[PATCH 11/13] ARM: dts: exynos: Silence SATA PHY warning in Exynos5250 Arndale

[Krzysztof Kozlowski]

On Tue, 1 Sep 2020 at 10:17, Krzysztof Kozlowski <krzk at kernel.org> wrote:
>
> On Tue, 1 Sep 2020 at 10:13, Marek Szyprowski <m.szyprowski at samsung.com> wrote:
> >
> > Hi Krzysztof,
> >
> > On 01.09.2020 09:54, Krzysztof Kozlowski wrote:
> > > The SATA PHY in Exynos5250 SoCs has two interfaces and two device nodes:
> > > 1. sata-phy at 12170000
> > > 2. i2c-9/i2c at 38
> > >
> > > The first node represents the actual SATA PHY device with phy-cells.
> > > The second represents additional I2C interface, needed by the driver
> > > to communicate with the SATA PHY device.  It is not a PHY-provider in
> > > the terms of dtschema so rename it to silence dtbs_check warning:
> > >
> > >    arch/arm/boot/dts/exynos5250-arndale.dt.yaml: sata-phy at 38: '#phy-cells' is a required property
> > >      From schema: lib/python3.6/site-packages/dtschema/schemas/phy/phy-provider.yaml
> > >
> > > Signed-off-by: Krzysztof Kozlowski <krzk at kernel.org>
> > > ---
> > >   arch/arm/boot/dts/exynos5250-arndale.dts | 2 +-
> > >   1 file changed, 1 insertion(+), 1 deletion(-)
> > >
> > > diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
> > > index f2bcce167b2d..3c401c82905c 100644
> > > --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> > > +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> > > @@ -544,7 +544,7 @@
> > >       samsung,i2c-max-bus-freq = <40000>;
> > >       samsung,i2c-slave-addr = <0x38>;
> > >
> > > -     sata_phy_i2c: sata-phy at 38 {
> > > +     sata_phy_i2c: sata-phy-i2c at 38 {
> > >               compatible = "samsung,exynos-sataphy-i2c";
> > >               reg = <0x38>;
> > >       };
> >
> > I'm not against the rename, but frankly, the above node and all i2c
> > parameters should be moved to exynos5250.dtsi. This is a SoC internal
> > things (the same way as hdmiphy in exynos4.dtsi), so the board dts
> > should only contain information like status = "enabled" for i2c_8 and
> > hdmi_i2c_phy nodes. No need to duplicate it here and in smdk5250.dts.
>
> Good point, the I2C bus used here is an internal part of SoC.
>
> I will squash these two changes into a new one. Thanks for the review!

While at it, I wonder about the samsung,i2c-slave-addr property. Is it
really needed? Are there multiple masters on this bus?

Best regards,
Krzysztof