[PATCH v15 1/2] media: dt-bindings: media: i2c: Document OV02A10 bindings
Sakari Ailus
sakari.ailus at linux.intel.com
Tue Oct 13 12:19:39 EDT 2020
Hi Dongchun,
On Tue, Oct 13, 2020 at 09:05:02PM +0800, Dongchun Zhu wrote:
> Add YAML device tree binding for OV02A10 CMOS image sensor, and the
> relevant MAINTAINERS entries.
>
> Signed-off-by: Dongchun Zhu <dongchun.zhu at mediatek.com>
> ---
> .../bindings/media/i2c/ovti,ov02a10.yaml | 162 +++++++++++++++++++++
> MAINTAINERS | 7 +
> 2 files changed, 169 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml
> new file mode 100644
> index 0000000..fb98964
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml
> @@ -0,0 +1,162 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright (c) 2020 MediaTek Inc.
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Omnivision OV02A10 CMOS Sensor Device Tree Bindings
> +
> +maintainers:
> + - Dongchun Zhu <dongchun.zhu at mediatek.com>
> +
> +description: |-
> + The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel
> + image sensor, which is the latest production derived from Omnivision's CMOS
> + image sensor technology. Ihis chip supports high frame rate speeds up to 30fps
> + @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The
> + sensor output is available via CSI-2 serial data output.
> +
> +properties:
> + compatible:
> + const: ovti,ov02a10
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> + clock-names:
> + description:
> + External clock for the sensor.
> + items:
> + - const: eclk
> +
> + clock-frequency:
> + description:
> + Frequency of the eclk clock in Hz.
> +
> + dovdd-supply:
> + description:
> + Definition of the regulator used as Digital I/O voltage supply.
> +
> + avdd-supply:
> + description:
> + Definition of the regulator used as Analog voltage supply.
> +
> + dvdd-supply:
> + description:
> + Definition of the regulator used as Digital core voltage supply.
> +
> + powerdown-gpios:
> + description:
> + Must be the device tree identifier of the GPIO connected to the
> + PD_PAD pin. This pin is used to place the OV02A10 into standby mode
> + or shutdown mode. As the line needs to be high for the powerdown mode
> + to be active, it should be marked GPIO_ACTIVE_HIGH.
> + maxItems: 1
> +
> + reset-gpios:
> + description:
> + Must be the device tree identifier of the GPIO connected to the
> + RST_PD pin. If specified, it will be asserted during driver probe.
> + As the line needs to be low for the reset to be active, it should be
> + marked GPIO_ACTIVE_LOW.
> + maxItems: 1
> +
> + rotation:
> + description:
> + Definition of the sensor's placement.
> + allOf:
> + - $ref: "/schemas/types.yaml#/definitions/uint32"
> + - enum:
> + - 0 # Sensor Mounted Upright
> + - 180 # Sensor Mounted Upside Down
> + default: 0
> +
> + ovti,mipi-clock-voltage:
> + description:
> + An array of 2-tuples items, and each item consists of link frequency and
> + MIPI clock voltage unit like <freq-kHz volt-unit>. Clock voltage unit is
> + dependent upon link speed, indicating MIPI transmission speed select that
> + controls D-PHY timing setting by adjusting MIPI clock voltage to improve
> + the clock driver capability.
> + $ref: "/schemas/types.yaml#/definitions/uint32-array"
> + minItems: 2
> + default: [390000, 4]
Why do you have the link frequency here as well?
In principle this does belong to the endpoint as link frequencies are
specific to that, but I don't mind; there's just a single port anyway.
> +
> + # See ../video-interfaces.txt for details
> + port:
> + type: object
> + additionalProperties: false
> + description:
> + Output port node, single endpoint describing the CSI-2 transmitter.
> +
> + properties:
> + endpoint:
> + type: object
> + additionalProperties: false
> +
> + properties:
> + link-frequencies: true
> + remote-endpoint: true
> +
> + required:
> + - link-frequencies
> + - remote-endpoint
> +
> + required:
> + - endpoint
> +
> +required:
> + - compatible
> + - reg
> + - clocks
> + - clock-names
> + - clock-frequency
> + - dovdd-supply
> + - avdd-supply
> + - dvdd-supply
> + - powerdown-gpios
> + - reset-gpios
> + - port
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ov02a10: camera-sensor at 3d {
> + compatible = "ovti,ov02a10";
> + reg = <0x3d>;
> +
> + powerdown-gpios = <&pio 107 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&pio 109 GPIO_ACTIVE_LOW>;
> +
> + clocks = <&ov02a10_clk>;
> + clock-names = "eclk";
> + clock-frequency = <24000000>;
> +
> + rotation = <180>;
> + ovti,mipi-clock-voltage = <390000 4>;
> +
> + dovdd-supply = <&ov02a10_dovdd>;
> + avdd-supply = <&ov02a10_avdd>;
> + dvdd-supply = <&ov02a10_dvdd>;
> +
> + port {
> + wcam_out: endpoint {
> + link-frequencies = /bits/ 64 <390000000>;
> + remote-endpoint = <&mipi_in_wcam>;
> + };
> + };
> + };
> + };
> +
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index deaafb6..48aa7a7 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12718,6 +12718,13 @@ M: Harald Welte <laforge at gnumonks.org>
> S: Maintained
> F: drivers/char/pcmcia/cm4040_cs.*
>
> +OMNIVISION OV02A10 SENSOR DRIVER
> +M: Dongchun Zhu <dongchun.zhu at mediatek.com>
> +L: linux-media at vger.kernel.org
> +S: Maintained
> +T: git git://linuxtv.org/media_tree.git
> +F: Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml
> +
> OMNIVISION OV13858 SENSOR DRIVER
> M: Sakari Ailus <sakari.ailus at linux.intel.com>
> L: linux-media at vger.kernel.org
> --
> 2.9.2
--
Sakari Ailus
More information about the linux-arm-kernel
mailing list