[PATCH 1/5] arm64: dts: imx8mn: Enable Asynchronous Sample Rate Converter

[Adam Ford]

On Sat, Oct 31, 2020 at 9:03 PM Shawn Guo <shawnguo at kernel.org> wrote:
>
> On Mon, Oct 19, 2020 at 12:45:24PM -0500, Adam Ford wrote:
> > The driver exists for the Enhanced Asynchronous Sample Rate Converter
> > (EASRC) Controller, but there isn't a device tree entry for it.
> >
> > On the vendor kernel, they put this on a spba-bus for SDMA support.
> >
> > Add the the node for the spba-bus with the easrc node inside.
> >
> > Signed-off-by: Adam Ford <aford173 at gmail.com>
> >
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
> > index 746faf1cf2fb..7d34281332e1 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
> > @@ -246,6 +246,34 @@ aips1: bus at 30000000 {
> >                       #size-cells = <1>;
> >                       ranges;
> >
> > +                     spba-bus at 30000000 {
>
> spba: bus at 30000000

Go ahead and disregard my V2.  I'll submit a V3.  I sent the V2 before
I got this feedback.

>
> > +                             compatible = "fsl,spba-bus", "simple-bus";
>
> "fsl,spba-bus" is undocumented.  Document it or drop it.

I just submitted a patch to document this bus.  It's used on a bunch
of imx boards, so I think it's important to document it.
I assigned you as the maintainer of the binding doc since you're
listed as the maintainer of the SDMA driver which is what's using
the compatible flag.  I hope that is the correct thing to do.

>
> > +                             #address-cells = <1>;
> > +                             #size-cells = <1>;
> > +                             reg = <0x30000000 0x100000>;
> > +                             ranges;
> > +
> > +                             easrc: easrc at 300C0000 {
> > +                                     compatible = "fsl,imx8mn-easrc";
> > +                                     reg = <0x300C0000 0x10000>;
> > +                                     interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
> > +                                     clocks = <&clk IMX8MN_CLK_ASRC_ROOT>;
> > +                                     clock-names = "mem";
> > +                                     dmas = <&sdma2 16 23 0> , <&sdma2 17 23 0>,
> > +                                            <&sdma2 18 23 0> , <&sdma2 19 23 0>,
> > +                                            <&sdma2 20 23 0> , <&sdma2 21 23 0>,
> > +                                            <&sdma2 22 23 0> , <&sdma2 23 23 0>;
> > +                                     dma-names = "ctx0_rx", "ctx0_tx",
> > +                                                 "ctx1_rx", "ctx1_tx",
> > +                                                 "ctx2_rx", "ctx2_tx",
> > +                                                 "ctx3_rx", "ctx3_tx";
> > +                                     fsl,easrc-ram-script-name = "imx/easrc/easrc-imx8mn.bin";
>
> Undocumented property?

That's my fault.  I accidentally copied the device tree entry from the
vendor kernel instead of using the naming from the device tree binding
document.
I fixed this in my V2, but I need to send a V3 anyway.

adam

>
> Shawn
>
> > +                                     fsl,asrc-rate  = <8000>;
> > +                                     fsl,asrc-width = <16>;
> > +                                     status = "disabled";
> > +                             };
> > +                     };
> > +
> >                       gpio1: gpio at 30200000 {
> >                               compatible = "fsl,imx8mn-gpio", "fsl,imx35-gpio";
> >                               reg = <0x30200000 0x10000>;
> > --
> > 2.25.1
> >