[PATCH v1 1/1] ARM: dts: sun8i: h3: Add initial NanoPi R1 support
Yu-Tung Chang
mtwget at gmail.com
Wed Nov 4 03:07:48 EST 2020
Maxime Ripard <maxime at cerno.tech> 于2020年11月3日周二 下午7:37写道：
>
> Hi!
>
> On Mon, Nov 02, 2020 at 06:01:57PM +0800, Yu-Tung Chang wrote:
> > The NanoPi R1 is a complete open source board developed
> > by FriendlyElec for makers, hobbyists, fans and etc.
> >
> > NanoPi R1 key features
> > - Allwinner H3, Quad-core Cortex-A7 at 1.2GHz
> > - 512MB/1GB DDR3 RAM
> > - 8GB eMMC
> > - microSD slot
> > - 10/100/1000M Ethernet x 1
> > - 10/100 Ethernet x 1
> > - Wifi 802.11b/g/n
> > - Bluetooth 4.0
> > - Serial Debug Port
> > - 5V 2A DC power-supply
> >
> > Signed-off-by: Yu-Tung Chang <mtwget at gmail.com>
> > ---
> > .../devicetree/bindings/arm/sunxi.yaml | 5 +
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts | 169 ++++++++++++++++++
> > 3 files changed, 175 insertions(+)
> > create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
> >
> > diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
> > index 0f23133672a3..54a1aaee7e22 100644
> > --- a/Documentation/devicetree/bindings/arm/sunxi.yaml
> > +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
> > @@ -251,6 +251,11 @@ properties:
> > - const: friendlyarm,nanopi-neo-plus2
> > - const: allwinner,sun50i-h5
> >
> > + - description: FriendlyARM NanoPi R1
> > + items:
> > + - const: friendlyarm,nanopi-r1
> > + - const: allwinner,sun8i-h3
> > +
> > - description: FriendlyARM ZeroPi
> > items:
> > - const: friendlyarm,zeropi
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 4f0adfead547..aabaf67f86ed 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -1192,6 +1192,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> > sun8i-h3-nanopi-m1-plus.dtb \
> > sun8i-h3-nanopi-neo.dtb \
> > sun8i-h3-nanopi-neo-air.dtb \
> > + sun8i-h3-nanopi-r1.dtb \
> > sun8i-h3-orangepi-2.dtb \
> > sun8i-h3-orangepi-lite.dtb \
> > sun8i-h3-orangepi-one.dtb \
> > diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
> > new file mode 100644
> > index 000000000000..204a39f93f4e
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
> > @@ -0,0 +1,169 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (C) 2019 Igor Pecovnik <igor at armbian.com>
> > + * Copyright (C) 2020 Jayantajit Gogoi <jayanta.gogoi525 at gmail.com>
> > + * Copyright (C) 2020 Yu-Tung Chang <mtwget at gmail.com>
> > +*/
> > +
> > +#include "sun8i-h3-nanopi.dtsi"
> > +#include <dt-bindings/leds/common.h>
> > +
> > +/ {
> > + model = "FriendlyARM NanoPi R1";
> > + compatible = "friendlyarm,nanopi-r1", "allwinner,sun8i-h3";
> > +
> > + aliases {
> > + serial1 = &uart1;
> > + ethernet0 = &emac;
> > + ethernet1 = &wifi;
> > + };
> > +
> > + reg_gmac_3v3: gmac-3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "gmac-3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + startup-delay-us = <100000>;
> > + enable-active-high;
> > + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
> > + };
> > +
> > + reg_vdd_cpux: gpio-regulator {
> > + compatible = "regulator-gpio";
> > + regulator-name = "vdd-cpux";
> > + regulator-type = "voltage";
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1300000>;
> > + regulator-ramp-delay = <50>;
> > + gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
> > + gpios-states = <0x1>;
> > + states = <1100000 0x0
> > + 1300000 0x1>;
> > + };
> > +
> > + wifi_pwrseq: wifi_pwrseq {
> > + compatible = "mmc-pwrseq-simple";
> > + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > + clocks = <&rtc 1>;
> > + clock-names = "ext_clock";
> > + };
> > +
> > + leds {
> > + led-2 {
> > + function = LED_FUNCTION_WAN;
