[PATCH v3 1/3] mmc: sdhci-of-aspeed: Expose phase delay tuning
Andrew Jeffery
andrew at aj.id.au
Mon Nov 23 01:30:02 EST 2020
The Aspeed SD/eMMC controllers feature up to two SDHCIs alongside a
a set of "global" configuration registers. The global configuration
registers house controller-specific settings that aren't exposed by the
SDHCI, one example being a register for phase tuning.
The phase tuning feature is new in the AST2600 design. It's exposed as a
single register in the global register set and controls both the input
and output phase adjustment for each slot. As the settings are
slot-specific, the values to program are extracted from properties in
the SDHCI devicetree nodes.
Signed-off-by: Andrew Jeffery <andrew at aj.id.au>
---
drivers/mmc/host/sdhci-of-aspeed.c | 275 ++++++++++++++++++++++++++++-
1 file changed, 267 insertions(+), 8 deletions(-)
diff --git a/drivers/mmc/host/sdhci-of-aspeed.c b/drivers/mmc/host/sdhci-of-aspeed.c
index 4f008ba3280e..9fda2e7c1d78 100644
--- a/drivers/mmc/host/sdhci-of-aspeed.c
+++ b/drivers/mmc/host/sdhci-of-aspeed.c
@@ -6,6 +6,7 @@
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/io.h>
+#include <linux/math64.h>
#include <linux/mmc/host.h>
#include <linux/module.h>
#include <linux/of_address.h>
@@ -16,9 +17,19 @@
#include "sdhci-pltfm.h"
-#define ASPEED_SDC_INFO 0x00
-#define ASPEED_SDC_S1MMC8 BIT(25)
-#define ASPEED_SDC_S0MMC8 BIT(24)
+#define ASPEED_SDC_INFO 0x00
+#define ASPEED_SDC_S1_MMC8 BIT(25)
+#define ASPEED_SDC_S0_MMC8 BIT(24)
+#define ASPEED_SDC_PHASE 0xf4
+#define ASPEED_SDC_S1_PHASE_IN GENMASK(25, 21)
+#define ASPEED_SDC_S0_PHASE_IN GENMASK(20, 16)
+#define ASPEED_SDC_S1_PHASE_OUT GENMASK(15, 11)
+#define ASPEED_SDC_S1_PHASE_IN_EN BIT(10)
+#define ASPEED_SDC_S1_PHASE_OUT_EN GENMASK(9, 8)
+#define ASPEED_SDC_S0_PHASE_OUT GENMASK(7, 3)
+#define ASPEED_SDC_S0_PHASE_IN_EN BIT(2)
+#define ASPEED_SDC_S0_PHASE_OUT_EN GENMASK(1, 0)
+#define ASPEED_SDC_PHASE_MAX 31
struct aspeed_sdc {
struct clk *clk;
@@ -28,9 +39,42 @@ struct aspeed_sdc {
void __iomem *regs;
};
+struct aspeed_sdhci_tap_param {
+ bool set;
+
+#define ASPEED_SDHCI_TAP_PARAM_INVERT_CLK BIT(4)
+ u8 in;
+ u8 out;
+};
+
+struct aspeed_sdhci_phase_tap_desc {
+ u32 tap_mask;
+ u32 enable_mask;
+ u8 enable_value;
+};
+
+struct aspeed_sdhci_phase_desc {
+ struct aspeed_sdhci_phase_tap_desc in;
+ struct aspeed_sdhci_phase_tap_desc out;
+};
+
+struct aspeed_sdhci_phase_param {
+ bool set;
+ u8 in_deg;
+ u8 out_deg;
+};
+
+struct aspeed_sdhci_pdata {
+ const struct aspeed_sdhci_phase_desc *phase_desc;
+ size_t nr_phase_descs;
+};
+
struct aspeed_sdhci {
+ const struct aspeed_sdhci_pdata *pdata;
struct aspeed_sdc *parent;
u32 width_mask;
+ const struct aspeed_sdhci_phase_desc *phase_desc;
+ struct aspeed_sdhci_phase_param phase_param[MMC_TIMING_MMC_HS200 + 1];
