[PATCH v4 4/4] mmc: sdhci-of-arasan: Enable UHS-1 support for Keem Bay SOC

Ulf Hansson ulf.hansson at linaro.org
Fri Oct 9 02:56:25 EDT 2020


On Thu, 8 Oct 2020 at 19:21, Zulkifli, Muhammad Husaini
<muhammad.husaini.zulkifli at intel.com> wrote:
>
> Hi,
>
> >-----Original Message-----
> >From: Ulf Hansson <ulf.hansson at linaro.org>
> >Sent: Thursday, October 8, 2020 11:19 PM
> >To: Zulkifli, Muhammad Husaini <muhammad.husaini.zulkifli at intel.com>
> >Cc: Hunter, Adrian <adrian.hunter at intel.com>; Michal Simek
> ><michal.simek at xilinx.com>; Shevchenko, Andriy
> ><andriy.shevchenko at intel.com>; linux-mmc at vger.kernel.org; Linux ARM
> ><linux-arm-kernel at lists.infradead.org>; Linux Kernel Mailing List <linux-
> >kernel at vger.kernel.org>; Raja Subramanian, Lakshmi Bai
> ><lakshmi.bai.raja.subramanian at intel.com>; Wan Mohamad, Wan Ahmad
> >Zainie <wan.ahmad.zainie.wan.mohamad at intel.com>; Arnd Bergmann
> ><arnd at arndb.de>
> >Subject: Re: [PATCH v4 4/4] mmc: sdhci-of-arasan: Enable UHS-1 support for
> >Keem Bay SOC
> >
> >On Thu, 8 Oct 2020 at 12:54, Zulkifli, Muhammad Husaini
> ><muhammad.husaini.zulkifli at intel.com> wrote:
> >>
> >> Hi,
> >>
> >> >-----Original Message-----
> >> >From: Ulf Hansson <ulf.hansson at linaro.org>
> >> >Sent: Thursday, October 8, 2020 5:28 PM
> >> >To: Zulkifli, Muhammad Husaini <muhammad.husaini.zulkifli at intel.com>
> >> >Cc: Hunter, Adrian <adrian.hunter at intel.com>; Michal Simek
> >> ><michal.simek at xilinx.com>; Shevchenko, Andriy
> >> ><andriy.shevchenko at intel.com>; linux-mmc at vger.kernel.org; Linux ARM
> >> ><linux-arm-kernel at lists.infradead.org>; Linux Kernel Mailing List
> >> ><linux- kernel at vger.kernel.org>; Raja Subramanian, Lakshmi Bai
> >> ><lakshmi.bai.raja.subramanian at intel.com>; Wan Mohamad, Wan Ahmad
> >> >Zainie <wan.ahmad.zainie.wan.mohamad at intel.com>; Arnd Bergmann
> >> ><arnd at arndb.de>
> >> >Subject: Re: [PATCH v4 4/4] mmc: sdhci-of-arasan: Enable UHS-1
> >> >support for Keem Bay SOC
> >> >
> >> >On Thu, 8 Oct 2020 at 04:12, <muhammad.husaini.zulkifli at intel.com>
> >wrote:
> >> >>
> >> >> From: Muhammad Husaini Zulkifli
> >> >> <muhammad.husaini.zulkifli at intel.com>
> >> >>
> >> >> Voltage switching sequence is needed to support UHS-1 interface.
> >> >> There are 2 places to control the voltage.
> >> >> 1) By setting the AON register using firmware driver calling
> >> >> system-level platform management layer (SMC) to set the register.
> >> >> 2) By controlling the GPIO expander value to drive either 1.8V or
> >> >> 3.3V for power mux input.
> >> >>
> >> >> Signed-off-by: Muhammad Husaini Zulkifli
> >> >> <muhammad.husaini.zulkifli at intel.com>
> >> >> Reviewed-by: Andy Shevchenko <andriy.shevchenko at intel.com>
> >> >> Reviewed-by: Adrian Hunter <adrian.hunter at intel.com>
> >> >> ---
> >> >>  drivers/mmc/host/sdhci-of-arasan.c | 126
> >> >> +++++++++++++++++++++++++++++
> >> >>  1 file changed, 126 insertions(+)
> >> >>
> >> >> diff --git a/drivers/mmc/host/sdhci-of-arasan.c
> >> >> b/drivers/mmc/host/sdhci-of-arasan.c
> >> >> index 46aea6516133..ea2467b0073d 100644
> >> >> --- a/drivers/mmc/host/sdhci-of-arasan.c
> >> >> +++ b/drivers/mmc/host/sdhci-of-arasan.c
> >> >> @@ -16,6 +16,7 @@
> >> >>   */
> >> >>
> >> >>  #include <linux/clk-provider.h>
> >> >> +#include <linux/gpio/consumer.h>
> >> >>  #include <linux/mfd/syscon.h>
> >> >>  #include <linux/module.h>
> >> >>  #include <linux/of_device.h>
> >> >> @@ -23,6 +24,7 @@
> >> >>  #include <linux/regmap.h>
> >> >>  #include <linux/of.h>
> >> >>  #include <linux/firmware/xlnx-zynqmp.h>
> >> >> +#include <linux/firmware/intel/keembay_firmware.h>
> >> >>
> >> >>  #include "cqhci.h"
> >> >>  #include "sdhci-pltfm.h"
> >> >> @@ -136,6 +138,7 @@ struct sdhci_arasan_clk_data {
> >> >>   * @soc_ctl_base:      Pointer to regmap for syscon for soc_ctl registers.
> >> >>   * @soc_ctl_map:       Map to get offsets into soc_ctl registers.
> >> >>   * @quirks:            Arasan deviations from spec.
> >> >> + * @uhs_gpio:          Pointer to the uhs gpio.
> >> >>   */
> >> >>  struct sdhci_arasan_data {
> >> >>         struct sdhci_host *host;
> >> >> @@ -150,6 +153,7 @@ struct sdhci_arasan_data {
> >> >>         struct regmap   *soc_ctl_base;
> >> >>         const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
> >> >>         unsigned int    quirks;
