[PATCH v6 07/13] gpio: add support for the sl28cpld GPIO controller
Andy Shevchenko
andriy.shevchenko at linux.intel.com
Sun Jul 26 05:16:53 EDT 2020
On Sun, Jul 26, 2020 at 01:18:28AM +0200, Michael Walle wrote:
> Add support for the GPIO controller of the sl28 board management
> controller. This driver is part of a multi-function device.
>
> A controller has 8 lines. There are three different flavors:
> full-featured GPIO with interrupt support, input-only and output-only.
FWIW,
Reviewed-by: Andy Shevchenko <andriy.shevchenko at linux.intel.com>
> Signed-off-by: Michael Walle <michael at walle.cc>
> Reviewed-by: Linus Walleij <linus.walleij at linaro.org>
> ---
> Changes since v5:
> - added "select REGMAP_IRQ"
>
> Changes since v4:
> - update copyright year
> - remove #include <linux/of_device.h>, suggested by Andy.
> - use device_get_match_data(), suggested by Andy.
> - drop the irq_support variable, instead call _init_irq() directly,
> suggested by Andy.
> - also move the irq code a bit around to make it look nicer
> - drop "struct sl28cpld_gpio". We don't need to actually store the
> irq_chip and irq_chip_data, everything is device resource managed.
> - use 100 chars line limit, suggested by Andy.
> - remove the platform device table
> - don't use KBUID_MODNAME
>
> Changes since v3:
> - see cover letter
>
> drivers/gpio/Kconfig | 12 +++
> drivers/gpio/Makefile | 1 +
> drivers/gpio/gpio-sl28cpld.c | 161 +++++++++++++++++++++++++++++++++++
> 3 files changed, 174 insertions(+)
> create mode 100644 drivers/gpio/gpio-sl28cpld.c
>
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index 8030fd91a3cc..f6a547b76432 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -1223,6 +1223,18 @@ config GPIO_RC5T583
> This driver provides the support for driving/reading the gpio pins
> of RC5T583 device through standard gpio library.
>
> +config GPIO_SL28CPLD
> + tristate "Kontron sl28cpld GPIO support"
> + select MFD_SIMPLE_MFD_I2C
> + select GPIO_REGMAP
> + select GPIOLIB_IRQCHIP
> + select REGMAP_IRQ
> + help
> + This enables support for the GPIOs found on the Kontron sl28 CPLD.
> +
> + This driver can also be built as a module. If so, the module will be
> + called gpio-sl28cpld.
> +
> config GPIO_STMPE
> bool "STMPE GPIOs"
> depends on MFD_STMPE
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index 4f9abff4f2dc..c3a4e7c94a91 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -132,6 +132,7 @@ obj-$(CONFIG_GPIO_SCH311X) += gpio-sch311x.o
> obj-$(CONFIG_GPIO_SCH) += gpio-sch.o
> obj-$(CONFIG_GPIO_SIFIVE) += gpio-sifive.o
> obj-$(CONFIG_GPIO_SIOX) += gpio-siox.o
> +obj-$(CONFIG_GPIO_SL28CPLD) += gpio-sl28cpld.o
> obj-$(CONFIG_GPIO_SODAVILLE) += gpio-sodaville.o
> obj-$(CONFIG_GPIO_SPEAR_SPICS) += gpio-spear-spics.o
> obj-$(CONFIG_GPIO_SPRD) += gpio-sprd.o
> diff --git a/drivers/gpio/gpio-sl28cpld.c b/drivers/gpio/gpio-sl28cpld.c
> new file mode 100644
> index 000000000000..889b8f5622c2
> --- /dev/null
> +++ b/drivers/gpio/gpio-sl28cpld.c
> @@ -0,0 +1,161 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * sl28cpld GPIO driver
> + *
> + * Copyright 2020 Michael Walle <michael at walle.cc>
> + */
> +
> +#include <linux/device.h>
> +#include <linux/gpio/driver.h>
> +#include <linux/gpio/regmap.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +/* GPIO flavor */
> +#define GPIO_REG_DIR 0x00
> +#define GPIO_REG_OUT 0x01
> +#define GPIO_REG_IN 0x02
> +#define GPIO_REG_IE 0x03
> +#define GPIO_REG_IP 0x04
> +
> +/* input-only flavor */
> +#define GPI_REG_IN 0x00
> +
> +/* output-only flavor */
> +#define GPO_REG_OUT 0x00
> +
> +enum sl28cpld_gpio_type {
> + SL28CPLD_GPIO = 1,
> + SL28CPLD_GPI,
> + SL28CPLD_GPO,
> +};
> +
