[PATCH v3 2/2] ARM: dts: imx7: add support for kamstrup flex concentrator
Shawn Guo
shawnguo at kernel.org
Wed Oct 28 08:40:46 EDT 2020
On Wed, Sep 23, 2020 at 05:40:24PM +0200, Bruno Thomsen wrote:
> This adds support for the OMNIA Flex Concentrator product
> from Kamstrup A/S. It's providing radio mesh communication
> infrastructure for smart electricity meters.
>
> Kamstrup OMNIA is a modular and scalable smart grid platform.
>
> Signed-off-by: Bruno Thomsen <bruno.thomsen at gmail.com>
> ---
> Changes since version 2:
> - Found root cause of Ethernet PHY auto detect issue and created
> a mdio patch series that resolves the issue.
> https://lore.kernel.org/netdev/20200730195749.4922-1-bruno.thomsen@gmail.com/
> - Ethernet PHY reset is using new MDIO bus reset.
> - Ethernet PHY interrupt added.
> - Removed SION from a few GPIOs used for Ethernet PHY.
>
> Changes since version 1:
> - Sorted labeling nodes.
> - Sorted pinctrl entries.
> - Removed deprecated fec phy reset properties.
> - Added mdio phy reset properties.
> - Disabled phy type auto detection and added note to commit message.
> - Fixed two comment typos.
>
> arch/arm/boot/dts/Makefile | 2 +
> .../boot/dts/imx7d-flex-concentrator-mfg.dts | 25 ++
> arch/arm/boot/dts/imx7d-flex-concentrator.dts | 319 ++++++++++++++++++
> 3 files changed, 346 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts
> create mode 100644 arch/arm/boot/dts/imx7d-flex-concentrator.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 4572db3fa5ae..15be5a2fe831 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -634,6 +634,8 @@ dtb-$(CONFIG_SOC_IMX7D) += \
> imx7d-colibri-emmc-aster.dtb \
> imx7d-colibri-emmc-eval-v3.dtb \
> imx7d-colibri-eval-v3.dtb \
> + imx7d-flex-concentrator.dtb \
> + imx7d-flex-concentrator-mfg.dtb \
> imx7d-mba7.dtb \
> imx7d-meerkat96.dtb \
> imx7d-nitrogen7.dtb \
> diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts b/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts
> new file mode 100644
> index 000000000000..789f0837058f
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts
> @@ -0,0 +1,25 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree Source for Kamstrup OMNIA Flex Concentrator in
> + * manufacturing/debugging mode.
> + *
> + * Copyright (C) 2020 Kamstrup A/S
> + * Author: Bruno Thomsen <bruno.thomsen at gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "imx7d-flex-concentrator.dts"
> +
> +/ {
> + model = "Kamstrup OMNIA Flex Concentrator - Manufacturing";
> + compatible = "kam,imx7d-flex-concentrator-mfg", "kam,imx7d-flex-concentrator", "fsl,imx7d";
'make dtbs_check' reports the following issue:
compatible: ['kam,imx7d-flex-concentrator-mfg', 'kam,imx7d-flex-concentrator', 'fsl,imx7d'] is too long
I think dropping 'kam,imx7d-flex-concentrator' should fix it.
> +
> + chosen {
> + stdout-path = &uart4;
> + };
> +};
> +
> +&uart4 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator.dts b/arch/arm/boot/dts/imx7d-flex-concentrator.dts
> new file mode 100644
> index 000000000000..9f73c79253cb
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx7d-flex-concentrator.dts
> @@ -0,0 +1,319 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree Source for Kamstrup OMNIA Flex Concentrator.
> + *
> + * Copyright (C) 2020 Kamstrup A/S
> + * Author: Bruno Thomsen <bruno.thomsen at gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "imx7d-tqma7.dtsi"
> +
> +/* Some I2C devices on TQMa7 SoM are not mounted */
> +/delete-node/ &m24c64;
> +/delete-node/ &ds1339;
> +
> +/ {
> + model = "Kamstrup OMNIA Flex Concentrator";
> + compatible = "kam,imx7d-flex-concentrator", "fsl,imx7d";
> +
> + memory at 80000000 {
> + device_type = "memory";
> + /* 1024 MB - TQMa7D board configuration */
> + reg = <0x80000000 0x40000000>;
> + };
> +
> + reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "VBUS_USBOTG2";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_vref_1v8: regulator-vref-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC1V8_REF";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + vin-supply = <&sw2_reg>;
> + };
> +
> + /*
> + * Human Machine Interface consists of 4 dual red/green LEDs.
