[PATCH v4 1/5] dt-bindings: irqchip: Add PRU-ICSS interrupt controller bindings
Rob Herring
robh at kernel.org
Fri Jul 31 17:09:09 EDT 2020
On Fri, Jul 31, 2020 at 01:48:57PM +0200, Grzegorz Jaszczyk wrote:
> On Wed, 29 Jul 2020 at 19:34, David Lechner <david at lechnology.com> wrote:
> >
> > On 7/28/20 4:18 AM, Grzegorz Jaszczyk wrote:
> > > From: Suman Anna <s-anna at ti.com>
> > >
> > > The Programmable Real-Time Unit and Industrial Communication Subsystem
> > > (PRU-ICSS or simply PRUSS) contains an interrupt controller (INTC) that
> > > can handle various system input events and post interrupts back to the
> > > device-level initiators. The INTC can support upto 64 input events on
> >
> > nit: "up to" is two separate words
>
> Ok.
>
> >
> > > most SoCs with individual control configuration and h/w prioritization.
> > > These events are mapped onto 10 output interrupt lines through two levels
> > > of many-to-one mapping support. Different interrupt lines are routed to
> > > the individual PRU cores or to the host CPU or to other PRUSS instances.
> > >
> > > The K3 AM65x and J721E SoCs have the next generation of the PRU-ICSS IP,
> > > commonly called ICSSG. The ICSSG interrupt controller on K3 SoCs provide
> > > a higher number of host interrupts (20 vs 10) and can handle an increased
> > > number of input events (160 vs 64) from various SoC interrupt sources.
> > >
> > > Add the bindings document for these interrupt controllers on all the
> > > applicable SoCs. It covers the OMAP architecture SoCs - AM33xx, AM437x
> > > and AM57xx; the Keystone 2 architecture based 66AK2G SoC; the Davinci
> > > architecture based OMAPL138 SoCs, and the K3 architecture based AM65x
> > > and J721E SoCs.
> > >
> > > Signed-off-by: Suman Anna <s-anna at ti.com>
> > > Signed-off-by: Andrew F. Davis <afd at ti.com>
> > > Signed-off-by: Roger Quadros <rogerq at ti.com>
> > > Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk at linaro.org>
> > > ---
> > > v3->v4:
> > > - Drop allOf references to interrupt-controller.yaml and
> > > interrupts.yaml.
> > > - Drop items descriptions and use only maxItems: 1 as suggested by Rob.
> > > - Convert irqs-reserved property from uint8-array to bitmask.
> > > - Minor descriptions updates.
> > > - Change interrupt-cells to 3 in order to provide 2-level mapping
> > > description for interrupts routed to the main CPU (as Marc requested).
> > > - Merge the irqs-reserved and irqs-shared to one property since they
> > > can be handled by one logic.
> > > - Drop reviewed-by due to introduced changes.
> > > - Add another example illustrating irqs-reserved property usage.
> > > v2->v3:
> > > - Convert dt-binding to YAML
> > > v1->v2:
> > > - https://patchwork.kernel.org/patch/11069767/
> > > ---
> > > .../interrupt-controller/ti,pruss-intc.yaml | 157 +++++++++++++++++++++
> > > 1 file changed, 157 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml b/Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml
> > > new file mode 100644
> > > index 0000000..7336b11
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml
> > > @@ -0,0 +1,157 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/interrupt-controller/ti,pruss-intc.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: TI PRU-ICSS Local Interrupt Controller
> > > +
> > > +maintainers:
> > > + - Suman Anna <s-anna at ti.com>
> > > +
> > > +description: |
> > > + Each PRU-ICSS has a single interrupt controller instance that is common
> > > + to all the PRU cores. Most interrupt controllers can route 64 input events
> > > + which are then mapped to 10 possible output interrupts through two levels
> > > + of mapping. The input events can be triggered by either the PRUs and/or
> > > + various other PRUSS internal and external peripherals. The first 2 output
> > > + interrupts (0, 1) are fed exclusively to the internal PRU cores, with the
> > > + remaining 8 (2 through 9) connected to external interrupt controllers
> > > + including the MPU and/or other PRUSS instances, DSPs or devices.
> > > +
> > > + The property "ti,irqs-reserved" is used for denoting the connection
> > > + differences on the output interrupts 2 through 9. If this property is not
> > > + defined, it implies that all the PRUSS INTC output interrupts 2 through 9
> > > + (host_intr0 through host_intr7) are connected exclusively to the Arm interrupt
> > > + controller.
> > > +
> > > + The K3 family of SoCs can handle 160 input events that can be mapped to 20
> > > + different possible output interrupts. The additional output interrupts (10
> > > + through 19) are connected to new sub-modules within the ICSSG instances.
> > > +
> > > + This interrupt-controller node should be defined as a child node of the
> > > + corresponding PRUSS node. The node should be named "interrupt-controller".
> > > +
> > > +properties:
> > > + compatible:
> > > + enum:
> > > + - ti,pruss-intc
> > > + - ti,icssg-intc
> > > + description: |
> > > + Use "ti,pruss-intc" for OMAP-L13x/AM18x/DA850 SoCs,
> > > + AM335x family of SoCs,
> > > + AM437x family of SoCs,
> > > + AM57xx family of SoCs
> > > + 66AK2G family of SoCs
> > > + Use "ti,icssg-intc" for K3 AM65x & J721E family of SoCs
> > > +
> > > + reg:
> > > + maxItems: 1
> > > +
> > > + interrupts:
> > > + minItems: 1
> > > + maxItems: 8
> > > + description: |
> > > + All the interrupts generated towards the main host processor in the SoC.
> > > + A shared interrupt can be skipped if the desired destination and usage is
> > > + by a different processor/device.
