[PATCH v14 1/2] media: dt-bindings: media: i2c: Document OV02A10 bindings

[Dongchun Zhu]

Add YAML device tree binding for OV02A10 CMOS image sensor,
and the relevant MAINTAINERS entries.

Signed-off-by: Dongchun Zhu <dongchun.zhu at mediatek.com>
---
 .../bindings/media/i2c/ovti,ov02a10.yaml           | 161 +++++++++++++++++++++
 MAINTAINERS                                        |   7 +
 2 files changed, 168 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml

diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml
new file mode 100644
index 0000000..8c30505
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml
@@ -0,0 +1,161 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright (c) 2020 MediaTek Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV02A10 CMOS Sensor Device Tree Bindings
+
+maintainers:
+  - Dongchun Zhu <dongchun.zhu at mediatek.com>
+
+description: |-
+  The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel
+  image sensor, which is the latest production derived from Omnivision's CMOS
+  image sensor technology. Ihis chip supports high frame rate speeds up to 30fps
+  @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The
+  sensor output is available via CSI-2 serial data output.
+
+properties:
+  compatible:
+    const: ovti,ov02a10
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    description:
+      External clock for the sensor.
+    items:
+      - const: eclk
+
+  clock-frequency:
+    description:
+      Frequency of the eclk clock in Hz.
+
+  dovdd-supply:
+    description:
+      Definition of the regulator used as Digital I/O voltage supply.
+
+  avdd-supply:
+    description:
+      Definition of the regulator used as Analog voltage supply.
+
+  dvdd-supply:
+    description:
+      Definition of the regulator used as Digital core voltage supply.
+
+  powerdown-gpios:
+    description:
+      Must be the device tree identifier of the GPIO connected to the
+      PD_PAD pin. This pin is used to place the OV02A10 into standby mode
+      or shutdown mode. As the line needs to be high for the powerdown mode
+      to be active, it should be marked GPIO_ACTIVE_HIGH.
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      Must be the device tree identifier of the GPIO connected to the
+      RST_PD pin. If specified, it will be asserted during driver probe.
+      As the line needs to be low for the reset to be active, it should be
+      marked GPIO_ACTIVE_LOW.
+    maxItems: 1
+
+  rotation:
+    description:
+      Definition of the sensor's placement.
+    allOf:
+      - $ref: "/schemas/types.yaml#/definitions/uint32"
+      - enum:
+          - 0    # Sensor Mounted Upright
+          - 180  # Sensor Mounted Upside Down
+        default: 0
+
+  ovti,mipi-clock-voltage:
+    description:
+      An array of 2-tuples items, and each item consists of link frequency and
+      MIPI clock voltage unit like <freq-kHz volt-unit>. Clock voltage unit is
+      dependent upon link speed, indicating MIPI transmission speed select that
+      controls D-PHY timing setting by adjusting MIPI clock voltage to improve
+      the clock driver capability.
+    $ref: "/schemas/types.yaml#/definitions/uint32-array"
+    minItems: 2
+    default: [390000, 4]
+
+  # See ../video-interfaces.txt for details
+  port:
+    type: object
+    additionalProperties: false
+    description:
+      Output port node, single endpoint describing the CSI-2 transmitter.
+
+    properties:
+      endpoint:
+        type: object
+        additionalProperties: false
+
+        properties:
+          link-frequencies: true
+          remote-endpoint: true
+
+        required:
+          - link-frequencies
+          - remote-endpoint
+
+    required:
+      - endpoint
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - clock-frequency
+  - dovdd-supply
+  - avdd-supply
+  - dvdd-supply
+  - powerdown-gpios
+  - reset-gpios
+  - port
+
+additionalProperties: false
+
+examples:
+  - |
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ov02a10: camera-sensor at 3d {
+            compatible = "ovti,ov02a10";
+            reg = <0x3d>;
+
+            powerdown-gpios = <&pio 107 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>;
+
+            clocks = <&ov02a10_clk>;
+            clock-names = "eclk";
+            clock-frequency = <24000000>;
+
+            rotation = <180>;
+            ovti,mipi-clock-voltage = <390000 4>;
+
+            dovdd-supply = <&ov02a10_dovdd>;
+            avdd-supply = <&ov02a10_avdd>;
+            dvdd-supply = <&ov02a10_dvdd>;
+
+            port {
+                wcam_out: endpoint {
+                    link-frequencies = /bits/ 64 <390000000>;
+                    remote-endpoint = <&mipi_in_wcam>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index deaafb6..48aa7a7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12718,6 +12718,13 @@ M:	Harald Welte <laforge at gnumonks.org>
 S:	Maintained
 F:	drivers/char/pcmcia/cm4040_cs.*
 
+OMNIVISION OV02A10 SENSOR DRIVER
+M:	Dongchun Zhu <dongchun.zhu at mediatek.com>
+L:	linux-media at vger.kernel.org
+S:	Maintained
+T:	git git://linuxtv.org/media_tree.git
+F:	Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml
+
 OMNIVISION OV13858 SENSOR DRIVER
 M:	Sakari Ailus <sakari.ailus at linux.intel.com>
 L:	linux-media at vger.kernel.org
-- 
2.9.2