> > + color = <LED_COLOR_ID_GREEN>;
> > + gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> > + };
> > +
> > + led-3 {
> > + function = LED_FUNCTION_LAN;
> > + color = <LED_COLOR_ID_GREEN>;
> > + gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>; /* PA9 */
> > + };
> > + };
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <®_vdd_cpux>;
> > +};
> > +
> > +&ehci1 {
> > + status = "okay";
> > +};
> > +
> > +&ehci2 {
> > + status = "okay";
> > +};
> > +
> > +&emac {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&emac_rgmii_pins>;
> > + phy-supply = <®_gmac_3v3>;
> > + phy-handle = <&ext_rgmii_phy>;
> > + phy-mode = "rgmii-id";
> > + status = "okay";
> > +};
> > +
> > +&external_mdio {
> > + ext_rgmii_phy: ethernet-phy at 7 {
> > + compatible = "ethernet-phy-ieee802.3-c22";
> > + reg = <7>;
> > + };
> > +};
> > +
> > +&mmc1 {
> > + vmmc-supply = <®_vcc3v3>;
> > + vqmmc-supply = <®_vcc3v3>;
> > + mmc-pwrseq = <&wifi_pwrseq>;
> > + bus-width = <4>;
> > + non-removable;
> > + status = "okay";
> > +
> > + wifi: wifi at 1 {
> > + reg = <1>;
> > + compatible = "brcm,bcm4329-fmac";
> > + interrupt-parent = <&pio>;
> > + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
> > + interrupt-names = "host-wake";
> > + };
> > +};
> > +
> > +&mmc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc2_8bit_pins>;
> > + vmmc-supply = <®_vcc3v3>;
> > + vqmmc-supply = <®_vcc3v3>;
> > + bus-width = <8>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&ohci1 {
> > + status = "okay";
> > +};
> > +
> > +&ohci2 {
> > + status = "okay";
> > +};
> > +
> > +®_usb0_vbus {
> > + gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart1_pins>;
>
> This should be already set in the DTSI
>
uart0 as the debugging interface, uart1 as the external uart port,
uart3 as the bluetooth.
> > + status = "okay";
> > +};
>
> What is this UART used for?
>
uart1 as the external uart port, use a separate physical interface.
> Thanks!
> Maxime
Maxime Ripard <maxime at cerno.tech> 于2020年11月3日周二 下午7:37写道：
>
> Hi!
>
> On Mon, Nov 02, 2020 at 06:01:57PM +0800, Yu-Tung Chang wrote:
> > The NanoPi R1 is a complete open source board developed
> > by FriendlyElec for makers, hobbyists, fans and etc.
> >
> > NanoPi R1 key features
> > - Allwinner H3, Quad-core Cortex-A7 at 1.2GHz
> > - 512MB/1GB DDR3 RAM
> > - 8GB eMMC
> > - microSD slot
> > - 10/100/1000M Ethernet x 1
> > - 10/100 Ethernet x 1
> > - Wifi 802.11b/g/n
> > - Bluetooth 4.0
> > - Serial Debug Port
> > - 5V 2A DC power-supply
> >
> > Signed-off-by: Yu-Tung Chang <mtwget at gmail.com>
> > ---
> > .../devicetree/bindings/arm/sunxi.yaml | 5 +
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts | 169 ++++++++++++++++++
> > 3 files changed, 175 insertions(+)
> > create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
> >
> > diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
> > index 0f23133672a3..54a1aaee7e22 100644
> > --- a/Documentation/devicetree/bindings/arm/sunxi.yaml
> > +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
> > @@ -251,6 +251,11 @@ properties:
> > - const: friendlyarm,nanopi-neo-plus2
> > - const: allwinner,sun50i-h5
> >
> > + - description: FriendlyARM NanoPi R1
> > + items:
> > + - const: friendlyarm,nanopi-r1
> > + - const: allwinner,sun8i-h3
> > +
> > - description: FriendlyARM ZeroPi
> > items:
> > - const: friendlyarm,zeropi
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 4f0adfead547..aabaf67f86ed 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -1192,6 +1192,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
> > sun8i-h3-nanopi-m1-plus.dtb \
> > sun8i-h3-nanopi-neo.dtb \
> > sun8i-h3-nanopi-neo-air.dtb \