> >
> > This sounds like using device tree for configuration. Also, isn't this what the
> > ti,irqs-reserved property is for?
>
> Yes this is what ti,irqs-reserved is also used for. The intention was
> to keep both in sync, so it would be less confusing: if some
> interrupts are on irqs-reserved list, they shouldn't be present here.
> In terms of shared interrupt usage I will not call it configuration
> via device-tree, rather design description (for single device tree
> description given shared interrupt is used or as MCPU one or as
> different processor/device one).
>
> >
> > > +
> > > + interrupt-names:
> > > + minItems: 1
> > > + maxItems: 8
> > > + items:
> > > + pattern: host_intr[0-7]
> > > + description: |
> > > + Should use one of the above names for each valid host event interrupt
> > > + connected to Arm interrupt controller, the name should match the
> > > + corresponding host event interrupt number.
> > > +
> > > + interrupt-controller: true
> > > +
> > > + "#interrupt-cells":
> > > + const: 3
> > > + description: |
> > > + Client users shall use the PRU System event number (the interrupt source
> > > + that the client is interested in), PRU channel and PRU host_intr (target)
> > > + as the value of the interrupts property in their node. The system events
> > > + can be mapped to some output host interrupts through 2 levels of
> > > + many-to-one mapping i.e. events to channel mapping and channels to host
> > > + interrupts so through this property entire mapping is provided.
> >
> > It is not clear what the meaning of each cell is. Looking at later patches, it
> > looks like the first cell is the PRU system event number, the second cell is the
> > channel and the third cell is the host event number.
>
> Ok, how about updating above description like this:
> Client users shall use the PRU System event number (the interrupt source
> that the client is interested in) [cell 1], PRU channel [cell 2] and PRU
> host_intr (target) [cell 3] as the value of the interrupts property in their
> node. The system events can be mapped to some output host interrupts through 2
> levels of many-to-one mapping i.e. events to channel mapping and channels to
> host interrupts so through this property entire mapping is provided.
>
> >
> > > +
> > > + ti,irqs-reserved:
> > > + $ref: /schemas/types.yaml#definitions/uint8
> >
> > Is 8 bits enough for any possible future devices? It is written above that there are
> > already up to 20 host events on some devices even if only 8 are connected to the MCU.
>
> We've already discussed this with Suman: it is unlikely that HW with
> more than 8 host interrupts connected to the MCU will arrive.
>
> >
> > > + description: |
> > > + Bitmask of host interrupts between 0 and 7 (corresponding to PRUSS INTC
> > > + output interrupts 2 through 9) that are not connected to the Arm interrupt
> > > + controller or are shared and used by other devices or processors in the
> > > + SoC. Define this property when any of 8 interrupts should not be handled
> > > + by Arm interrupt controller.
> > > + Eg: - AM437x and 66AK2G SoCs do not have "host_intr5" interrupt
> > > + connected to MPU
> > > + - AM65x and J721E SoCs have "host_intr5", "host_intr6" and
> > > + "host_intr7" interrupts connected to MPU, and other ICSSG
> > > + instances.
> > > +
> > > +required:
> > > + - compatible
> > > + - reg
> > > + - interrupts
> > > + - interrupt-names
> > > + - interrupt-controller
> > > + - "#interrupt-cells"
> > > +
> > > +additionalProperties: false
> > > +
> > > +examples:
> > > + - |
> > > + /* AM33xx PRU-ICSS */
> > > + pruss: pruss at 0 {
> > > + compatible = "ti,am3356-pruss";
> > > + reg = <0x0 0x80000>;
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > + ranges;
> > > +
> > > + pruss_intc: interrupt-controller at 20000 {
> > > + compatible = "ti,pruss-intc";
> > > + reg = <0x20000 0x2000>;
> > > + interrupts = <20 21 22 23 24 25 26 27>;
> > > + interrupt-names = "host_intr0", "host_intr1",
> > > + "host_intr2", "host_intr3",
> > > + "host_intr4", "host_intr5",
> > > + "host_intr6", "host_intr7";
> > > + interrupt-controller;
> > > + #interrupt-cells = <3>;
> > > + };
> > > + };
> > > +
> > > + - |
> > > +
> > > + /* AM4376 PRU-ICSS */
> > > + #include <dt-bindings/interrupt-controller/arm-gic.h>
> > > + pruss at 0 {
> > > + compatible = "ti,am4376-pruss";
> > > + reg = <0x0 0x40000>;
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > + ranges;
> > > +
> > > + interrupt-controller at 20000 {
> > > + compatible = "ti,pruss-intc";
> > > + reg = <0x20000 0x2000>;
> > > + interrupt-controller;
> > > + #interrupt-cells = <3>;
> > > + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
> > > + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> > > + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
> > > + <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
> > > + <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
> > > + <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
> > > + <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
> > > + interrupt-names = "host_intr0", "host_intr1",
> > > + "host_intr2", "host_intr3",
> > > + "host_intr4",
> > > + "host_intr6", "host_intr7";
> > > + ti,irqs-reserved = /bits/ 8 <0x20>; /* BIT(5) */
> >
> > Is 0b00100000 valid syntax in device tree (instead of 0x20 + comment)?
Using binary? No.
> Actually I think more readable will be to define and use BIT()
> directly. Similar to what is done for one of the omap dtsi:
> https://elixir.bootlin.com/linux/latest/source/arch/arm/boot/dts/omap3-gta04.dtsi#L648
No, please don't add/use BIT(). I'd assume the common case here is not
only 1 bit set. Even if it is here, it's not in general, and I just
don't want more macros.
Rob
More information about the linux-arm-kernel
mailing list