[PATCH v5 09/13] drm/panel: st7703: Add support for Xingbangda XBD599

Ondrej Jirman megous at megous.com
Thu Jun 25 20:55:57 EDT 2020


Xingbangda XBD599 is a 5.99" 720x1440 MIPI-DSI LCD panel used in
PinePhone. Add support for it.

Signed-off-by: Icenowy Zheng <icenowy at aosc.io>
Signed-off-by: Ondrej Jirman <megous at megous.com>
---
 drivers/gpu/drm/panel/panel-sitronix-st7703.c | 199 +++++++++++++++++-
 1 file changed, 197 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7703.c b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
index cdbf7dfb4dd4..33611419059a 100644
--- a/drivers/gpu/drm/panel/panel-sitronix-st7703.c
+++ b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
@@ -39,10 +39,11 @@
 #define ST7703_CMD_SETEXTC	 0xB9
 #define ST7703_CMD_SETMIPI	 0xBA
 #define ST7703_CMD_SETVDC	 0xBC
-#define ST7703_CMD_UNKNOWN0	 0xBF
+#define ST7703_CMD_UNKNOWN_BF	 0xBF
 #define ST7703_CMD_SETSCR	 0xC0
 #define ST7703_CMD_SETPOWER	 0xC1
 #define ST7703_CMD_SETPANEL	 0xCC
+#define ST7703_CMD_UNKNOWN_C6	 0xC6
 #define ST7703_CMD_SETGAMMA	 0xE0
 #define ST7703_CMD_SETEQ	 0xE3
 #define ST7703_CMD_SETGIP1	 0xE9
@@ -109,7 +110,7 @@ static int jh057n_init_sequence(struct st7703 *ctx)
 	msleep(20);
 
 	dsi_generic_write_seq(dsi, ST7703_CMD_SETVCOM, 0x3F, 0x3F);
-	dsi_generic_write_seq(dsi, ST7703_CMD_UNKNOWN0, 0x02, 0x11, 0x00);
+	dsi_generic_write_seq(dsi, ST7703_CMD_UNKNOWN_BF, 0x02, 0x11, 0x00);
 	dsi_generic_write_seq(dsi, ST7703_CMD_SETGIP1,
 			      0x82, 0x10, 0x06, 0x05, 0x9E, 0x0A, 0xA5, 0x12,
 			      0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38,
@@ -163,6 +164,199 @@ struct st7703_panel_desc jh057n00900_panel_desc = {
 	.init_sequence = jh057n_init_sequence,
 };
 
