[PATCH v13 4/5] dt-bindings: remoteproc: Add documentation for ZynqMP R5 rproc bindings

Stefano Stabellini sstabellini at kernel.org
Thu Sep 10 20:32:02 EDT 2020


On Fri, 4 Sep 2020, Ben Levinsky wrote:
> Add binding for ZynqMP R5 OpenAMP.
> 
> Represent the RPU domain resources in one device node. Each RPU
> processor is a subnode of the top RPU domain node.
> 
> Signed-off-by: Jason Wu <j.wu at xilinx.com>
> Signed-off-by: Wendy Liang <jliang at xilinx.com>
> Signed-off-by: Michal Simek <michal.simek at xilinx.com>
> 
> Signed-off-by: Ben Levinsky <ben.levinsky at xilinx.com>
> ---
> v3:
> - update zynqmp_r5 yaml parsing to not raise warnings for extra
>   information in children of R5 node. The warning "node has a unit
>   name, but no reg or ranges property" will still be raised though 
>   as this particular node is needed to describe the
>   '#address-cells' and '#size-cells' information.
> v4::
> - remove warning '/example-0/rpu at ff9a0000/r5 at 0: 
>   node has a unit name, but no reg or ranges property'
>   by adding reg to r5 node.
> v5:
> - update device tree sample and yaml parsing to not raise any warnings
> - description for memory-region in yaml parsing
> - compatible string in yaml parsing for TCM
> v6:
> - remove coupling TCM nodes with remoteproc 
> - remove mailbox as it is optional not needed
> v7:
> - change lockstep-mode to xlnx,cluster-mode
> v9:
> - show example IPC nodes and tcm bank nodes
> v11:
> - add property meta-memory-regions to illustrate link
>   between r5 and TCM banks
> - update so no warnings from 'make dt_binding_check'
> ---
>  .../xilinx,zynqmp-r5-remoteproc.yaml          | 123 ++++++++++++++++++
>  1 file changed, 123 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/remoteproc/xilinx,zynqmp-r5-remoteproc.yaml
> 
> diff --git a/Documentation/devicetree/bindings/remoteproc/xilinx,zynqmp-r5-remoteproc.yaml b/Documentation/devicetree/bindings/remoteproc/xilinx,zynqmp-r5-remoteproc.yaml
> new file mode 100644
> index 000000000000..148374c61908
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/remoteproc/xilinx,zynqmp-r5-remoteproc.yaml
> @@ -0,0 +1,123 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/remoteproc/xilinx,zynqmp-r5-remoteproc.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Xilinx R5 remote processor controller bindings
> +
> +description:
> +  This document defines the binding for the remoteproc component that loads and
> +  boots firmwares on the Xilinx Zynqmp and Versal family chipset.
> +
> +  Note that the Linux has global addressing view of the R5-related memory (TCM)
> +  so the absolute address ranges are provided in TCM reg's.
> +maintainers:
> +  - Ed Mooring <ed.mooring at xilinx.com>
> +  - Ben Levinsky <ben.levinsky at xilinx.com>
> +
> +properties:
> +  compatible:
> +    const: "xlnx,zynqmp-r5-remoteproc-1.0"
> +
> +  lockstep-mode:
> +    description:
> +      R5 core configuration (split is 0 or lock-step and 1)
> +    maxItems: 1
> +
> +  interrupts:
> +    description:
> +      Interrupt mapping for remoteproc IPI. It is required if the
> +      user uses the remoteproc driver with the RPMsg kernel driver.
> +    maxItems: 6
> +
> +  memory-region:
> +    description:
> +      collection of memory carveouts used for elf-loading and inter-processor
> +      communication.
> +    maxItems: 4
> +    minItems: 4
> +  meta-memory-regions:
> +    description:
> +      collection of memories that are not present in the top level memory
> +      nodes' mapping. For example, R5s' TCM banks. These banks are needed
> +      for R5 firmware meta data such as the R5 firmware's heap and stack
> +  pnode-id:
> +    maxItems: 1
> +  mboxes:
> +    maxItems: 2
> +  mbox-names:
> +    maxItems: 2
> +
> +examples:
> +  - |
> +     reserved-memory {
> +          #address-cells = <1>;
> +          #size-cells = <1>;
> +          ranges;
> +          elf_load: rproc at 3ed000000 {
> +               no-map;
> +               reg = <0x3ed00000 0x40000>;
> +          };
> +     };
> +     rpu {
> +          compatible = "xlnx,zynqmp-r5-remoteproc-1.0";
> +          #address-cells = <1>;
> +          #size-cells = <1>;
> +          ranges;
> +          lockstep-mode = <0>;
> +          r5_0 {
> +               ranges;
> +               #address-cells = <1>;
> +               #size-cells = <1>;
> +               memory-region = <&elf_load>;
> +               meta-memory-regions = <0x40 0x41>;
> +               pnode-id = <0x7>;

I can see you are expecting a link from this node to the tcm nodes in
the driver, but I can't find such a link in this example.


> +          };
> +     };
> +
> +     /*
> +      * Below nodes are required if using TCM to load R5 firmware
> +      * if not, then either do not provide nodes are label as disabled in
> +      * status property
> +      */
> +     tcm_0a at ffe00000 {
> +         reg = <0xffe00000 0x10000>;
> +         pnode-id = <0xf>;
> +         no-map;
> +         status = "okay";
> +         phandle = <0x40>;
> +         compatible = "xlnx,tcm";
> +     };
> +     tcm_1a at ffe20000 {
> +         reg = <0xffe20000 0x10000>;
> +         pnode-id = <0x10>;
> +         no-map;
> +         status = "okay";
> +         compatible = "xlnx,tcm";
> +         phandle = <0x41>;
> +     };
> +
> +     /*
> +      * Below nodes are required for IPC, as Xilinx Kernel
> +      * can potentially have other applications that use CMA
> +      * and conflict from hardware design. With that in mind,
> +      * explicitly state the address spaces for the IPC remoteproc
> +      * mechanisms.
> +      *
> +      * If IPC not required and only elf-loading then these are not needed.
> +      */
> +     rpu0vdev0vring0: rpu0vdev0vring0 at 3ed40000 {
> +         no-map;
> +         reg = <0x3ed40000 0x4000>;
> +     };
> +     rpu0vdev0vring1: rpu0vdev0vring1 at 3ed44000 {
> +         no-map;
> +         reg = <0x3ed44000 0x4000>;
> +     };
> +     rpu0vdev0buffer: rpu0vdev0buffer at 3ed48000 {
> +         no-map;
> +         reg = <0x3ed48000 0x100000>;
> +     };

Shouldn't they be under reserved-memory?



More information about the linux-arm-kernel mailing list