[PATCH 01/18] dmaengine: of-dma: Add support for optional router configuration callback

[Vinod Koul]

On 08-10-20, 09:41, Peter Ujfalusi wrote:
> 
> 
> On 07/10/2020 18.55, Vinod Koul wrote:
> > On 07-10-20, 11:08, Peter Ujfalusi wrote:
> > 
> >> Not really. In DT an event triggered channel can be requested via router
> >> (when this is used) for example:
> >>
> >> dmas = <&inta_l2g a b c>;
> >> a - the input number of the DMA request in l2g
> >> b - edge or level trigger to be selected
> >> c - ASEL number for the channel for coherency
> >>
> >> The l2g router driver then translate this to:
> >> <&main_bcdma 1 0 c>
> >> 1 - Global trigger 0 is used by the DMA
> >> 0 - ignored
> >> c - ASEL number.
> >>
> >> The router needs to send an event which is going to be received by the
> >> channel we have picked up, this event number can only be known when we
> >> do have the channel.
> >>
> >> So the flow in this case:
> >> router converts the dma_spec for the DMA, but it does not yet know what
> >> is the event number it has to use.
> >> The BCDMA driver will pick an available bchan and notes that the
> >> transfers will be triggered by global event 0.
> >> When we have the channel, the core saves the router information and
> >> calls the device_router_config of BCDMA.
> >> In there we call back to the router and give the event number it has to
> >> use to send the trigger for the channel.
> > 
> > Ah that is intresting, so you would call router driver foo_set_event()
> > and would send the event number
> 
> Yes, that's correct.
> 
> > why not call that API from alloc
> > channel or even xlate?
> 
> at alloc / xlate time the DMA driver does not have information about
> router. The alloc/xlate will result the channel, but in my case it will
> result a broken setup as the router does not know which event to send.
> 
> > Why do you need new callback?
> 
> When I added the DMA event router support, it was designed in a way that
> the DMA driver itself must not know anything about the router, it has to
> be transparent. One can just add a router on front of any DMA and
> everything will work.
> This is the right thing to do, and it works for existing setups.
> 
> > Or did i miss something..
> 
> The BCDMA triggered channel setup is a chicken-egg setup.
> For this case the channel can be triggered by a global event. A channel
> can receive two global event, but this is not a concern atm.
> The event number depends on the channel we use, for simplicity let's
> say: bchan_id + trigger_offset = bchan_trigger_evt.
> 
> of_dma_router_xlate does this:
> 
> 1. calls the dma router's of_dma_route_allocate callback to allocate a
> route and craft a dma_spec for the DMA to configure a channel.
> 
> 2. using this crafted dma_spec we request a channel via of_dma_xlate
> callback
> 
> 3. if we got the channel, we save the router information, so it can be
> deallocated when the channel is disabled.
> 
> I need a fourth step to do a final configuration since only at this time
> (after it has been allocated) the channel has information about possible
> router.
> 
> In the new optional callback the DMA driver can figure out the event
> number which must be used by the router to send the event to the desired
> global event target of the channel.
> 
> Other DMAs might need something different, but imho if there is going to
> be a need for such post alloc router config, then it is most likely will
> come from the need to feed back some sort of channel information to the
> router. Or take parameter from the router itself for the channel.
> 
> To summarize:
> In of_dma_route_allocate() the router does not yet know the channel we
> are going to get.
> In of_dma_xlate() the DMA driver does not yet know if the channel will
> use router or not.
> I need to tell the router the event number it has to send, which is
> based on the channel number I got.

Sounds reasonable, btw why not pass this information in xlate. Router
will have a different xlate rather than non router right, or is it same.

If this information is anyway available in DT might be better to get it
and use from DT

Thanks

-- 
~Vinod