[PATCH v4 62/78] drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate

[Maxime Ripard]

Hi Chanwoo,

On Tue, Sep 01, 2020 at 01:36:17PM +0900, Chanwoo Choi wrote:
> On 7/9/20 2:42 AM, Maxime Ripard wrote:
> > The HSM clock needs to be setup at around 101% of the pixel rate. This
> > was done previously by setting the clock rate to 163.7MHz at probe time and
> > only check in mode_valid whether the mode pixel clock was under the pixel
> > clock +1% or not.
> > 
> > However, with 4k we need to change that frequency to a higher frequency
> > than 163.7MHz, and yet want to have the lowest clock as possible to have a
> > decent power saving.
> > 
> > Let's change that logic a bit by setting the clock rate of the HSM clock
> > to the pixel rate at encoder_enable time. This would work for the
> > BCM2711 that support 4k resolutions and has a clock that can provide it,
> > but we still have to take care of a 4k panel plugged on a BCM283x SoCs
> > that wouldn't be able to use those modes, so let's define the limit in
> > the variant.
> > 
> > Signed-off-by: Maxime Ripard <maxime at cerno.tech>
> > ---
> >  drivers/gpu/drm/vc4/vc4_hdmi.c | 79 ++++++++++++++++-------------------
> >  drivers/gpu/drm/vc4/vc4_hdmi.h |  3 +-
> >  2 files changed, 41 insertions(+), 41 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
> > index 17797b14cde4..9f30fab744f2 100644
> > --- a/drivers/gpu/drm/vc4/vc4_hdmi.c
> > +++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
> > @@ -53,7 +53,6 @@
> >  #include "vc4_hdmi_regs.h"
> >  #include "vc4_regs.h"
> >  
> > -#define HSM_CLOCK_FREQ 163682864
> >  #define CEC_CLOCK_FREQ 40000
> >  
> >  static int vc4_hdmi_debugfs_regs(struct seq_file *m, void *unused)
> > @@ -326,6 +325,7 @@ static void vc4_hdmi_encoder_disable(struct drm_encoder *encoder)
> >  	HDMI_WRITE(HDMI_VID_CTL,
> >  		   HDMI_READ(HDMI_VID_CTL) & ~VC4_HD_VID_CTL_ENABLE);
> >  
> > +	clk_disable_unprepare(vc4_hdmi->hsm_clock);
> >  	clk_disable_unprepare(vc4_hdmi->pixel_clock);
> >  
> >  	ret = pm_runtime_put(&vc4_hdmi->pdev->dev);
> > @@ -423,6 +423,7 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
> >  	struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
> >  	struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
> >  	bool debug_dump_regs = false;
> > +	unsigned long pixel_rate, hsm_rate;
> >  	int ret;
> >  
> >  	ret = pm_runtime_get_sync(&vc4_hdmi->pdev->dev);
> > @@ -431,9 +432,8 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
> >  		return;
> >  	}
> >  
> > -	ret = clk_set_rate(vc4_hdmi->pixel_clock,
> > -			   mode->clock * 1000 *
> > -			   ((mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1));
> > +	pixel_rate = mode->clock * 1000 * ((mode->flags & DRM_MODE_FLAG_DBLCLK) ? 2 : 1);
> > +	ret = clk_set_rate(vc4_hdmi->pixel_clock, pixel_rate);
> >  	if (ret) {
> >  		DRM_ERROR("Failed to set pixel clock rate: %d\n", ret);
> >  		return;
> > @@ -445,6 +445,36 @@ static void vc4_hdmi_encoder_enable(struct drm_encoder *encoder)
> >  		return;
> >  	}
> >  
> > +	/*
> > +	 * As stated in RPi's vc4 firmware "HDMI state machine (HSM) clock must
> > +	 * be faster than pixel clock, infinitesimally faster, tested in
> > +	 * simulation. Otherwise, exact value is unimportant for HDMI
> > +	 * operation." This conflicts with bcm2835's vc4 documentation, which
> > +	 * states HSM's clock has to be at least 108% of the pixel clock.
> > +	 *
> > +	 * Real life tests reveal that vc4's firmware statement holds up, and
> > +	 * users are able to use pixel clocks closer to HSM's, namely for
> > +	 * 1920x1200 at 60Hz. So it was decided to have leave a 1% margin between
> > +	 * both clocks. Which, for RPi0-3 implies a maximum pixel clock of
> > +	 * 162MHz.
> > +	 *
> > +	 * Additionally, the AXI clock needs to be at least 25% of
> > +	 * pixel clock, but HSM ends up being the limiting factor.
> > +	 */
> > +	hsm_rate = max_t(unsigned long, 120000000, (pixel_rate / 100) * 101);
> > +	ret = clk_set_rate(vc4_hdmi->hsm_clock, hsm_rate);
> > +	if (ret) {
> > +		DRM_ERROR("Failed to set HSM clock rate: %d\n", ret);
> > +		return;
> > +	}
> > +
> > +	ret = clk_prepare_enable(vc4_hdmi->hsm_clock);
> > +	if (ret) {
> > +		DRM_ERROR("Failed to turn on HSM clock: %d\n", ret);
> > +		clk_disable_unprepare(vc4_hdmi->pixel_clock);
> > +		return;
> > +	}
> 
> About vc4_hdmi->hsm_clock instance, usually, we need to enable the clock
> with clk_prepare_enable() and then touch the clock like clk_set_rate().
> I think that need to enable the clock before calling clk_set_rate().
> 
> When I tested this patchset, it is well working because I think that
> vc4_hdmi->hsm_clock was already enabled on other side.

There's no clear rule here on the ordering (at least enforced by the
framework). There's clocks that need to be disabled to change their rate
(CLK_SET_RATE_GATE) and some that need to be enabled to change their
rate (CLK_SET_RATE_UNGATE).

Generally speaking, it seems more logical to me to have first the rate
changed and then the clock enabled since it won't create any "hiccup",
but I could very well see the opposite to be preferred.

Maxime
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20200901/83ec3517/attachment.sig>