDC_S1_PHASE_IN_EN BIT(10)
> +#define ASPEED_SDC_S1_PHASE_OUT_EN GENMASK(9, 8)
> +#define ASPEED_SDC_S0_PHASE_OUT GENMASK(7, 3)
> +#define ASPEED_SDC_S0_PHASE_IN_EN BIT(2)
> +#define ASPEED_SDC_S0_PHASE_OUT_EN GENMASK(1, 0)
>
> struct aspeed_sdc {
> struct clk *clk;
> @@ -28,9 +37,21 @@ struct aspeed_sdc {
> void __iomem *regs;
> };
>
> +struct aspeed_sdhci_phase_desc {
> + u32 value_mask;
> + u32 enable_mask;
> + u8 enable_value;
> +};
> +
> +struct aspeed_sdhci_phase {
> + struct aspeed_sdhci_phase_desc in;
> + struct aspeed_sdhci_phase_desc out;
> +};
> +
> struct aspeed_sdhci {
> struct aspeed_sdc *parent;
> u32 width_mask;
> + const struct aspeed_sdhci_phase *phase;
> };
>
> static void aspeed_sdc_configure_8bit_mode(struct aspeed_sdc *sdc,
> @@ -50,6 +71,25 @@ static void aspeed_sdc_configure_8bit_mode(struct aspeed_sdc *sdc,
> spin_unlock(&sdc->lock);
> }
>
> +static void
> +aspeed_sdc_configure_phase(struct aspeed_sdc *sdc,
> + const struct aspeed_sdhci_phase_desc *phase,
> + uint8_t value, bool enable)
> +{
> + u32 reg;
> +
> + spin_lock(&sdc->lock);
What is the lock protecting against?
We call this in the ->probe, so there should be no concurrent access going on.
> + reg = readl(sdc->regs + ASPEED_SDC_PHASE);
> + reg &= ~phase->enable_mask;
> + if (enable) {
> + reg &= ~phase->value_mask;
> + reg |= value << __ffs(phase->value_mask);
> + reg |= phase->enable_value << __ffs(phase->enable_mask);
> + }
> + writel(reg, sdc->regs + ASPEED_SDC_PHASE);
> + spin_unlock(&sdc->lock);
> +}
> +
> static void aspeed_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
> {
> struct sdhci_pltfm_host *pltfm_host;
> @@ -155,8 +195,58 @@ static inline int aspeed_sdhci_calculate_slot(struct aspeed_sdhci *dev,
> return (delta / 0x100) - 1;
> }
>
> +static int aspeed_sdhci_configure_of(struct platform_device *pdev,
> + struct aspeed_sdhci *sdhci)
> +{
> + u32 iphase, ophase;
> + struct device_node *np;
> + struct device *dev;
> + int ret;
> +
> + if (!sdhci->phase)
> + return 0;
> +
> + dev = &pdev->dev;
> + np = dev->of_node;
> +
> + ret = of_property_read_u32(np, "aspeed,input-phase", &iphase);
> + if (ret < 0) {
> + aspeed_sdc_configure_phase(sdhci->parent, &sdhci->phase->in, 0,
> + false);
Will this clear any value that eg. u-boot writes?
The register should be left alone if the kernel doesn't have a
configuration of it's own, otherwise we may end up breaking an
otherwise working system.
> + dev_dbg(dev, "Input phase configuration disabled");
> + } else if (iphase >= (1 << 5)) {
> + dev_err(dev,
> + "Input phase value exceeds field range (5 bits): %u",
> + iphase);
> + return -ERANGE;
> + } else {
> + aspeed_sdc_configure_phase(sdhci->parent, &sdhci->phase->in,
> + iphase, true);
> + dev_info(dev, "Input phase relationship: %u", iphase);
Make theis _dbg, on a normal boot we don't need this chatter in the logs.
The same comments apply for the output.
