[RFC PATCH 0/4] ACPI/IORT: Support for IORT RMR node

Shameer Kolothum shameerali.kolothum.thodi at huawei.com
Tue Oct 27 07:26:42 EDT 2020


The series adds support to IORT RMR nodes specified in IORT
Revision E -ARM DEN 0049E[0]. RMR nodes are used to describe memory
ranges that are used by endpoints and require a unity mapping
in SMMU.

We have faced issues with 3408iMR RAID controller cards which
fail to boot when SMMU is enabled. This is because these controllers
make use of host memory for various caching related purposes and when
SMMU is enabled the iMR firmware fails to access these memory regions
as there is no mapping for them. IORT RMR provides a way for UEFI to
describe and report these memory regions so that the kernel can make
a unity mapping for these in SMMU.

RFC because, Patch #1 is to update the actbl2.h and should be done
through acpica update. I have send out a pull request[1] for that.

Tests:

With a UEFI, that reports the RMR for the dev,
....
[16F0h 5872   1]                         Type : 06
[16F1h 5873   2]                       Length : 007C
[16F3h 5875   1]                     Revision : 00
[1038h 0056   2]                     Reserved : 00000000
[1038h 0056   2]                   Identifier : 00000000
[16F8h 5880   4]                Mapping Count : 00000001
[16FCh 5884   4]               Mapping Offset : 00000040

[1700h 5888   4]    Number of RMR Descriptors : 00000002
[1704h 5892   4]        RMR Descriptor Offset : 00000018

[1708h 5896   8]          Base Address of RMR : 0000E6400000
[1710h 5904   8]                Length of RMR : 000000100000
[1718h 5912   4]                     Reserved : 00000000

[171Ch 5916   8]          Base Address of RMR : 0000000027B00000
[1724h 5924   8]                Length of RMR : 0000000000C00000
[172Ch 5932   4]                     Reserved : 00000000

[1730h 5936   4]                   Input base : 00000000
[1734h 5940   4]                     ID Count : 00000001
[1738h 5944   4]                  Output Base : 00000003
[173Ch 5948   4]             Output Reference : 00000064
[1740h 5952   4]        Flags (decoded below) : 00000001
                               Single Mapping : 1
...

Without the series the RAID controller initilization fails as
below,

...
[   12.631117] megaraid_sas 0000:03:00.0: FW supports sync cache        : Yes   
[   12.637360] megaraid_sas 0000:03:00.0: megasas_disable_intr_fusion is called outbound_intr_mask:0x40000009                                                   
[   18.776377] megaraid_sas 0000:03:00.0: Init cmd return status FAILED for SCSI host 0                                                                         
[   23.019383] megaraid_sas 0000:03:00.0: Waiting for FW to come to ready state 
[  106.684281] megaraid_sas 0000:03:00.0: FW in FAULT state, Fault code:0x10000 subcode:0x0 func:megasas_transition_to_ready                                    
[  106.695186] megaraid_sas 0000:03:00.0: System Register set:                  
[  106.889787] megaraid_sas 0000:03:00.0: Failed to transition controller to ready for scsi0.                                                                   
[  106.910475] megaraid_sas 0000:03:00.0: Failed from megasas_init_fw 6407      
estuary:/$

With the series, now the kernel has direct mapping for the dev as
below,

estuary:/$ cat /sys/kernel/iommu_groups/0/reserved_regions                      
0x0000000008000000 0x00000000080fffff msi                                       
0x0000000027b00000 0x00000000286fffff direct                                    
0x00000000e6400000 0x00000000e64fffff direct                                    
estuary:/$

....
[   12.254318] megaraid_sas 0000:03:00.0: megasas_disable_intr_fusion is called outbound_intr_mask:0x40000009                                                   
[   12.739089] megaraid_sas 0000:03:00.0: FW provided supportMaxExtLDs: 0      max_lds: 32                                                                      
[   12.746628] megaraid_sas 0000:03:00.0: controller type       : iMR(0MB)      
[   12.752694] megaraid_sas 0000:03:00.0: Online Controller Reset(OCR)  : Enabled                                                                               
[   12.759798] megaraid_sas 0000:03:00.0: Secure JBOD support   : Yes           
[   12.765778] megaraid_sas 0000:03:00.0: NVMe passthru support : Yes           
[   12.771931] megaraid_sas 0000:03:00.0: FW provided TM TaskAbort/Reset timeou: 6 secs/60 secs                                                                 
[   12.780503] megaraid_sas 0000:03:00.0: JBOD sequence map support     : Yes   
[   12.787000] megaraid_sas 0000:03:00.0: PCI Lane Margining support    : No    
[   12.819179] megaraid_sas 0000:03:00.0: NVME page size        : (4096)        
[   12.825672] megaraid_sas 0000:03:00.0: megasas_enable_intr_fusion is called outbound_intr_mask:0x40000000                                                    
[   12.835199] megaraid_sas 0000:03:00.0: INIT adapter done                     
[   12.873932] megaraid_sas 0000:03:00.0: pci id                : (0x1000)/(0x0017)/(0x19e5)/(0xd213)                                                           
[   12.881644] megaraid_sas 0000:03:00.0: unevenspan support    : no            
[   12.887451] megaraid_sas 0000:03:00.0: firmware crash dump   : no            
[   12.893344] megaraid_sas 0000:03:00.0: JBOD sequence map     : enabled       

RAID controller init is now success and can detect the drives
attached as well.

Thanks,
Shameer

[0]. https://developer.arm.com/documentation/den0049/latest/
[1]. https://github.com/acpica/acpica/pull/638

Shameer Kolothum (4):
  ACPICA: IORT: Update for revision E
  ACPI/IORT: Add support for RMR node parsing
  ACPI/IORT: Add RMR memory regions reservation helper
  iommu/dma: Reserve any RMR regions associated with a dev

 drivers/acpi/arm64/iort.c | 175 +++++++++++++++++++++++++++++++++++++-
 drivers/iommu/dma-iommu.c |  12 ++-
 include/acpi/actbl2.h     |  25 ++++--
 include/linux/acpi_iort.h |   4 +
 4 files changed, 205 insertions(+), 11 deletions(-)

-- 
2.17.1




More information about the linux-arm-kernel mailing list