> + * hmi-a-green is controlled directly by the switch-mode power supply.
> + * hmi-a-red is not used.
> + */
> + gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_leds>;
> +
> + hmi-b-red {
gpio-leds: 'hmi-b-green', 'hmi-b-red', 'hmi-c-green', 'hmi-c-red', 'hmi-d-green', 'hmi-d-red' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/leds/leds-gpio.yaml
Shawn
> + label = "hmi-b:red:provisioning";
> + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + hmi-b-green {
> + label = "hmi-b:green:operation";
> + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + hmi-c-red {
> + label = "hmi-c:red:mesh-error";
> + gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + hmi-c-green {
> + label = "hmi-c:green:mesh-activity";
> + gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + hmi-d-red {
> + label = "hmi-d:red:wan-down";
> + gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + hmi-d-green {
> + label = "hmi-d:green:ipsec-up";
> + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> + };
> +
> + /*
> + * Errata e10574 board restart workaround.
> + */
> + gpio-restart {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_restart>;
> + compatible = "gpio-restart";
> + gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
> + priority = <200>;
> + };
> +};
> +
> +/*
> + * Analog signals
> + * ADC1_IN0: SMPS - 5V output monitor (voltage divider: 1/0.2806)
> + */
> +&adc1 {
> + vref-supply = <®_vref_1v8>;
> + status = "okay";
> +};
> +
> +&ecspi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + num-chipselects = <1>;
> + cs-gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +
> + pcf2127: rtc at 0 {
> + compatible = "nxp,pcf2127";
> + reg = <0>;
> + spi-max-frequency = <2000000>;
> + };
> +};
> +
> +&ecspi4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi4>;
> + num-chipselects = <1>;
> + cs-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +
> + /*
> + * ST chip maximum SPI clock frequency is 33 MHz.
> + *
> + * TCG specification - Section 6.4.1 Clocking:
> + * TPM shall support a SPI clock frequency range of 10-24 MHz.
> + */
> + st33htph: tpm-tis at 0 {
> + compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
> + reg = <0>;
> + spi-max-frequency = <24000000>;
> + };
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet1>;
> + phy-mode = "rmii";
> + phy-handle = <ðphy>;
> + status = "okay";
> +
> + /*
> + * MDIO bus reset is used to generate PHY device reset before
> + * Ethernet PHY type ID auto-detection. Otherwise this communication
> + * fails as device does not answer when recommended reset circuit
> + * is used.
> + */
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reset-delay-us = <100000>;
> + reset-post-delay-us = <500000>;
> + reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>;
> +
> + /* Microchip/Micrel KSZ8081RNB */
> + ethphy: ethernet-phy at 1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + interrupt-parent = <&gpio1>;
> + interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
> + reg = <1>;
> + };
> + };
> +};
> +
> +/*
> + * Detection signals for internal USB modules.
> + * Used for robust USB plug and play handling such as USB downstream port
> + * power-cycle and USB hub reset in case of misbehaving or crashed modules.
> + *
> + * SMPS - AC input monitor based on zero crossing.
> + * Used for last gasp notification.
> + */
> +&gpio3 {
> + gpio-line-names = "", "", "", "", "", "", "", "",
> + "", "", "", "", "smps-ac-monitor", "", "usb-hub-reset", "",
> + "", "", "", "", "", "", "", "",
> + "", "module-b-detection", "", "module-a-detection", "", "", "", "";
> +};
> +
> +/*
> + * Tamper IRQ trigger timestamp reading.
> + * Used for sealed cover opened/closed notification.
