[PATCH V3 3/3] pci: imx: Select RESET_IMX7 by default

[Anson Huang]

Hi, Philipp


> Subject: Re: [PATCH V3 3/3] pci: imx: Select RESET_IMX7 by default
> 
> Hi Anson,
> 
> On Thu, 2020-07-30 at 02:11 +0000, Anson Huang wrote:
> > Hi, Philipp/Rob
> >
> > > Subject: Re: [PATCH V3 3/3] pci: imx: Select RESET_IMX7 by default
> > >
> > > On Wed, 2020-07-29 at 09:26 -0600, Rob Herring wrote:
> > > > On Mon, Jul 20, 2020 at 8:26 AM Anson Huang
> <Anson.Huang at nxp.com>
> > > wrote:
> > > > > i.MX7 reset driver now supports module build and it is no longer
> > > > > built in by default, so i.MX PCI driver needs to select it
> > > > > explicitly due to it is NOT supporting loadable module currently.
> > > > >
> > > > > Signed-off-by: Anson Huang <Anson.Huang at nxp.com>
> > > > > ---
> > > > > No change.
> > > > > ---
> > > > >  drivers/pci/controller/dwc/Kconfig | 1 +
> > > > >  1 file changed, 1 insertion(+)
> > > > >
> > > > > diff --git a/drivers/pci/controller/dwc/Kconfig
> > > > > b/drivers/pci/controller/dwc/Kconfig
> > > > > index 044a376..bcf63ce 100644
> > > > > --- a/drivers/pci/controller/dwc/Kconfig
> > > > > +++ b/drivers/pci/controller/dwc/Kconfig
> > > > > @@ -90,6 +90,7 @@ config PCI_EXYNOS
> > > > >
> > > > >  config PCI_IMX6
> > > > >         bool "Freescale i.MX6/7/8 PCIe controller"
> > > > > +       select RESET_IMX7
> > > >
> > > > This will break as select will not cause all of RESET_IMX7's
> > > > dependencies to be met. It also doesn't scale. Are you going to do
> > > > the same thing for clocks, pinctrl, gpio, etc.?
> > > >
> > > > You should make the PCI driver work as a module.
> > >
> > > Oh, also PCI_IMX6 is used on (surprise) i.MX6, which doesn't need
> > > RESET_IMX7 at all.
> > >
> > > How about hiding the RESET_IMX7 option and setting it default y if
> > > PCI_IMX6 is enabled, as an interim solution?
> >
> > Like below, RESET_IMX7 is already default y when SOC_IMX7D, now added
> > PCI_IMX6, let me know if it is OK for you, then I will send new patch for
> review.
> >
> > +++ b/drivers/reset/Kconfig
> > @@ -68,7 +68,7 @@ config RESET_IMX7
> >         tristate "i.MX7/8 Reset Driver"
> 
> I was thinking something like
> 
> 	tristate "i.MX7/8 Reset Driver" if COMPILE_TEST || !PCI_IMX6
> 
> >         depends on HAS_IOMEM
> >         depends on SOC_IMX7D || (ARM64 && ARCH_MXC) ||
> COMPILE_TEST
> > -       default y if SOC_IMX7D
> > +       default y if (SOC_IMX7D || PCI_IMX6)
> 
> Yes, although without the above I think it could still be disabled manually or
> via oldconfig.

Then should I send a new version with below? As we already did it this way for i.MX7D,
adding it for i.MX6 makes more sense?

+       default y if (SOC_IMX7D || PCI_IMX6)

Thanks,
Anson