> + }
> +
> + ret = of_property_read_u32(np, "aspeed,output-phase", &ophase);
> + if (ret < 0) {
> + aspeed_sdc_configure_phase(sdhci->parent, &sdhci->phase->out, 0,
> + false);
> + dev_dbg(dev, "Output phase configuration disabled");
> + } else if (ophase >= (1 << 5)) {
> + dev_err(dev,
> + "Output phase value exceeds field range (5 bits): %u",
> + iphase);
> + return -ERANGE;
This will cause the driver to fail to probe. I think skipping setting
of the phase is a better option.
> + } else {
> + aspeed_sdc_configure_phase(sdhci->parent, &sdhci->phase->out,
> + ophase, true);
> + dev_info(dev, "Output phase relationship: %u", ophase);
> + }
> +
> + return 0;
> +}
> +
> static int aspeed_sdhci_probe(struct platform_device *pdev)
> {
> + const struct aspeed_sdhci_phase *phase;
> struct sdhci_pltfm_host *pltfm_host;
> struct aspeed_sdhci *dev;
> struct sdhci_host *host;
> @@ -181,7 +271,10 @@ static int aspeed_sdhci_probe(struct platform_device *pdev)
> return -EINVAL;
>
> dev_info(&pdev->dev, "Configuring for slot %d\n", slot);
> - dev->width_mask = !slot ? ASPEED_SDC_S0MMC8 : ASPEED_SDC_S1MMC8;
> + dev->width_mask = !slot ? ASPEED_SDC_S0_MMC8 : ASPEED_SDC_S1_MMC8;
> + phase = of_device_get_match_data(&pdev->dev);
> + if (phase)
> + dev->phase = &phase[slot];
>
> sdhci_get_of_property(pdev);
>
> @@ -195,6 +288,10 @@ static int aspeed_sdhci_probe(struct platform_device *pdev)
> goto err_pltfm_free;
> }
>
> + ret = aspeed_sdhci_configure_of(pdev, dev);
> + if (ret)
> + goto err_sdhci_add;
> +
> ret = mmc_of_parse(host->mmc);
> if (ret)
> goto err_sdhci_add;
> @@ -230,10 +327,40 @@ static int aspeed_sdhci_remove(struct platform_device *pdev)
> return 0;
> }
>
> +static const struct aspeed_sdhci_phase ast2600_sdhci_phase[] = {
> + /* SDHCI/Slot 0 */
> + [0] = {
> + .in = {
> + .value_mask = ASPEED_SDC_S0_PHASE_IN,
> + .enable_mask = ASPEED_SDC_S0_PHASE_IN_EN,
> + .enable_value = 1,
> + },
> + .out = {
> + .value_mask = ASPEED_SDC_S0_PHASE_OUT,
> + .enable_mask = ASPEED_SDC_S0_PHASE_OUT_EN,
> + .enable_value = 3,
> + },
> + },
> + /* SDHCI/Slot 1 */
> + [1] = {
> + .in = {
> + .value_mask = ASPEED_SDC_S1_PHASE_IN,
> + .enable_mask = ASPEED_SDC_S1_PHASE_IN_EN,
> + .enable_value = 1,
> + },
> + .out = {
> + .value_mask = ASPEED_SDC_S1_PHASE_OUT,
> + .enable_mask = ASPEED_SDC_S1_PHASE_OUT_EN,
Is there any value in splitting the input and output phase values
up? (instead of taking the property from the device tree and putting
it in the hardware).
> + .enable_value = 3,
> + },
> + },
> +};
> +
> +/* If supported, phase adjustment fields are stored in the data pointer */
> static const struct of_device_id aspeed_sdhci_of_match[] = {
> { .compatible = "aspeed,ast2400-sdhci", },
> { .compatible = "aspeed,ast2500-sdhci", },
> - { .compatible = "aspeed,ast2600-sdhci", },
> + { .compatible = "aspeed,ast2600-sdhci", .data = ast2600_sdhci_phase },
> { }
> };
>
> --
> 2.25.1
>
More information about the linux-arm-kernel
mailing list