> +static const struct regmap_irq sl28cpld_gpio_irqs[] = {
> + REGMAP_IRQ_REG_LINE(0, 8),
> + REGMAP_IRQ_REG_LINE(1, 8),
> + REGMAP_IRQ_REG_LINE(2, 8),
> + REGMAP_IRQ_REG_LINE(3, 8),
> + REGMAP_IRQ_REG_LINE(4, 8),
> + REGMAP_IRQ_REG_LINE(5, 8),
> + REGMAP_IRQ_REG_LINE(6, 8),
> + REGMAP_IRQ_REG_LINE(7, 8),
> +};
> +
> +static int sl28cpld_gpio_irq_init(struct platform_device *pdev,
> + unsigned int base,
> + struct gpio_regmap_config *config)
> +{
> + struct regmap_irq_chip_data *irq_data;
> + struct regmap_irq_chip *irq_chip;
> + struct device *dev = &pdev->dev;
> + int irq, ret;
> +
> + if (!device_property_read_bool(dev, "interrupt-controller"))
> + return 0;
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0)
> + return irq;
> +
> + irq_chip = devm_kzalloc(dev, sizeof(*irq_chip), GFP_KERNEL);
> + if (!irq_chip)
> + return -ENOMEM;
> +
> + irq_chip->name = "sl28cpld-gpio-irq",
> + irq_chip->irqs = sl28cpld_gpio_irqs;
> + irq_chip->num_irqs = ARRAY_SIZE(sl28cpld_gpio_irqs);
> + irq_chip->num_regs = 1;
> + irq_chip->status_base = base + GPIO_REG_IP;
> + irq_chip->mask_base = base + GPIO_REG_IE;
> + irq_chip->mask_invert = true,
> + irq_chip->ack_base = base + GPIO_REG_IP;
> +
> + ret = devm_regmap_add_irq_chip_fwnode(dev, dev_fwnode(dev),
> + config->regmap, irq,
> + IRQF_SHARED | IRQF_ONESHOT,
> + 0, irq_chip, &irq_data);
> + if (ret)
> + return ret;
> +
> + config->irq_domain = regmap_irq_get_domain(irq_data);
> +
> + return 0;
> +}
> +
> +static int sl28cpld_gpio_probe(struct platform_device *pdev)
> +{
> + struct gpio_regmap_config config = {0};
> + enum sl28cpld_gpio_type type;
> + struct regmap *regmap;
> + u32 base;
> + int ret;
> +
> + if (!pdev->dev.parent)
> + return -ENODEV;
> +
> + type = (uintptr_t)device_get_match_data(&pdev->dev);
> + if (!type)
> + return -ENODEV;
> +
> + ret = device_property_read_u32(&pdev->dev, "reg", &base);
> + if (ret)
> + return -EINVAL;
> +
> + regmap = dev_get_regmap(pdev->dev.parent, NULL);
> + if (!regmap)
> + return -ENODEV;
> +
> + config.regmap = regmap;
> + config.parent = &pdev->dev;
> + config.ngpio = 8;
> +
> + switch (type) {
> + case SL28CPLD_GPIO:
> + config.reg_dat_base = base + GPIO_REG_IN;
> + config.reg_set_base = base + GPIO_REG_OUT;
> + /* reg_dir_out_base might be zero */
> + config.reg_dir_out_base = GPIO_REGMAP_ADDR(base + GPIO_REG_DIR);
> +
> + /* This type supports interrupts */
> + ret = sl28cpld_gpio_irq_init(pdev, base, &config);
> + if (ret)
> + return ret;
> + break;
> + case SL28CPLD_GPO:
> + config.reg_set_base = base + GPO_REG_OUT;
> + break;
> + case SL28CPLD_GPI:
> + config.reg_dat_base = base + GPI_REG_IN;
> + break;
> + default:
> + dev_err(&pdev->dev, "unknown type %d\n", type);
> + return -ENODEV;
> + }
> +
> + return PTR_ERR_OR_ZERO(devm_gpio_regmap_register(&pdev->dev, &config));
> +}
> +
> +static const struct of_device_id sl28cpld_gpio_of_match[] = {
> + { .compatible = "kontron,sl28cpld-gpio", .data = (void *)SL28CPLD_GPIO },
> + { .compatible = "kontron,sl28cpld-gpi", .data = (void *)SL28CPLD_GPI },
> + { .compatible = "kontron,sl28cpld-gpo", .data = (void *)SL28CPLD_GPO },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, sl28cpld_gpio_of_match);
> +
> +static struct platform_driver sl28cpld_gpio_driver = {
> + .probe = sl28cpld_gpio_probe,
> + .driver = {
> + .name = "sl28cpld-gpio",
> + .of_match_table = sl28cpld_gpio_of_match,
> + },
> +};
> +module_platform_driver(sl28cpld_gpio_driver);
> +
> +MODULE_DESCRIPTION("sl28cpld GPIO Driver");
> +MODULE_AUTHOR("Michael Walle <michael at walle.cc>");
> +MODULE_LICENSE("GPL");
> --
> 2.20.1
>
--
With Best Regards,
Andy Shevchenko
More information about the linux-arm-kernel
mailing list