[PATCH 5/6] arm64: dts: qcom: sm8250: Add remoteprocs

[Manivannan Sadhasivam]

On Mon, Jun 22, 2020 at 03:27:46PM -0700, Bjorn Andersson wrote:
> Add remoteproc nodes for the audio, compute and sensor cores, define
> glink for each one and enable them on the MTP with appropriate firmware
> defined.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson at linaro.org>

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>

Thanks,
Mani

> ---
>  arch/arm64/boot/dts/qcom/sm8250-mtp.dts |  15 +++
>  arch/arm64/boot/dts/qcom/sm8250.dtsi    | 116 ++++++++++++++++++++++++
>  2 files changed, 131 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
> index 63d259931c4d..6894f8490dae 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
> @@ -55,6 +55,11 @@ vreg_s6c_0p88: smpc6-regulator {
>  	};
>  };
>  
> +&adsp {
> +	status = "okay";
> +	firmware-name = "qcom/sm8250/adsp.mbn";
> +};
> +
>  &apps_rsc {
>  	pm8150-rpmh-regulators {
>  		compatible = "qcom,pm8150-rpmh-regulators";
> @@ -348,10 +353,20 @@ vreg_l7f_1p8: ldo7 {
>  	};
>  };
>  
> +&cdsp {
> +	status = "okay";
> +	firmware-name = "qcom/sm8250/cdsp.mbn";
> +};
> +
>  &qupv3_id_1 {
>  	status = "okay";
>  };
>  
> +&slpi {
> +	status = "okay";
> +	firmware-name = "qcom/sm8250/slpi.mbn";
> +};
> +
>  &tlmm {
>  	gpio-reserved-ranges = <28 4>, <40 4>;
>  };
> diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> index 364d9a798673..a21299b9c62f 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> @@ -1052,6 +1052,83 @@ tcsr_mutex_regs: syscon at 1f40000 {
>  			reg = <0x0 0x01f40000 0x0 0x40000>;
>  		};
>  
> +		slpi: remoteproc at 5c00000 {
> +			compatible = "qcom,sm8250-slpi-pas";
> +			reg = <0 0x05c00000 0 0x4000>;
> +
> +			interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "wdog", "fatal", "ready",
> +					  "handover", "stop-ack";
> +
> +			clocks = <&rpmhcc RPMH_CXO_CLK>;
> +			clock-names = "xo";
> +
> +			power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>,
> +					<&rpmhpd SM8250_LCX>,
> +					<&rpmhpd SM8250_LMX>;
> +			power-domain-names = "load_state", "lcx", "lmx";
> +
> +			memory-region = <&slpi_mem>;
> +
> +			qcom,smem-states = <&smp2p_slpi_out 0>;
> +			qcom,smem-state-names = "stop";
> +
> +			status = "disabled";
> +
> +			glink-edge {
> +				interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
> +							     IPCC_MPROC_SIGNAL_GLINK_QMP
> +							     IRQ_TYPE_EDGE_RISING>;
> +				mboxes = <&ipcc IPCC_CLIENT_SLPI
> +						IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> +				label = "lpass";
> +				qcom,remote-pid = <3>;
> +			};
> +		};
> +
> +		cdsp: remoteproc at 8300000 {
> +			compatible = "qcom,sm8250-cdsp-pas";
> +			reg = <0 0x08300000 0 0x10000>;
> +
> +			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "wdog", "fatal", "ready",
> +					  "handover", "stop-ack";
> +
> +			clocks = <&rpmhcc RPMH_CXO_CLK>;
> +			clock-names = "xo";
> +
> +			power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>,
> +					<&rpmhpd SM8250_CX>;
> +			power-domain-names = "load_state", "cx";
> +
> +			memory-region = <&cdsp_mem>;
> +
> +			qcom,smem-states = <&smp2p_cdsp_out 0>;
> +			qcom,smem-state-names = "stop";
> +
> +			status = "disabled";
> +
> +			glink-edge {
> +				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
> +							     IPCC_MPROC_SIGNAL_GLINK_QMP
> +							     IRQ_TYPE_EDGE_RISING>;
> +				mboxes = <&ipcc IPCC_CLIENT_CDSP
> +						IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> +				label = "lpass";
> +				qcom,remote-pid = <5>;
> +			};
> +		};
> +
>  		pdc: interrupt-controller at b220000 {
>  			compatible = "qcom,sm8250-pdc", "qcom,pdc";
>  			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
> @@ -1668,6 +1745,45 @@ config {
>  			};
>  		};
>  
> +		adsp: remoteproc at 17300000 {
> +			compatible = "qcom,sm8250-adsp-pas";
> +			reg = <0 0x17300000 0 0x100>;
> +
> +			interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "wdog", "fatal", "ready",
> +					  "handover", "stop-ack";
> +
> +			clocks = <&rpmhcc RPMH_CXO_CLK>;
> +			clock-names = "xo";
> +
> +			power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>,
> +					<&rpmhpd SM8250_LCX>,
> +					<&rpmhpd SM8250_LMX>;
> +			power-domain-names = "load_state", "lcx", "lmx";
> +
> +			memory-region = <&adsp_mem>;
> +
> +			qcom,smem-states = <&smp2p_adsp_out 0>;
> +			qcom,smem-state-names = "stop";
> +
> +			status = "disabled";
> +
> +			glink-edge {
> +				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
> +							     IPCC_MPROC_SIGNAL_GLINK_QMP
> +							     IRQ_TYPE_EDGE_RISING>;
> +				mboxes = <&ipcc IPCC_CLIENT_LPASS
> +						IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> +				label = "lpass";
> +				qcom,remote-pid = <2>;
> +			};
> +		};
> +
>  		intc: interrupt-controller at 17a00000 {
>  			compatible = "arm,gic-v3";
>  			#interrupt-cells = <3>;
> -- 
> 2.26.2
>