+#define dsi_dcs_write_seq(dsi, cmd, seq...) do {			\
+		static const u8 d[] = { seq };				\
+		int ret;						\
+		ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d));	\
+		if (ret < 0)						\
+			return ret;					\
+	} while (0)
+
+
+static int xbd599_init_sequence(struct st7703 *ctx)
+{
+	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+
+	/*
+	 * Init sequence was supplied by the panel vendor.
+	 */
+
+	/* Magic sequence to unlock user commands below. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETEXTC, 0xF1, 0x12, 0x83);
+
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETMIPI,
+			  0x33, /* VC_main = 0, Lane_Number = 3 (4 lanes) */
+			  0x81, /* DSI_LDO_SEL = 1.7V, RTERM = 90 Ohm */
+			  0x05, /* IHSRX = x6 (Low High Speed driving ability) */
+			  0xF9, /* TX_CLK_SEL = fDSICLK/16 */
+			  0x0E, /* HFP_OSC (min. HFP number in DSI mode) */
+			  0x0E, /* HBP_OSC (min. HBP number in DSI mode) */
+			  /* The rest is undocumented in ST7703 datasheet */
+			  0x20, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+			  0x44, 0x25, 0x00, 0x91, 0x0a, 0x00, 0x00, 0x02,
+			  0x4F, 0x11, 0x00, 0x00, 0x37);
+
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER_EXT,
+			  0x25, /* PCCS = 2, ECP_DC_DIV = 1/4 HSYNC */
+			  0x22, /* DT = 15ms XDK_ECP = x2 */
+			  0x20, /* PFM_DC_DIV = /1 */
+			  0x03  /* ECP_SYNC_EN = 1, VGX_SYNC_EN = 1 */);
+
+	/* RGB I/F porch timing */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETRGBIF,
+			  0x10, /* VBP_RGB_GEN */
+			  0x10, /* VFP_RGB_GEN */
+			  0x05, /* DE_BP_RGB_GEN */
+			  0x05, /* DE_FP_RGB_GEN */
+			  /* The rest is undocumented in ST7703 datasheet */
+			  0x03, 0xFF,
+			  0x00, 0x00,
+			  0x00, 0x00);
+
+	/* Source driving settings. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETSCR,
+			  0x73, /* N_POPON */
+			  0x73, /* N_NOPON */
+			  0x50, /* I_POPON */
+			  0x50, /* I_NOPON */
+			  0x00, /* SCR[31,24] */
+			  0xC0, /* SCR[23,16] */
+			  0x08, /* SCR[15,8] */
+			  0x70, /* SCR[7,0] */
+			  0x00  /* Undocumented */);
+
+	/* NVDDD_SEL = -1.8V, VDDD_SEL = out of range (possibly 1.9V?) */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETVDC, 0x4E);
+
+	/*
+	 * SS_PANEL = 1 (reverse scan), GS_PANEL = 0 (normal scan)
+	 * REV_PANEL = 1 (normally black panel), BGR_PANEL = 1 (BGR)
+	 */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPANEL, 0x0B);
+
+	/* Zig-Zag Type C column inversion. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETCYC, 0x80);
+
+	/* Set display resolution. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETDISP,
+			  0xF0, /* NL = 240 */
+			  0x12, /* RES_V_LSB = 0, BLK_CON = VSSD,
+				 * RESO_SEL = 720RGB
+				 */
+			  0xF0  /* WHITE_GND_EN = 1 (GND),
+				 * WHITE_FRAME_SEL = 7 frames,
+				 * ISC = 0 frames
+				 */);
+
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETEQ,
+			  0x00, /* PNOEQ */
+			  0x00, /* NNOEQ */
+			  0x0B, /* PEQGND */
+			  0x0B, /* NEQGND */
+			  0x10, /* PEQVCI */
+			  0x10, /* NEQVCI */
+			  0x00, /* PEQVCI1 */
+			  0x00, /* NEQVCI1 */
+			  0x00, /* reserved */
+			  0x00, /* reserved */
+			  0xFF, /* reserved */
+			  0x00, /* reserved */
+			  0xC0, /* ESD_DET_DATA_WHITE = 1, ESD_WHITE_EN = 1 */
+			  0x10  /* SLPIN_OPTION = 1 (no need vsync after sleep-in)
+				 * VEDIO_NO_CHECK_EN = 0
+				 * ESD_WHITE_GND_EN = 0
+				 * ESD_DET_TIME_SEL = 0 frames
+				 */);
+
+	/* Undocumented command. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_C6, 0x01, 0x00, 0xFF, 0xFF, 0x00);
+
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER,
+			  0x74, /* VBTHS, VBTLS: VGH = 17V, VBL = -11V */