};
static void aspeed_sdc_configure_8bit_mode(struct aspeed_sdc *sdc,
@@ -50,10 +94,119 @@ static void aspeed_sdc_configure_8bit_mode(struct aspeed_sdc *sdc,
spin_unlock(&sdc->lock);
}
+static u32
+aspeed_sdc_set_phase_tap(const struct aspeed_sdhci_phase_tap_desc *desc,
+ u8 tap, bool enable, u32 reg)
+{
+ reg &= ~(desc->enable_mask | desc->tap_mask);
+ if (enable) {
+ reg |= tap << __ffs(desc->tap_mask);
+ reg |= desc->enable_value << __ffs(desc->enable_mask);
+ }
+
+ return reg;
+}
+
+static void
+aspeed_sdc_set_phase_taps(struct aspeed_sdc *sdc,
+ const struct aspeed_sdhci_phase_desc *desc,
+ const struct aspeed_sdhci_tap_param *taps)
+{
+ u32 reg;
+
+ spin_lock(&sdc->lock);
+ reg = readl(sdc->regs + ASPEED_SDC_PHASE);
+
+ reg = aspeed_sdc_set_phase_tap(&desc->in, taps->in, taps->set, reg);
+ reg = aspeed_sdc_set_phase_tap(&desc->out, taps->out, taps->set, reg);
+
+ writel(reg, sdc->regs + ASPEED_SDC_PHASE);
+ spin_unlock(&sdc->lock);
+}
+
+#define PICOSECONDS_PER_SECOND 1000000000000ULL
+#define ASPEED_SDHCI_NR_TAPS 15
+/* Measured value with *handwave* environmentals and static loading */
+#define ASPEED_SDHCI_MAX_TAP_DELAY_PS 1253
+static int aspeed_sdhci_phase_to_tap(struct sdhci_host *host,
+ unsigned long rate_hz, int phase_deg)
+{
+ u64 phase_period_ps;
+ struct device *dev;
+ u64 prop_delay_ps;
+ u64 clk_period_ps;
+ unsigned int taps;
+ u8 inverted;
+
+ dev = host->mmc->parent;
+
+ phase_deg %= 360;
+
+ if (phase_deg >= 180) {
+ inverted = ASPEED_SDHCI_TAP_PARAM_INVERT_CLK;
+ phase_deg -= 180;
+ dev_dbg(dev,
+ "Inverting clock to reduce phase correction from %d to %d degrees\n",
+ phase_deg + 180, phase_deg);
+ } else {
+ inverted = 0;
+ }
+
+ prop_delay_ps = ASPEED_SDHCI_MAX_TAP_DELAY_PS / ASPEED_SDHCI_NR_TAPS;
+ clk_period_ps = div_u64(PICOSECONDS_PER_SECOND, (u64)rate_hz);
+ phase_period_ps = div_u64((u64)phase_deg * clk_period_ps, 360ULL);
+
+ taps = div_u64(phase_period_ps, prop_delay_ps);
+ if (taps > ASPEED_SDHCI_NR_TAPS) {
+ dev_warn(dev,
+ "Requested out of range phase tap %d for %d degrees of phase compensation at %luHz, clamping to tap %d\n",
+ taps, phase_deg, rate_hz, ASPEED_SDHCI_NR_TAPS);
+ taps = ASPEED_SDHCI_NR_TAPS;
+ }
+
+ return inverted | taps;
+}
+
+static void
+aspeed_sdhci_phases_to_taps(struct sdhci_host *host, unsigned long rate,
+ const struct aspeed_sdhci_phase_param *phases,
+ struct aspeed_sdhci_tap_param *taps)
+{
+ taps->set = phases->set;
+
+ if (!phases->set)
+ return;
+
+ taps->in = aspeed_sdhci_phase_to_tap(host, rate, phases->in_deg);
+ taps->out = aspeed_sdhci_phase_to_tap(host, rate, phases->out_deg);
+}
+
+static void
+aspeed_sdhci_configure_phase(struct sdhci_host *host, unsigned long rate)
+{
+ struct aspeed_sdhci_tap_param _taps = {0}, *taps = &_taps;
+ struct aspeed_sdhci_phase_param *phases;
