[PATCH v5] arm64: dts: marvell: add DT for ESPRESSObin-Ultra

[Gregory CLEMENT]

Hi Vladimir,

> This adds support for ESPRESSObin-Ultra from Globalscale.
>
> Specifications are similar to the base ESPRESSObin board, with main
> difference being being WAN port with PoE capability and 2 additional ethernet ports.
>
> Full specifications:
>
> 1x Marvell 64 bit Dual Core ARM A53 Armada 3700 SOC clocked up to 1.2Ghz
> 1x Topaz 6341 Networking Switch
> 1GB DDR4
> 8GB eMMC
> 1x WAN with 30W POE
> 4x Gb LAN
> 1x RTC Clock and battery
> 1x DC Jack
> 1x USB 3.0 Type A
> 1x USB 2.0 Type A
> 1x SIM NanoSIM card Slot
> 1x Power Button
> 4x LED
> 1x Reset button
> 1x microUSB for UART
> 1x M.2 2280 slot for memory
> 1x 2x2 802.11ac Wi-Fi
> 1x MiniPCIE slot for Wi-Fi (PCIe interface)
>
> Signed-off-by: Vladimir Vid <vladimir.vid at sartura.hr>


Applied on mvebu/dt64

I know that usb3 node is not yet enabled but we are a really close to the
end of the merge window for ARM so let's have this version in 5.11, and
then we can improve it in future version.

Thanks,

Gregory

> ---
>
> v5 changes:
> - update ethernet-phy at 1 to match reg value
>
> ---
>  arch/arm64/boot/dts/marvell/Makefile          |   1 +
>  .../marvell/armada-3720-espressobin-ultra.dts | 165 ++++++++++++++++++
>  2 files changed, 166 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
>
> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> index 3e5f2e7a040c..094f451fdd1d 100644
> --- a/arch/arm64/boot/dts/marvell/Makefile
> +++ b/arch/arm64/boot/dts/marvell/Makefile
> @@ -3,6 +3,7 @@
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
> +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
> new file mode 100644
> index 000000000000..c5eb3604dd5b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
> @@ -0,0 +1,165 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for ESPRESSObin-Ultra board.
> + * Copyright (C) 2019 Globalscale technologies, Inc.
> + *
> + * Jason Hung <jhung at globalscaletechnologies.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "armada-3720-espressobin.dtsi"
> +
> +/ {
> +	model = "Globalscale Marvell ESPRESSOBin Ultra Board";
> +	compatible = "globalscale,espressobin-ultra", "marvell,armada3720",
> +		     "marvell,armada3710";
> +
> +	aliases {
> +		/* ethernet1 is WAN port */
> +		ethernet1 = &switch0port5;
> +		ethernet2 = &switch0port1;
> +		ethernet3 = &switch0port2;
> +		ethernet4 = &switch0port3;
> +		ethernet5 = &switch0port4;
> +	};
> +
> +	reg_usb3_vbus: usb3-vbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb3-vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		gpio = <&gpionb 19 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	usb3_phy: usb3-phy {
> +		compatible = "usb-nop-xceiv";
> +		vcc-supply = <&reg_usb3_vbus>;
> +	};
> +
> +	gpio-leds {
> +		pinctrl-names = "default";
> +		compatible = "gpio-leds";
> +		/* No assigned functions to the LEDs by default */
> +		led1 {
> +			label = "ebin-ultra:blue:led1";
> +			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
> +		};
> +		led2 {
> +			label = "ebin-ultra:green:led2";
> +			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
> +		};
> +		led3 {
> +			label = "ebin-ultra:red:led3";
> +			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
> +		};
> +		led4 {
> +			label = "ebin-ultra:yellow:led4";
> +			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +};
> +
> +&sdhci0 {
> +	status = "okay";
> +};
> +
> +&sdhci1 {
> +	status = "disabled";
> +};
> +
> +&spi0 {
> +	flash at 0 {
> +		spi-max-frequency = <108000000>;
> +		spi-rx-bus-width = <4>;
> +		spi-tx-bus-width = <4>;
> +
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			partition at 0 {
> +				label = "firmware";
> +				reg = <0x0 0x3e0000>;
> +			};
> +			partition at 3e0000 {
> +				label = "hw-info";
> +				reg = <0x3e0000 0x10000>;
> +				read-only;
> +			};
> +			partition at 3f0000 {
> +				label = "u-boot-env";
> +				reg = <0x3f0000 0x10000>;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c1_pins>;
> +
> +	clock-frequency = <100000>;
> +
> +	rtc at 51 {
> +		compatible = "nxp,pcf8563";
> +		reg = <0x51>;
> +	};
> +};
> +
> +&usb3 {
> +	usb-phy = <&usb3_phy>;
> +	status = "disabled";
> +};
> +
> +&mdio {
> +	extphy: ethernet-phy at 1 {
> +		reg = <1>;
> +	};
> +};
> +
> +&switch0 {
> +	reg = <3>;
> +
> +	ports {
> +		switch0port1: port at 1 {
> +			reg = <1>;
> +			label = "lan0";
> +			phy-handle = <&switch0phy0>;
> +		};
> +
> +		switch0port2: port at 2 {
> +			reg = <2>;
> +			label = "lan1";
> +			phy-handle = <&switch0phy1>;
> +		};
> +
> +		switch0port3: port at 3 {
> +			reg = <3>;
> +			label = "lan2";
> +			phy-handle = <&switch0phy2>;
> +		};
> +
> +		switch0port4: port at 4 {
> +			reg = <4>;
> +			label = "lan3";
> +			phy-handle = <&switch0phy3>;
> +		};
> +
> +		switch0port5: port at 5 {
> +			reg = <5>;
> +			label = "wan";
> +			phy-handle = <&extphy>;
> +			phy-mode = "sgmii";
> +		};
> +	};
> +
> +	mdio {
> +		switch0phy3: switch0phy3 at 14 {
> +			reg = <0x14>;
> +		};
> +	};
> +};
> -- 
> 2.27.0
>

-- 
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com