+			  0x00, /* FBOFF_VGH = 0, FBOFF_VGL = 0 */
+			  0x32, /* VRP  */
+			  0x32, /* VRN */
+			  0x77, /* reserved */
+			  0xF1, /* APS = 1 (small),
+				 * VGL_DET_EN = 1, VGH_DET_EN = 1,
+				 * VGL_TURBO = 1, VGH_TURBO = 1
+				 */
+			  0xFF, /* VGH1_L_DIV, VGL1_L_DIV (1.5MHz) */
+			  0xFF, /* VGH1_R_DIV, VGL1_R_DIV (1.5MHz) */
+			  0xCC, /* VGH2_L_DIV, VGL2_L_DIV (2.6MHz) */
+			  0xCC, /* VGH2_R_DIV, VGL2_R_DIV (2.6MHz) */
+			  0x77, /* VGH3_L_DIV, VGL3_L_DIV (4.5MHz) */
+			  0x77  /* VGH3_R_DIV, VGL3_R_DIV (4.5MHz) */);
+
+	/* Reference voltage. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETBGP,
+			  0x07, /* VREF_SEL = 4.2V */
+			  0x07  /* NVREF_SEL = 4.2V */);
+
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETVCOM,
+			  0x2C, /* VCOMDC_F = -0.67V */
+			  0x2C  /* VCOMDC_B = -0.67V */);
+
+	/* Undocumented command. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_BF, 0x02, 0x11, 0x00);
+
+	/* This command is to set forward GIP timing. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP1,
+			  0x82, 0x10, 0x06, 0x05, 0xA2, 0x0A, 0xA5, 0x12,
+			  0x31, 0x23, 0x37, 0x83, 0x04, 0xBC, 0x27, 0x38,
+			  0x0C, 0x00, 0x03, 0x00, 0x00, 0x00, 0x0C, 0x00,
+			  0x03, 0x00, 0x00, 0x00, 0x75, 0x75, 0x31, 0x88,
+			  0x88, 0x88, 0x88, 0x88, 0x88, 0x13, 0x88, 0x64,
+			  0x64, 0x20, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
+			  0x02, 0x88, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00);
+
+	/* This command is to set backward GIP timing. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP2,
+			  0x02, 0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+			  0x00, 0x00, 0x00, 0x00, 0x02, 0x46, 0x02, 0x88,
+			  0x88, 0x88, 0x88, 0x88, 0x88, 0x64, 0x88, 0x13,
+			  0x57, 0x13, 0x88, 0x88, 0x88, 0x88, 0x88, 0x88,
+			  0x75, 0x88, 0x23, 0x14, 0x00, 0x00, 0x02, 0x00,
+			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+			  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x03, 0x0A,
+			  0xA5, 0x00, 0x00, 0x00, 0x00);
+
+	/* Adjust the gamma characteristics of the panel. */
+	dsi_dcs_write_seq(dsi, ST7703_CMD_SETGAMMA,
+			  0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41, 0x35,
+			  0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12, 0x12,
+			  0x18, 0x00, 0x09, 0x0D, 0x23, 0x27, 0x3C, 0x41,
+			  0x35, 0x07, 0x0D, 0x0E, 0x12, 0x13, 0x10, 0x12,
+			  0x12, 0x18);
+
+	return 0;
+}
+
+static const struct drm_display_mode xbd599_mode = {
+	.hdisplay    = 720,
+	.hsync_start = 720 + 40,
+	.hsync_end   = 720 + 40 + 40,
+	.htotal	     = 720 + 40 + 40 + 40,
+	.vdisplay    = 1440,
+	.vsync_start = 1440 + 18,
+	.vsync_end   = 1440 + 18 + 10,
+	.vtotal	     = 1440 + 18 + 10 + 17,
+	.vrefresh    = 60,
+	.clock	     = 69000,
+	.flags	     = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+	.width_mm    = 68,
+	.height_mm   = 136,
+};
+
+static const struct st7703_panel_desc xbd599_desc = {
+	.mode = &xbd599_mode,
+	.lanes = 4,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE,
+	.format = MIPI_DSI_FMT_RGB888,
+	.init_sequence = xbd599_init_sequence,
+};
+
 static int st7703_enable(struct drm_panel *panel)
 {
 	struct st7703 *ctx = panel_to_st7703(panel);
@@ -428,6 +622,7 @@ static int st7703_remove(struct mipi_dsi_device *dsi)
 
 static const struct of_device_id st7703_of_match[] = {
 	{ .compatible = "rocktech,jh057n00900", .data = &jh057n00900_panel_desc },
+	{ .compatible = "xingbangda,xbd599", .data = &xbd599_desc },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, st7703_of_match);
-- 
2.27.0




More information about the linux-arm-kernel mailing list