+ struct aspeed_sdhci *sdhci;
+
+ sdhci = sdhci_pltfm_priv(sdhci_priv(host));
+
+ if (!sdhci->phase_desc)
+ return;
+
+ phases = &sdhci->phase_param[host->timing];
+ aspeed_sdhci_phases_to_taps(host, rate, phases, taps);
+ aspeed_sdc_set_phase_taps(sdhci->parent, sdhci->phase_desc, taps);
+ dev_dbg(host->mmc->parent,
+ "Using taps [%d, %d] for [%d, %d] degrees of phase correction at %luHz (%d)\n",
+ taps->in & ASPEED_SDHCI_NR_TAPS,
+ taps->out & ASPEED_SDHCI_NR_TAPS,
+ phases->in_deg, phases->out_deg, rate, host->timing);
+}
+
static void aspeed_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
{
struct sdhci_pltfm_host *pltfm_host;
- unsigned long parent;
+ unsigned long parent, bus;
int div;
u16 clk;
@@ -69,13 +222,17 @@ static void aspeed_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
clock = host->max_clk;
for (div = 2; div < 256; div *= 2) {
- if ((parent / div) <= clock)
+ bus = parent / div;
+ if (bus <= clock)
break;
}
+
div >>= 1;
clk = div << SDHCI_DIVIDER_SHIFT;
+ aspeed_sdhci_configure_phase(host, bus);
+
sdhci_enable_clk(host, clk);
}
@@ -155,8 +312,60 @@ static inline int aspeed_sdhci_calculate_slot(struct aspeed_sdhci *dev,
return (delta / 0x100) - 1;
}
+static void
+aspeed_sdhci_of_parse_phase(struct device_node *np, const char *prop,
+ struct aspeed_sdhci_phase_param *phase)
+{
+ int degrees[2] = {0};
+ int rc;
+
+ rc = of_property_read_variable_u32_array(np, prop, degrees, 2, 0);
+ phase->set = rc == 2;
+ if (phase->set) {
+ phase->in_deg = degrees[0];
+ phase->out_deg = degrees[1];
+ }
+}
+
+static int aspeed_sdhci_of_parse(struct platform_device *pdev,
+ struct aspeed_sdhci *sdhci)
+{
+ struct device_node *np;
+ struct device *dev;
+
+ if (!sdhci->phase_desc)
+ return 0;
+
+ dev = &pdev->dev;
+ np = dev->of_node;
+
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-legacy",
+ &sdhci->phase_param[MMC_TIMING_LEGACY]);
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-mmc-hs",
+ &sdhci->phase_param[MMC_TIMING_MMC_HS]);
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-sd-hs",
+ &sdhci->phase_param[MMC_TIMING_SD_HS]);
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-uhs-sdr12",
+ &sdhci->phase_param[MMC_TIMING_UHS_SDR12]);
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-uhs-sdr25",
+ &sdhci->phase_param[MMC_TIMING_UHS_SDR25]);
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-uhs-sdr50",
+ &sdhci->phase_param[MMC_TIMING_UHS_SDR50]);
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-uhs-sdr104",
+ &sdhci->phase_param[MMC_TIMING_UHS_SDR104]);
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-uhs-ddr50",
+ &sdhci->phase_param[MMC_TIMING_UHS_DDR50]);
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-mmc-ddr52",
+ &sdhci->phase_param[MMC_TIMING_MMC_DDR52]);
+ aspeed_sdhci_of_parse_phase(np, "clk-phase-mmc-hs200",