> >> >> +       struct gpio_desc *uhs_gpio;
> >> >>
> >> >>  /* Controller does not have CD wired and will not function
> >> >> normally without
> >> >*/
> >> >>  #define SDHCI_ARASAN_QUIRK_FORCE_CDTEST        BIT(0)
> >> >> @@ -361,6 +365,112 @@ static int sdhci_arasan_voltage_switch(struct
> >> >mmc_host *mmc,
> >> >>         return -EINVAL;
> >> >>  }
> >> >>
> >> >> +static int sdhci_arasan_keembay_voltage_switch(struct mmc_host
> >*mmc,
> >> >> +                                      struct mmc_ios *ios) {
> >> >> +       struct sdhci_host *host = mmc_priv(mmc);
> >> >> +       struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> >> >> +       struct sdhci_arasan_data *sdhci_arasan =
> >sdhci_pltfm_priv(pltfm_host);
> >> >> +       u16 ctrl_2, clk;
> >> >> +       int ret;
> >> >> +
> >> >> +       switch (ios->signal_voltage) {
> >> >> +       case MMC_SIGNAL_VOLTAGE_180:
> >> >> +               clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
> >> >> +               clk &= ~SDHCI_CLOCK_CARD_EN;
> >> >> +               sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
> >> >> +
> >> >> +               clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
> >> >> +               if (clk & SDHCI_CLOCK_CARD_EN)
> >> >> +                       return -EAGAIN;
> >> >> +
> >> >> +               sdhci_writeb(host, SDHCI_POWER_ON | SDHCI_POWER_180,
> >> >> +                                  SDHCI_POWER_CONTROL);
> >> >> +
> >> >> +               /*
> >> >> +                * Set VDDIO_B voltage to Low for 1.8V
> >> >> +                * which is controlling by GPIO Expander.
> >> >> +                */
> >> >> +               gpiod_set_value_cansleep(sdhci_arasan->uhs_gpio,
> >> >> + 0);
> >> >> +
> >> >> +               /*
> >> >> +                * This is like a final gatekeeper. Need to ensure changed
> >voltage
> >> >> +                * is settled before and after turn on this bit.
> >> >> +                */
> >> >> +               usleep_range(1000, 1100);
> >> >> +
> >> >> +               ret =
> >keembay_sd_voltage_selection(KEEMBAY_SET_1V8_VOLT);
> >> >> +               if (ret)
> >> >> +                       return ret;
> >> >> +
> >> >> +               usleep_range(1000, 1100);
> >> >
> >> >No, sorry, but I don't like this.
> >> >
> >> >This looks like a GPIO regulator with an extension of using the
> >> >keembay_sd_voltage_selection() thingy. I think you can model these
> >> >things behind a regulator and hook it up as a vqmmc supply in DT
> >> >instead. BTW, this is the common way we deal with these things for mmc
> >host drivers.
> >>
> >> The SDcard for Keem Bay SOC does not have its own voltage regulator.
> >> There are 2 places to control the voltage.
> >> 1) By setting the AON register calling system-level platform management
> >layer (SMC)
> >>    to set the I/O pads voltage for particular GPIOs line for clk,data and cmd.
> >>    The reason why I use this keembay_sd_voltage_selection() via smccc
> >interface it because during voltage switching
> >>    I need to access to AON register. On a secure system, we could not
> >directly access to AON register due to some security concern from driver side,
> >thus
> >>    cannot exposed any register or address.
> >> 2) By controlling the GPIO expander value to drive either 1.8V or 3.3V for
> >power mux input.
> >
> >I see, thanks for clarifying.
> >
> >To me, it sounds like the best fit is to implement a pinctrl (to manage the I/O
> >pads) and a GPIO regulator.
> >
> Even with pinctrl, i still need to use the keembay_sd_voltage_selection() thingy for AON register.

Yes, I am fine by that.

Although, as it's really a pinctrl, it deserves to be modelled like
that. Not as a soc specific hack in a mmc host driver.

> Plus, the GPIO pin that control the sd-voltage is in GPIO Expander not using Keembay SOC GPIO Pin.
> The best option is using the gpio consumer function to toggle the pin.

As I said, please no.

The common way to model this is as a GPIO regulator. In this way, you
can even rely on existing mmc DT bindings. All you have to do is to
hook up a vqmmc supply to the mmc node.

To be clear, as long as there are no arguments for why a pinctrl and
GPIO regulator can't be used - I am not going to pick up the patches.

Kind regards
Uffe



More information about the linux-arm-kernel mailing list