[PATCH 0/4] arm64: Initial support for Texas Instrument's J7200 Platform

[Grygorii Strashko]

On 23/07/2020 11:46, Lokesh Vutla wrote:
> This series adds initial support for latest new SoC, J7200, from Texas Instruments.
> 
> The J7200 SoC is a part of the K3 Multicore SoC architecture platform.
> It is targeted for for automotive gateway, vehicle compute systems,
> Vehicle-to-Vehicle (V2V) and Vehicle-to-Everything (V2X) applications.
> The SoC aims to meet the complex processing needs of modern embedded products.
> 
> See J7200 Technical Reference Manual (SPRUIU1, June 2020)
> for further details: https://www.ti.com/lit/pdf/spruiu1
> 
> Testing:
> - Boot log: https://pastebin.ubuntu.com/p/FvpzWjf7tw/
> - ./scripts/checkpatch --strict
> 	- Few warningns about Line length exceeding 100 columns.
> 	  But these are corresponding to comments
> - v8make dtbs_check
> - DT_SCHEMA_FLAGS="-u"
>    DT_SCHEMA_FILES="Documentation/devicetree/bindings/arm/ti/k3.yaml"
>    v8make dtbs_check
> - DT_SCHEMA_FLAGS="-u"
>    DT_SCHEMA_FILES="Documentation/devicetree/bindings/arm/ti/k3.yaml"
>    v8make dt_binding_check
> 
> Lokesh Vutla (4):
>    dt-bindings: arm: ti: Add bindings for J7200 SoC
>    dt-bindings: arm: ti: Convert K3 board/soc bindings to DT schema
>    arm64: dts: ti: Add support for J7200 SoC
>    arm64: dts: ti: Add support for J7200 Common Processor Board
> 
>   .../devicetree/bindings/arm/ti/k3.txt         |  26 ---
>   .../devicetree/bindings/arm/ti/k3.yaml        |  28 +++
>   MAINTAINERS                                   |   2 +-
>   arch/arm64/boot/dts/ti/Makefile               |   3 +-
>   .../dts/ti/k3-j7200-common-proc-board.dts     |  64 ++++++
>   arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 199 ++++++++++++++++++
>   .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      |  84 ++++++++
>   arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi   |  29 +++
>   arch/arm64/boot/dts/ti/k3-j7200.dtsi          | 165 +++++++++++++++
>   9 files changed, 572 insertions(+), 28 deletions(-)
>   delete mode 100644 Documentation/devicetree/bindings/arm/ti/k3.txt
>   create mode 100644 Documentation/devicetree/bindings/arm/ti/k3.yaml
>   create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>   create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
>   create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
>   create mode 100644 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
>   create mode 100644 arch/arm64/boot/dts/ti/k3-j7200.dtsi
> 

I have networking enabled on top of this series here.

ssh://git@bitbucket.itg.ti.com/~x1045550/ti-priv-linux-kernel.git ti-linux-5.4.y-for-next-pull

But DMA failed for Main domain.
     0.781005] ti-udma 31150000.dma-controller: NAVSS ti,sci-dev-id read failure -22
[    0.788684] ti-udma: probe of 31150000.dma-controller failed with error -22

http://lcpdresults.itg.ti.com/launcher/results/8013

Is there anything (except my comment for patch 3) which prevents this from been merged?

-- 
Best regards,
grygorii