+ &sdhci->phase_param[MMC_TIMING_MMC_HS200]);
+
+ return 0;
+}
+
static int aspeed_sdhci_probe(struct platform_device *pdev)
{
+ const struct aspeed_sdhci_pdata *aspeed_pdata;
struct sdhci_pltfm_host *pltfm_host;
struct aspeed_sdhci *dev;
struct sdhci_host *host;
@@ -164,12 +373,15 @@ static int aspeed_sdhci_probe(struct platform_device *pdev)
int slot;
int ret;
+ aspeed_pdata = of_device_get_match_data(&pdev->dev);
+
host = sdhci_pltfm_init(pdev, &aspeed_sdhci_pdata, sizeof(*dev));
if (IS_ERR(host))
return PTR_ERR(host);
pltfm_host = sdhci_priv(host);
dev = sdhci_pltfm_priv(pltfm_host);
+ dev->pdata = aspeed_pdata;
dev->parent = dev_get_drvdata(pdev->dev.parent);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -180,8 +392,17 @@ static int aspeed_sdhci_probe(struct platform_device *pdev)
else if (slot >= 2)
return -EINVAL;
- dev_info(&pdev->dev, "Configuring for slot %d\n", slot);
- dev->width_mask = !slot ? ASPEED_SDC_S0MMC8 : ASPEED_SDC_S1MMC8;
+ if (dev->pdata && slot < dev->pdata->nr_phase_descs) {
+ dev->phase_desc = &dev->pdata->phase_desc[slot];
+ } else {
+ dev_info(&pdev->dev,
+ "Phase control not supported for slot %d\n", slot);
+ dev->phase_desc = NULL;
+ }
+
+ dev->width_mask = !slot ? ASPEED_SDC_S0_MMC8 : ASPEED_SDC_S1_MMC8;
+
+ dev_info(&pdev->dev, "Configured for slot %d\n", slot);
sdhci_get_of_property(pdev);
@@ -195,6 +416,10 @@ static int aspeed_sdhci_probe(struct platform_device *pdev)
goto err_pltfm_free;
}
+ ret = aspeed_sdhci_of_parse(pdev, dev);
+ if (ret)
+ goto err_sdhci_add;
+
ret = mmc_of_parse(host->mmc);
if (ret)
goto err_sdhci_add;
@@ -230,10 +455,44 @@ static int aspeed_sdhci_remove(struct platform_device *pdev)
return 0;
}
+static const struct aspeed_sdhci_phase_desc ast2600_sdhci_phase[] = {
+ /* SDHCI/Slot 0 */
+ [0] = {
+ .in = {
+ .tap_mask = ASPEED_SDC_S0_PHASE_IN,
+ .enable_mask = ASPEED_SDC_S0_PHASE_IN_EN,
+ .enable_value = 1,
+ },
+ .out = {
+ .tap_mask = ASPEED_SDC_S0_PHASE_OUT,
+ .enable_mask = ASPEED_SDC_S0_PHASE_OUT_EN,
+ .enable_value = 3,
+ },
+ },
+ /* SDHCI/Slot 1 */
+ [1] = {
+ .in = {
+ .tap_mask = ASPEED_SDC_S1_PHASE_IN,
+ .enable_mask = ASPEED_SDC_S1_PHASE_IN_EN,
+ .enable_value = 1,
+ },
+ .out = {
+ .tap_mask = ASPEED_SDC_S1_PHASE_OUT,
+ .enable_mask = ASPEED_SDC_S1_PHASE_OUT_EN,
+ .enable_value = 3,
+ },
+ },
+};
+
+static const struct aspeed_sdhci_pdata ast2600_sdhci_pdata = {
+ .phase_desc = ast2600_sdhci_phase,
+ .nr_phase_descs = ARRAY_SIZE(ast2600_sdhci_phase),
+};
+
static const struct of_device_id aspeed_sdhci_of_match[] = {
{ .compatible = "aspeed,ast2400-sdhci", },
{ .compatible = "aspeed,ast2500-sdhci", },
- { .compatible = "aspeed,ast2600-sdhci", },
+ { .compatible = "aspeed,ast2600-sdhci", .data = &ast2600_sdhci_pdata, },
{ }
};
--
2.27.0
More information about the linux-arm-kernel
mailing list