> > + sun8i-h3-nanopi-r1.dtb \
> > sun8i-h3-orangepi-2.dtb \
> > sun8i-h3-orangepi-lite.dtb \
> > sun8i-h3-orangepi-one.dtb \
> > diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
> > new file mode 100644
> > index 000000000000..204a39f93f4e
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
> > @@ -0,0 +1,169 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (C) 2019 Igor Pecovnik <igor at armbian.com>
> > + * Copyright (C) 2020 Jayantajit Gogoi <jayanta.gogoi525 at gmail.com>
> > + * Copyright (C) 2020 Yu-Tung Chang <mtwget at gmail.com>
> > +*/
> > +
> > +#include "sun8i-h3-nanopi.dtsi"
> > +#include <dt-bindings/leds/common.h>
> > +
> > +/ {
> > + model = "FriendlyARM NanoPi R1";
> > + compatible = "friendlyarm,nanopi-r1", "allwinner,sun8i-h3";
> > +
> > + aliases {
> > + serial1 = &uart1;
> > + ethernet0 = &emac;
> > + ethernet1 = &wifi;
> > + };
> > +
> > + reg_gmac_3v3: gmac-3v3 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "gmac-3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + startup-delay-us = <100000>;
> > + enable-active-high;
> > + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */
> > + };
> > +
> > + reg_vdd_cpux: gpio-regulator {
> > + compatible = "regulator-gpio";
> > + regulator-name = "vdd-cpux";
> > + regulator-type = "voltage";
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1300000>;
> > + regulator-ramp-delay = <50>;
> > + gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
> > + gpios-states = <0x1>;
> > + states = <1100000 0x0
> > + 1300000 0x1>;
> > + };
> > +
> > + wifi_pwrseq: wifi_pwrseq {
> > + compatible = "mmc-pwrseq-simple";
> > + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > + clocks = <&rtc 1>;
> > + clock-names = "ext_clock";
> > + };
> > +
> > + leds {
> > + led-2 {
> > + function = LED_FUNCTION_WAN;
> > + color = <LED_COLOR_ID_GREEN>;
> > + gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
> > + };
> > +
> > + led-3 {
> > + function = LED_FUNCTION_LAN;
> > + color = <LED_COLOR_ID_GREEN>;
> > + gpios = <&pio 0 9 GPIO_ACTIVE_HIGH>; /* PA9 */
> > + };
> > + };
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <®_vdd_cpux>;
> > +};
> > +
> > +&ehci1 {
> > + status = "okay";
> > +};
> > +
> > +&ehci2 {
> > + status = "okay";
> > +};
> > +
> > +&emac {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&emac_rgmii_pins>;
> > + phy-supply = <®_gmac_3v3>;
> > + phy-handle = <&ext_rgmii_phy>;
> > + phy-mode = "rgmii-id";
> > + status = "okay";
> > +};
> > +
> > +&external_mdio {
> > + ext_rgmii_phy: ethernet-phy at 7 {
> > + compatible = "ethernet-phy-ieee802.3-c22";
> > + reg = <7>;
> > + };
> > +};
> > +
> > +&mmc1 {
> > + vmmc-supply = <®_vcc3v3>;
> > + vqmmc-supply = <®_vcc3v3>;
> > + mmc-pwrseq = <&wifi_pwrseq>;
> > + bus-width = <4>;
> > + non-removable;
> > + status = "okay";
> > +
> > + wifi: wifi at 1 {
> > + reg = <1>;
> > + compatible = "brcm,bcm4329-fmac";
> > + interrupt-parent = <&pio>;
> > + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
> > + interrupt-names = "host-wake";
> > + };
> > +};
> > +
> > +&mmc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc2_8bit_pins>;
> > + vmmc-supply = <®_vcc3v3>;
> > + vqmmc-supply = <®_vcc3v3>;
> > + bus-width = <8>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&ohci1 {
> > + status = "okay";
> > +};
> > +
> > +&ohci2 {
> > + status = "okay";
> > +};
> > +
> > +®_usb0_vbus {
> > + gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart1_pins>;
>
> This should be already set in the DTSI
>
> > + status = "okay";
> > +};
>
> What is this UART used for?
>
> Thanks!
> Maxime
More information about the linux-arm-kernel
mailing list