[RESEND PATCH v4 0/7] Convert mtk-dsi to drm_bridge API and get EDID for ps8640 bridge

[Sam Ravnborg]

Hi Enric

On Mon, Jun 15, 2020 at 10:31:01PM +0200, Enric Balletbo i Serra wrote:
> (This resend is to fix some trivial conflicts due the merge window)
> 
> The PS8640 dsi-to-eDP bridge driver is using the panel bridge API,
> however, not all the components in the chain have been ported to the
> drm_bridge API. Actually, when a panel is attached the default panel's mode
> is used, but in some cases we can't get display up if mode getting from
> eDP control EDID is not chosen.
> 
> This series address that problem, first implements the .get_edid()
> callback in the PS8640 driver (which is not used until the conversion is
> done) and then, converts the Mediatek DSI driver to use the drm_bridge
> API.
> 
> As far as I know, we're the only users of the mediatek dsi driver in
> mainline, so should be safe to switch to the new chain of drm_bridge API
> unconditionally.
> 
> The patches has been tested on a Acer Chromebook R13 (Elm) running a
> Chrome OS userspace and checking that the valid EDID mode reported by
> the bridge is selected.
> 
> Changes in v4:
> - Remove double call to drm_encoder_init(). (Chun-Kuang Hu)
> - Cleanup the encoder in mtk_dsi_unbind(). (Chun-Kuang Hu)
> 
> Changes in v3:
> - Replace s/bridge/next bridge/ for comment. (Laurent Pinchart)
> - Add the bridge.type. (Laurent Pinchart)
> - Use next_bridge field to store the panel bridge. (Laurent Pinchart)
> - Add the bridge.type field. (Laurent Pinchart)
> - This patch requires https://lkml.org/lkml/2020/4/16/2080 to work
>   properly.
> - Move the bridge.type line to the patch that adds drm_bridge support. (Laurent Pinchart)
> 
> Changes in v2:
> - Do not set connector_type for panel here. (Sam Ravnborg)
> 
> Enric Balletbo i Serra (7):
>   drm/bridge: ps8640: Get the EDID from eDP control
>   drm/bridge_connector: Set default status connected for eDP connectors
>   drm/mediatek: mtk_dsi: Rename bridge to next_bridge
>   drm/mediatek: mtk_dsi: Convert to bridge driver
>   drm/mediatek: mtk_dsi: Use simple encoder
>   drm/mediatek: mtk_dsi: Use the drm_panel_bridge API
>   drm/mediatek: mtk_dsi: Create connector for bridges

Patch seems ready to apply. Will they be applied to a mediatek tree
or to drm-misc-next?
Or shall we take the first two patches via drm-misc-next, and the
remaning via a mediatek tree? (I hope not)

	Sam


> 
>  drivers/gpu/drm/bridge/parade-ps8640.c |  12 ++
>  drivers/gpu/drm/drm_bridge_connector.c |   1 +
>  drivers/gpu/drm/mediatek/mtk_dsi.c     | 269 ++++++++-----------------
>  3 files changed, 97 insertions(+), 185 deletions(-)
> 
> -- 
> 2.27.0
> 
> _______________________________________________
> dri-devel mailing list
> dri-devel at lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel