[PATCH v3 1/3] dt-bindings: media: atmel: csi2dc: add bindings for microchip csi2dc
Jacopo Mondi
jacopo at jmondi.org
Mon Oct 12 09:04:25 EDT 2020
Hello,
just my 2 cents, as I've noticed this patch skimming through the
list
On Mon, Oct 12, 2020 at 07:19:43AM +0000, Eugen.Hristev at microchip.com wrote:
> On 11.10.2020 00:17, Laurent Pinchart wrote:
> > Hi Eugen,
> >
> > Thank you for the patch.
>
> Hi,
>
> Thank you for your review,
>
> >
> > On Wed, Aug 26, 2020 at 09:51:40AM +0300, Eugen Hristev wrote:
> >> Add bindings documentation for Microchip CSI2 Demultiplexer controller.
> >>
> >> CSI2DC is a demultiplexer from Synopsys IDI interface specification to
> >> parallel interface connection or direct memory access.
> >>
> >> Signed-off-by: Eugen Hristev <eugen.hristev at microchip.com>
> >> ---
> >> Changes in v3:
> >> - Removed some text from description, as it was explained in the schema
> >> - fixed other things as per Rob's review
> >> - moved some text inside the schema, like the clock description
> >>
> >> Changes in v2:
> >> - fixed warnings reported by dt_binding_check
> >>
> >> .../bindings/media/microchip,csi2dc.yaml | 174 ++++++++++++++++++
> >> 1 file changed, 174 insertions(+)
> >> create mode 100644 Documentation/devicetree/bindings/media/microchip,csi2dc.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml b/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml
> >> new file mode 100644
> >> index 000000000000..b4c1b8800a3b
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml
> >> @@ -0,0 +1,174 @@
> >> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/media/microchip,csi2dc.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: Microchip CSI2 Demux Controller (CSI2DC)
> >> +
> >> +maintainers:
> >> + - Eugen Hristev <eugen.hristev at microchip.com>
> >> +
> >> +description:
> >> + CSI2DC - Camera Serial Interface 2 Demux Controller
> >> +
> >> + CSI2DC is a hardware block that receives incoming data from an IDI interface
> >> + and filters packets based on their data type and virtual channel identifier,
> >> + then converts the byte stream into a cross clock domain to a pixel stream
> >> + to a parallel interface that can be read by a sensor controller.
> >> +
> >> + CSI2DC provides two pipes, one video pipe and one data pipe. Video pipe
> >> + is connected to a sensor controller and the data pipe is accessible
> >> + as a DMA slave port to a DMA controller.
> >> +
> >> + CSI2DC supports a single 'port' node as a source pad with Synopsys 32-bit
> >> + IDI interface. The connected endpoint must be a IDI interface compatible
> >> + device (like Synopsys CSI2HOST) , that can provide 32-bit IDI interface
> >> + connection as sink pad.
> >> + For media entity and endpoints please refer to the bindings defined in
> >> + Documentation/devicetree/bindings/media/video-interfaces.txt.
> >> + For Synopsys IDI interface please refer to
> >> + Documentation/devicetree/bindings/media/snps,dw-csi-plat.txt
> >> +
> >> + CSI2DC supports one 'port' node as sink pad with parallel interface. This is
> >> + called video pipe.
> >> + This port has an 'endpoint' can then be used as a source pad for another
> >> + controller (next in pipeline).
> >> + Please refer to the bindings defined in
> >> + Documentation/devicetree/bindings/media/video-interfaces.txt.
> >> +
> >> + CSI2DC also supports direct access to the data through AHB, via DMA channel,
> >> + called data pipe.
> >> + Because of this, the sink 'port' child node (second) is not mandatory.
> >> + If the sink 'port' child node is missing, only data pipe is available.
> >> +
> >> +properties:
> >> + compatible:
> >> + const: microchip,sama7g5-csi2dc
> >> +
> >> + reg:
> >> + maxItems: 1
> >> +
> >> + clocks:
> >> + maxItems: 2
> >> +
> >> + clock-names:
> >> + description:
> >> + CSI2DC must have two clocks to function correctly. One clock is the
> >> + peripheral clock for the inside functionality of the hardware block.
> >> + This is named 'pclk'. The second clock must be the cross domain clock,
> >> + in which CSI2DC will perform clock crossing. This clock must be fed
> >> + by the next controller in pipeline, which usually is a sensor controller.
> >> + Normally this clock should be given by this sensor controller who
> >> + is also a clock source. This clock is named 'scck', sensor controller clock.