> + */
> +&gpio5 {
> + gpio-line-names = "", "", "", "", "", "", "", "",
> + "", "", "", "", "rtc-tamper-irq", "", "", "",
> + "", "", "", "", "", "", "", "",
> + "", "", "", "", "", "", "", "";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_misc>;
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX7D_PAD_ECSPI2_MISO__ECSPI2_MISO 0x7c /* X2-15 */
> + MX7D_PAD_ECSPI2_MOSI__ECSPI2_MOSI 0x74 /* X2-18 */
> + MX7D_PAD_ECSPI2_SCLK__ECSPI2_SCLK 0x74 /* X2-13 */
> + MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 0x74 /* X2-20 */
> + /* RTC - Tamper IRQ */
> + MX7D_PAD_SD2_CLK__GPIO5_IO12 0x3c /* X1-92 */
> + >;
> + };
> +
> + pinctrl_ecspi4: ecspi4grp {
> + fsl,pins = <
> + MX7D_PAD_LCD_CLK__ECSPI4_MISO 0x7c /* X2-72 */
> + MX7D_PAD_LCD_ENABLE__ECSPI4_MOSI 0x74 /* X2-68 */
> + MX7D_PAD_LCD_HSYNC__ECSPI4_SCLK 0x74 /* X2-76 */
> + MX7D_PAD_LCD_VSYNC__GPIO3_IO3 0x74 /* X2-78 */
> + >;
> + };
> +
> + pinctrl_enet1: enet1grp {
> + fsl,pins = <
> + MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x03 /* X2-48 */
> + MX7D_PAD_GPIO1_IO11__ENET1_MDC 0x03 /* X2-46 */
> + MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x71 /* X2-53 */
> + MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x71 /* X2-55 */
> + MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x71 /* X2-61 */
> + MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x79 /* X2-56 */
> + MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x79 /* X2-58 */
> + MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x79 /* X2-64 */
> + MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER 0x73 /* X2-52 */
> + /* PHY reset: SRE_FAST, DSE_X1 */
> + MX7D_PAD_ENET1_COL__GPIO7_IO15 0x00 /* X1-96 */
> + /* Clock from PHY to MAC: 100kPU */
> + MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 0x70 /* X3-4 */
> + /* PHY interrupt: 100kPU, HYS */
> + MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x78 /* X1-80 */
> + >;
> + };
> +
> + pinctrl_leds: ledsgrp {
> + fsl,pins = <
> + MX7D_PAD_LCD_DATA01__GPIO3_IO6 0x14 /* X2-82 */
> + MX7D_PAD_EPDC_BDR0__GPIO2_IO28 0x14 /* X1-82 */
> + MX7D_PAD_EPDC_BDR1__GPIO2_IO29 0x14 /* X1-84 */
> + MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 0x14 /* X1-86 */
> + MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 0x14 /* X1-88 */
> + MX7D_PAD_UART2_TX_DATA__GPIO4_IO3 0x14 /* X1-90 */
> + >;
> + };
> +
> + pinctrl_misc: miscgrp {
> + fsl,pins = <
> + /* Module A detection (low = present) */
> + MX7D_PAD_LCD_DATA22__GPIO3_IO27 0x7c /* X2-105 */
> + /* Module B detection (low = present) */
> + MX7D_PAD_LCD_DATA20__GPIO3_IO25 0x7c /* X2-103 */
> + /* SMPS - AC input monitor (high = failure) */
> + MX7D_PAD_LCD_DATA07__GPIO3_IO12 0x7c /* X2-88 */
> + /* USB - Hub reset */
> + MX7D_PAD_LCD_DATA09__GPIO3_IO14 0x74 /* X2-92 */
> + >;
> + };
> +
> + pinctrl_restart: restartgrp {
> + fsl,pins = <
> + MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12 0x74 /* X1-94 */
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX7D_PAD_SAI2_TX_SYNC__UART4_DCE_RX 0x7e /* X3-14 */
> + MX7D_PAD_SAI2_TX_BCLK__UART4_DCE_TX 0x76 /* X3-16 */
> + >;
> + };
> +};
> +
> +&iomuxc_lpsr {
> + pinctrl_usbotg2: usbotg2grp {
> + fsl,pins = <
> + MX7D_PAD_LPSR_GPIO1_IO06__USB_OTG2_OC 0x5c /* X3-11 */
> + MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7 0x59 /* X3-9 */
> + >;
> + };
> +
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + assigned-clocks = <&clks IMX7D_UART4_ROOT_SRC>;
> + assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
> +};
> +
> +&usbotg2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg2>;
> + vbus-supply = <®_usb_otg2_vbus>;
> + srp-disable;
> + hnp-disable;
> + adp-disable;
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +/*
> + * External watchdog feature provided by pcf2127.
> + */
> +&wdog1 {
> + status = "disabled";
> +};
> --
> 2.26.2
>
More information about the linux-arm-kernel
mailing list