> >> + items:
> >> + - const: pclk
> >> + - const: scck
> >> +
> >> + microchip,clk-gated:
> >> + type: boolean
> >> + description:
> >> + If present, indicates that the clock is gated.
> >> + Otherwise, the clock is free-running.
> >
> > I don't think this belongs to the DT bindings, it should instead be
> > queried from the source subdev at runtime.
>
> If this should be queried, do you know what is the v4l2 mechanism to
> query such information ?
> The subdevice is connected through a port interface to this device, so
> it was natural for me to fully describe the interface in the devicetree
> port description
>
Is this property describing the CSI-2 clock continuous, non-continuous
mode configuration, or did I mis-interpreted it ?
We added support for retrieving run-time configuration of the media
bus with the get_mbus_config pad operations recently. Among the
configuration flags for MBUS_CSI2_DPHY there are inded CONTINUOUS and
NON_CONTINUOUS clock flags.
> >
> >> +
> >> + microchip,inter-line-delay:
> >> + allOf:
> >> + - $ref: /schemas/types.yaml#/definitions/uint32
> >> + - minimum: 1
> >> + - maximum: 16
> >> + default: 16
> >> + description:
> >> + Indicates how many clock cycles should be introduced between each line.
> >
> > This also sounds like a configuration parameter. How does one compute
> > the right value for this ?
>
> I think this is a delay that can be added inside the hardware block,
> depending on the interface speed and bandwidth. I will try to understand
> more details from the hardware design and come back with a more detailed
> answer.
>
> >
> >> +
> >> + port at 0:
> >> + type: object
> >> + description:
> >> + Input port node, single endpoint describing the input pad.
> >> +
> >> + properties:
> >> + reg:
> >> + const: 0
> >> +
> >> + endpoint:
> >> + type: object
> >> +
> >> + properties:
> >> + remote-endpoint: true
> >> +
> >> + required:
> >> + - remote-endpoint
> >> +
> >> + additionalProperties: false
> >> +
> >> + additionalProperties: false
> >> +
> >> + port at 1:
> >> + type: object
> >> + description:
> >> + Output port node, single endpoint, describing the output pad.
> >> +
> >> + properties:
> >> + '#address-cells':
> >> + const: 1
> >> +
> >> + '#size-cells':
> >> + const: 0
> >> +
> >> + reg:
> >> + const: 1
> >> +
> >> + patternProperties:
> >> + "^endpoint@[0-3]$":
> >> + type: object
> >> +
> >> + properties:
> >> + reg:
> >> + enum: [0, 1, 2, 3]
> >> + description: virtual channel for the endpoint
> >
> > The virtual channel used by the source is also something that needs to
> > be queried from the source at runtime, it doesn't belong to this
> > binding.
>
> The same question as for the gated clock configuration. How can we use
> v4l2 subdevice API to obtain such information from the subdevice? And if
> the subdevice does not offer such information ?
I think the subdev driver should be instrumented to report it instead of
hard-coding the information in DT which should be otherwise updated
depending on which sensor is connected to the board. Does it make
sense to you ?
Cheers
j
>
> Thanks again,
>
> Eugen
> >
> >> +
> >> + remote-endpoint: true
> >> +
> >> + required:
> >> + - remote-endpoint
> >> + - reg
> >> +
> >> + additionalProperties: false
> >> +
> >> + additionalProperties: false
> >> +
> >> +required:
> >> + - compatible
> >> + - reg
> >> + - clocks
> >> + - clock-names
> >> + - port at 0
> >> +
> >> +examples:
> >> + - |
> >> + csi2dc at e1404000 {
> >> + compatible = "microchip,sama7g5-csi2dc";
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + reg = <0xe1404000 0x500>;
> >> + clocks = <&pclk>, <&scck>;
> >> + clock-names = "pclk", "scck";
> >> +
> >> + port at 0 {
> >> + reg = <0>; /* must be 0, first child port */
> >> + csi2dc_in: endpoint { /* input from IDI interface */
> >> + remote-endpoint = <&csi2host_out>;
> >> + };
> >> + };
> >> +
> >> + port at 1 {
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + reg = <1>; /* must be 1, second child port */
> >> + csi2dc_out: endpoint at 2 {
> >> + reg = <2>; /* virtual channel identifier */
> >> + remote-endpoint = <&xisc_in>; /* output to sensor controller */
> >> + };
> >> + };
> >> + };
> >> +
> >> +...
> >
> > --
> > Regards,
> >
> > Laurent Pinchart
> >
>
More information about the linux-arm-kernel
mailing list